Box Camera Series Hardware Manual D21 (D21F / D21V) D22 (D22F / D22V) E21 (E21F / E21V) E22 (E22F / E22V) E23, E24, E25 2013/12/04
Hardware Manual Table of Contents Precautions ............................................................. 3 Safety Instructions .................................................................................... 5 Introduction ............................................................. 6 The List of Models ..................................................................................... 6 Package Contents......................................................................................
Hardware Manual Precautions Read these instructions You should read all the safety and operating instructions before using this product. Heed all warnings You must adhere to all the warnings on the product and in the instruction manual. Failure to follow the safety instruction given may directly endanger people, cause damage to the system or to other equipment.
Hardware Manual Federal Communications Commission Statement This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Hardware Manual Safety Instructions Cleaning Disconnect this video product from the power supply before cleaning. Attachments Do not use attachments not recommended by the video product manufacturer as they may cause hazards. Do not use accessories not recommended by the manufacturer Only install this device in a dry place protected from weather Servicing Do not attempt to service this video product yourself. Refer all servicing to qualified service personnel.
Hardware Manual Introduction The List of Models This hardware manual contains the following models: D21F (D21) 1MP Box with D/N, Fixed lens D21V (D21) 1MP Box with D/N, Vari-focal lens D22F (D22) 5MP Box with D/N, Fixed lens D22V (D22) 5MP Box with D/N, Vari-focal lens E21F (E21) 1MP Box with D/N, Basic WDR, Fixed lens E21V (E21) 1MP Box with D/N, Basic WDR, Vari-focal lens E22F (E22) 5MP Box with D/N, Basic WDR, Fixed lens E22V (E22) 5MP Box with D/N, Basic WDR, Vari-focal lens E23 2MP Bo
Hardware Manual E25 1.3MP Box with D/N, Basic WDR, SLLS, Vari-focal lens From the installation perspective these models are very similar; therefore you can use one manual for all of them.
Hardware Manual Package Contents 1. Camera 2. Lens OR Fixed focal lens with manual focus and fixed iris 3. Mounting Block Vari-focal lens with manual focus and DC iris 4. Quick Installation Guide Mounting block for mounting the camera to a bracket.
Hardware Manual Physical Description 1) Ethernet Port The IP device connects to the Ethernet via a standard RJ45 connector. 2) Reset Button The purpose of reset button is to restore the factory default settings of the camera, including administrator’s password. The reset button can be used for following purposes: 1. The administrator’s password has been forgotten and therefore the camera cannot be accessed. 2.
Hardware Manual Installation and Access Camera Installation The box camera may be installed indoors or outdoors (requires waterproof housing). In both cases, the mounting block (included in the package) is needed. Indoor Installation For ceiling installations, the mounting block has to be mounted to the top side of the camera. For wall installations, the mounting block has to be mounted to the bottom side of the camera.
Hardware Manual For pole or corner installations, you may consider following solutions: The housing can be either PMAX-0200, 0201 or PMAX-0202.
Hardware Manual Accessing Camera Connect the Equipment To be able to connect to the camera firmware from your PC, both the camera and the PC have to be connected to each other via Ethernet cable. At the same time, the camera has to have its own power supply. In case of PoE cameras, you can use a PoE Injector or a PoE Switch between the camera and the PC. The cameras that have the DC power connectors may be powered on by using a power adaptor.
Hardware Manual In the example below, we successfully the camera model that we had just connected to the network. By clicking with the mouse click on the camera model, it is possible to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already. If you work with our cameras regularly, then there is even a better way to discover the cameras in the network – by using IP Utility.
Hardware Manual With just one click, you can launch the IP Utility and there will be an instant report as follows: You can quickly notice the camera model in the list. Click on the IP address to automatically launch the default browser of the PC with the IP address of the target camera filled in the address bar of the browser already.
Hardware Manual Manually adjust the IP address of the PC: In the following example, based on Windows 7, we will configure the IP address to 192.168.0.99 and set Subnet Mask to 255.255.255.
Hardware Manual Manually adjust the IP addresses of multiple cameras: If there are more than 1 camera to be used in the same local area network and there is no DHCP server to assign unique IP addresses to each of them, all of the cameras would then have the initial IP address of 192.168.0.100, which is not a proper situation for network devices – all the IP addresses have to be different from each other.
Hardware Manual Access the Camera Now that the camera and the PC are both having their unique IP addresses and are under the same network segment, it is possible to use the Web browser of the PC to access the camera. You can use any of the browsers to access the camera, however, the full functionality is provided only for Microsoft Internet Explorer.
Hardware Manual The following examples in this manual are based on Internet Explorer browser in order to cover all functions of the camera. Assuming that the camera’s IP address is 192.168.0.100, you can access it by opening the Web browser and typing the following address into Web browser’s address bar: http://192.168.0.100 Upon successful connection to the camera, the user interface called Web Configurator would appear together with the login page.
Hardware Manual To check the firmware version through the Web Configurator, access the Setup page and click System > System Info. 1 2 3 For further operations, please refer to the Firmware User Manual.
