User's Manual

BLUE : Pantone Black C
1:0.701
SCALE: REVPART NAMEPART NUMBER
PROPRIETARY AND CONFIDENTIAL : THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF ACSYS. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF ACSYS IS PROHIBITED.
CONFIDENTIAL INDUSTRY
BLUETOOTH PADLOCK USER MANUAL – PL5BLE
USER MANUAL-ENG
421-024A
Folding Marks
Trim Marks
70mm
105mm
USER MANUAL
PL5 BLE
Bluetooth Enabled Padlock
[e-mail]
www.acsys.com
Copyright © 2019 Acsys International Ltd.
1
2
3
• Enter Site ID
• Enter PIN code
• Press
Check-in
or Check-out
depending on the
operation type
1
2
3
OPERATE LOCK
• Press the Open button
next to the Lock name
4
4
• Lock shackle
pops out
Lock is open
6
• Activate Lock
5
CHECK-OUT
• Press the shackle
and hold
4
• Press the Close
button next to the
Lock name
5
• Lock is Closed
6
5
CHECK-IN
REPLACE BATTERY
• Remove the screw
found at the bottom of
the shackle hole
1
• Push the bottom plate
through the shackle hole and
detach it from the padlock body
2
• Replace the battery and
reverse the previous steps
to reassemble
3
JUMP START LOCK
Insert a Micro USB
Cable in the Micro
USB port and connect
it to USB wall charger
or a portable power
bank
USB jump-start port
1
• Remove the Dust Cap
to uncover the USB jump-start port
Jump starting is used when the battery is fully depleted. It serves as a way to wake up the lock, open it
and perform a battery replacement (illustrated in the next section)
2
2
3
While jump-starting, the LED flashes green every 2 seconds
indicating that Bluetooth is advertising during which, the lock
can be opened using the mobile app.
After 60 sec, the lock enters in sleep mode indicated by an
orange LED glow.
If the 60 sec have elapsed, press the Bluetooth button or
remove and reconnect the USB power to put the lock in
Bluetooth advertising mode again.
Open the padlock using the mobile app and perform the battery
replacement procedure shown below.
4
5
INSTALL APP
• Search for “Acsys Mobile App” on your device app store
• Download and install the app on your device
METHOD 2
1
2
3
4
• On the welcome screen, select “Acsys iAMS Enterprise” from the available app types
• Register the app by following the on-screen instructions
• Scan this QR code
• Download the Acsys BLE mobile app
for your respective platform
DO NOT SCAN the QR code on
the padlock bottom cover
or on the padlock
package.
1
2
METHOD 1
REGISTER LOCK
• Activate Lock
7
1
2
3
• Open Main Menu
Add Access Point
• Enter Site ID
• Enter PIN code
• Press Register
1
2
3
4
4
6
• Add Access Point
• Enter Lock ID
or scan QR Code on
the lock
5
6
5
• Lock is registered
8
DELETE LOCK
• Activate Lock
7
1
2
3
• Open Main Menu
Delete Access Point
• Enter Site ID
• Enter PIN code
• Press Delete
1
2
3
4
4
• Press the Delete
button next to the
correct Lock name
5
5
• Lock is deleted
8
ACTION STATE
INITIALIZED LOCK INDICATION
Bluetooth advertising
Lock is open and
shackle is pushed closed
1 green flash every 2 sec
for 60 sec
BLANK LOCK INDICATION
1 red flash every 2 sec
for 60 sec
1 red flash every 2 sec
1 green flash, every 2 sec
until shackle is released
Press
Bluetooth button
Press and Hold
shackle
Operation successful
Operation failure
1 quick green flash
1 quick orange flash
1 quick green flash 1 quick red flash
Initialize, Delete
Open, Close
Battery
Replacement
Bluetooth advertising
Sleep mode
USB
jump start
1 green flash, every 2 sec for 60 sec
orange glow
1 red flash, every 2 sec for 60 sec
orange glow
LED INDICATIONS
• Don’t attempt to remove the Lithium-(CR2) battery from this product without consulting an Acsys
authorized installer first.
CAUTION
• This user manual is for reference only. Minor differences can be found in user interface.
• Please follow the instructions to set up your device. In case of any issue, please contact Acsys Support
• Specifications may be altered without prior written notice.
NOTE
-10C
+60C
0
95%
without
condensation
SPECIFICATIONS
Dimensions & Weight 70 x 125 x 31 mm | 11mm shackle | 900g
Lithium (CR2) | Non-Rechargeable | Jump-Start
Power Type
Tricolor LED
Visual Indicator
FCC STATEMENT
FCC ID:
2AR93-116P1948
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.SPECIFICATIONS
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.