Aspire 1410/1680 Series Service Guide
Revision History Please refer to the table below for the updates made on Aspire 1410/1680 service guide.
Copyright Copyright © 2004 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV Screen messages Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
V.7 5/312004 Shipping priority Quanta Named Project Name Platform naming M/B Chipset Kestrel / Extensa /ZL1 Series Model Comparision Table No. 5 No. 6 No. 4 ZL1 No. 3 No. 1 on Jul.20th ZL1A No. 2 ZL1C ZL1E Kestrel-E-UMA TM2300 VERSION A6 852GM Kestrel-P-M11P64 TM4500 VERSION A1 855GME Kestrel-P-UMA TM4500 VERSION A2 855GME Kestrel-M11P64 TM4000 VERSION A3 855GME Kestrel-UMA TM4000 VERSION A4 855GME Kestrel-A-M11P64 AS1680 VERSION A5 855GME Kestrel-A-UMA AS1680 VERSION A4 855GME Banias 1.
Table of Contents Chapter 1 System Introduction 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Top View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Disassembling the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 Disassembling the External Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Disassembling the Optical Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Chapter 4 Troubleshooting 68 System Check Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IX
Chapter 1 System Introduction Features Below is a brief summary of the computer’s many feature: Performance T Intel® Pentium M® processor 705, 715, 725, 735, 745, 755 or Intel® Celeron M® processor 320,330 T Intel® 855GME or 852 GM chipset (manufacturing option) T 256/512 MB of DDR333 SDRAM standard, upgradeable to 2048 MB with dual soDimm modules T 30 GB and above high-capacity, Enhanced-IDE hard disk T Advanced Configuration Power Interface (ACPI) power management system.
T SD/MMC/MS memory card reader (manufacturing option) Human-centric design and ergonomics T Rugged, yet extremely portable design T Stylish appearance T Full-size keyboard with four programmable launch keys T Ergonomically-centered touchpad pointing device T Internet 4-way scroll button Keyboard and Pointing Device T 88/89-key Windows keyboard T Ergonomically-centered touchpad pointing device with scroll function Expansion T One Type II CardBus PC Card slot T Upgradeable memory modules T
System Block Diagram A B C D 1 5V / 3.3V / 12V Page : 10 2.5V / 1.25V / 1.8V Page : 10 1.5V / 1.2V Page : 10 CPU CORE Page : 10 VGA CORE/VRAM Page : 10 BATTERY CHARGER Page : 10 BATTERY SELECT Page : 10 1 5VPCU 3V_ALWAYS +12V +5V 3V_S5 5V_S5 3VSUS 5VSUS 2.5VSUS +2.5V +1.8V MVREF_DM SMDDR_VTERM 1.5V_S5 +1.5V AGP_VCC (+1.5V) 1.2VCCT VTT VCC_CORE VGA_CORE LINE IN 2 MIC IN Page:13 2.
Board Layout Top View 1 4 Keyboard Connector 7 3 in 1 Connector 2 Bluetooth Board Connector 8 Speaker Connector 3 LCD Cable Connector 9 Internal Microphone Connector 4 LED Board Connector 10 Modem Board Connector 5 Lid Switch 11 Touchpad Board Connector 6 Modem Cable Connector Chapter 1
Bottom View 1 Power Jack 16 Audio Cable Connector 2 CRT 17 Line-in Connector 3 Docking 18 Headphone Out Connector 4 Audio Cable Connector 19 Microphone-in Connector 5 Main Battery Connector 20 USB Connector 6 ODD Connector 21 IEEE 1394 Connector 7 Media Bay Connector 22 PCMCIA 8 Mini PCI Slot 23 USB Connector 9 Second Battery Connector 24 CPU Socket 10 RTC Battery Connector 25 USB Connector 11 DDR DIMM Connector 26 S-Video 12 HDD Connector 27 RJ45 and RJ11 Con
13 6 IR 28 LAN Cable Connector 14 Bluetooth Switch 29 FAN Connector 15 Wireless Switch 30 LAN Cable Connector Chapter 1
An Aspire Tour After knowing your computer features, let us show you around your new Aspire computer. Front View # Icon Item Description 1 Display screen Also called LCD (liquid-crystal display), displays computer output. 2 Microphone Internal microphone for sound recording. 3 Keyboard Inputs data into your computer. 4 Palmrest Comfortable support area for our hands when you use the computer.
Closed Front View # Icon Item Description 1 Speakers Left and right speakers deliver stereo audio output. 2 Infrared port Interfaces with infrared devices (e.g., infrared printer, IR-aware computer). 3 Power indicator Lights when the computer is on. 4 Battery indicator Lights when the battery is being charged 5 Bluetooth® communications Indicates that (optional) Bluetooth is enabled. 6 Wireless communication Indicates status of wireless LAN communication.
Left View # 1 Chapter 1 Icon Item Description Optical drive Internal optical drive; accepts CDs or DVDs depending on the optical drive type. 2 LED indicator Lights up when the optical drive is active. 3 Optical drive eject button Ejects the optical drive is active. 4 Emergency eject hole Ejects the optical drive tray when the computer is turned off.
Right View # Icon Item Description 1 IEEE 1394 port (Manufacturing option) Connects to IEEE 1394 devices. 2 PC Card slot eject button Ejects the PC Card from the slot. 3 PC Card slot Connects to one Type II CardBus PC Card. 4 3-in-1 card reader Accepts MS, MMC and SD card. Note: The 3-in-1 card reader is a manufacturing option, subject to configuration. Only one card can operate at any given time. 10 5 Two USB 2.0 ports Connects to Universal Serial Bus (USB) 2.0 devices (e.g.
