READ THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE THIS BED. F1427-13 SAFETY WARNINGS AND GENERAL NOTES: + Follow the information on the wakings appearing on the upper bunk bed end structure and cn the carton. Do not remove the waning label from the bed. = Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood of entrapment or falls. (See Page 12) * The top surface of the mattress must be at least 5" below the upper edge of the guardrails.
HARDWARE LIST 5 2 HOLE L-BRACKET 2MM} A 10PCS||B 26 PCS||C 6 PCS PLASTIC DOWEL (M8 x 30MM) PLASTIC DOWEL {M10 x 35MM} CBC BOLT {Mé x 35MM) D 24PCS||E 22PCS||F PCS CBC BOLT {Mé x 60MM) JRN NUT {Mé x 13MM) CONNECTING BOLT (34MM) G 5PCS||H 4PCS||J 6 PCS %, “ MINI FIX {12MM} CSK C/B SCREW {M3.5 x 12MM} CSK C/B SCREW {M4 x 25MM) 2PCS||L 1PC SN ALLEN KEY [M4 x 60MM} Make sure all the fasteners are tight. The assembly wil require at least two people to complete.
PART LIST [oy SHELF PANEL (1 PC / SET) CARTON 2 OF 2 HEADBOARD SUPPORT {1 PC / SET} CARTON SET) CARTON 1 OF 2 FOOT BOARD FRONT GUARD RAIL REAR GUARD RAIL (1 PC / SET} (1 PC / SET} (1 PC / SET} CARTON 1 OF 2 CARTON 2 OF 2 CARTON Whe LADDER SLAT WOODEN SLAT {4 PCS / SET) [13 PCS / SET) CARTON 2 OF 2 CARTON 1 OF 2 LADDER SIDE CARTON CARTON O [2 PCS / SET) CARTON 2 OF 2 PAGE 162 LB {990 x 1905} MAST WSN 171127 (1)
BEDDING SPECIFICATION (MINIMUM DISTANCE 5" FROM TOP OF GUARDRAIL TO TOP OF MATTRESS) GUARDRAIL or MAXIMUM THICKNESS MATTRESS SIDE RAIL TT WOODEN SLATS ] MATTRESS SIZE Upper Bunk Mattress Specification : « Only use a mattress that long and 37 1/2" 38 1/2" wide on upper bunk. « Ensure thickness of mattress does not exceed 9". Replacement parts : Replacement parts, including additional guard rails, can be obtained from any SASSANIAN SDN. BHD. distributor or retailer.
HARDWARE LIST A 24 PCS — PLASTIC DOWEL (Mé x 30MM} 18 PCS & PLASTIC DOWEL (M8 x 30MM} c 22 PCS rd CONNECTING BOLT (34MM) D 6 PCS 16 PCS||F 6 PCS 5 > MINI FIX (SMM) MINI FIX {12MM} CSK C/B SCREW (M4 X 32MM) G 14 PCS 2PCS| Tool Required : Cross head Screw Driver P/H C/B SCREW {M3.
PART LIST TOP PANEL {1PC/SET} CARTON 10OF 1 SIDE PANEL (1PC/SET} CARTON 1 OF 1 BOTTOM RAIL (1PC/SET) CARTON 1 OF 1 SIDE PANEL SIDE PANEL DRAWER UNIT (1) DRAWER UNIT (R) {1PC/SET) {1 PC /SET) CARTON 10F 1 CARTON 1 OF 1 RAIL DRAWER UNIT TOP RAIL {PCS / SET) {1PC/SET} CARTON 10F 1 CARTON 1 OF 1 BACK PANEL (1PC/SET) CARTON 1 OF 1 DRAWER FACE DRAWER SIDE (L&R) DRAWER REAR DRAWER BASE (PCS/ SET) {PCS /SET) (PCS /SET} (3PCS/SET} CARTON 1 OF 1 CARTON 10F 1 CARTON 10F 1 CARTON 10F 1 PAGE OF 8 WS 162-DK-WSN-171124(1)
STEP 1 Insert (B) into specified 28MM holes on Side Panel {2L.2R & 3) and All {4,5 & §) by using a Rubber Hammer.
STEP 5 Attach and secure All (§ & é) onto Side Panel (2R & 3} and insert (E) to tighten it up by using Cross head Screw Driver. STEP & Attach and secure Top Pane! {1) onto Previously Assembly and Insert (E) fo tighten if up by using Cross head Screw Driver. Insert (H) from underneath Rail (8) fo frighten it up by using Cross head Screw Driver.
STEP 7 Attach Back Panel (7) onto Previous Assembly and use (G) to secure and frighten it up by using Cross head Screw Driver. STEP 8 Attach and secure Drawer Side STEP 9 Drawer Rear (10) and insert (A) and (F) to Slot Drawer Base (11) into the groove Ines at tighten Tt up by using Cross head Screw Driver. Drawer Side {9L & 7R) and Drawer Rear (10).
Attach and secure Drawer Face (8) fo Previous Assembly and insert (A) and (C), use (D) to secure and tighten it up by using Cross head Screw Driver. STEP 10 RN AOA 162 DK WSN 171124 (1) Insert Drawers into previous Assembly.
PART LIST TOP PANEL {1 PC / SEN) CARTON 2 OF 2 SIDE PANEL (LEFT) SIDE PANEL (RIGHT) {1PC /SET) {1 PC / SET) CARTON 1 OF2 CARTON 1 OF 2 SHELF BOTTOM PANEL TOP RAIL {1 PC/ SET) {1 PC / SET) [PCS / SET) CARTON 2 OF 2 CARTON 2 OF 2 CARTON SET) REAR RAIL (TOP) REAR RAIL (BOTTOM) SET) {1 PC / SET} CARTON 2 OF 2 CARTON 2 OF 2 CARTON 2 OF 2 BACK PANEL {3 PCS / SET) DOOR CARTON PCS / SET) CARTON 1 OF 2 PAGE 162-2DR WD WSN 171124 (T)