Rear Panel # Chapter 1 Icon Item Description 1 Power jace Connects to an AC adapter. 2 External display port Connects a display device (e.g., external monitor, LCD projector). 3 Security keylock Connects to a Kensington-compatible computer security lock.
Bottom Panel # 1 Item Cooling fan Description Helps keep the computer cool. Note: Do not cover or obstruct the opening of the fan. 12 2 Battery lock Locks the battery in place. 3 Memory compartment Houses the computer’s main memory. 4 Hard disk bay Houses the computer’s hard disk (secured by a screw). 6 Battery release latch Unlatches the battery to remove the battery pack. 7 Battery bay Houses the computer’s battery pack.
Indicators The computer has three easy-to-read status icons on the upper-right above the keyboard. Icon Chapter 1 Function Description Caps lock Lights when Caps Lock is activated. Num lock Lights when Num Lock is activated. Media Activity Lights when the hard disk or optical drive is active.
In addition, there are two indicators at the front panel. Even when the cover is closed, the state or features can still be seen. Icon 14 Function Description Power Lights when the computer is on. Battery indicator Lights when the battery is being charged.
Using the Keyboard The keyboard has full-sized keys and an embedded keypad, separate cursor keys, two Windows keys and twelve function keys. Lock Keys The keyboard has three lock keys which you can toggle on and off. Lock Key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num lock (Fn-F11) When Num Lock is on, the embedded keypad is in numeric mode. The keys function as a calculator (complete with the arithmetic operators +, -, *, and /).
Embedded Numeric Keypad The embedded numeric keypad functions like a desktop numeric keypad. It is indicated by small characters located on the upper right corner of the keycaps. To simplify the keyboard legend, cursor-control key symbols are not printed on the keys. Desired Access 16 Num Lock On Num Lock Off Number keys on embedded keypad Type numbers in a normal manner. Cursor-control keys on embedded keypad Hold j while using cursor-control keys. Hold Fn while using cursorcontrol keys.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Windows key Icon Description Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hot keys or key combinations to access most of the computer’s controls like sreen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the Fn key before pressing the other key in the hot key combination. Hot Key 18 Icon Function Description Fn-F1 Hot key help Displays help on hot keys. Fn-F2 Acer eSetting Launches the Acer eSetting in the Acer eManager set by the Acer Empowering key.
Hot Key Icon Function Description Fn-y Volume down Decreases the speaker volume. Fn-x Brightness up Increases the screen brightness. Fn-z Brightness down Decreases the screen brightness Fn-Home Play/Pause Press to start playing the audio track or video file. Press again to pause. Fn-Pg Up Stop Press to stop playing the audio track or video file. Fn-Pg Dn Backwards Press to skip backward to the previous track or video file and start playing.
Special Key You can locate the Euro symbol and US dollar sign at the upper-center and/or bottom-right of your keyboard. To type: The Euro symbol 1. Open a text editor or word processor. 2. Either directly press the Euro symbol at the bottom-right of the keyboard, or hold Alt Gr and then press the Euro symbol at the upper-center of the keyboard. The US dollar sign 1. Open a text editor or word processor. 2.
Launch Keys Located at the upper-right above the keyboard are four buttons. These buttons are called launch keys. They are designated as the mail, Web browser, Empowering and programmable keys. Press the Acer Empowering Key to run the Acer EManager. The mail and Web browser are default for Email and Internet programs, but can be reset by users. To set the mail, Web browser and programmable keys, run the acer Launch Manager.
In addition, there are two launch keys at the front panel. Even when the cover is closed, you can easily access the features of Wireless and Bluetooth®. However, the Wireless and Bluetooth keys cannot be set by users. Description 22 Default application communications Lights to indicate the status of Bluetooth (optional) communications. Wireless communications Lights to indicate the status of wireless LAN (optional) communications.
Touchpad The built-in touchpad is a PS/2-compatible pointing device that senses movement on its surface. This means the cursor responds as you move your finger on the surface of the touchpad. The central location on the palmrest provides optimum comfort and support. NOTE: If you are using an external USB or serial mouse, you can press Fn-F7 to disable the touchpad. Touchpad Basics The following teaches you how to use the touchpad: T Move your finger across the touchpad to move the cursor.
NOTE: Keep your fingers dry and clean when using the touchpad. Also keep the touchpad dry and clean. The touchpad is sensitive to finger movements. Hence, the lighter the touch, the better the response. Tapping too hard will not increase the touchpad’s responsiveness.
Hardware Specifications and Configurations Processor Item CPU type Specification Intel Celeron M processor at 1.3GHz~1.4GHZ for Aspire 1410 Intel Pentim M processor at 1.5GHz~1.6GHz (Dothan) for Aspire 1680 Core logic Intel 855GME+ICH4 CPU package Intel socketable 478pin Micro-BGA CPU core voltage 1.308V (highest frequency mode) to 0.956V (low frequency mode) 0.
Memory Combinations Slot 1 Slot 2 Total Memory 0MB 128MB 128MB 0MB 256MB 256MB 0MB 512MB 512MB 0MB 1024MB 1024MB 128MB 128MB 256MB 128MB 256MB 384MB 128MB 512MB 640MB 128MB 1024MB 1152MB 256MB 128MB 384MB 256MB 256MB 512MB 256MB 512MB 768MB 256MB 1024MB 1280MB 512MB 128MB 640MB 512MB 256MB 768MB 512MB 512MB 1024MB 512MB 1024MB 1536MB 1024MB 0MB 1024MB 1024MB 128MB 1125MB 1024MB 256MB 1280MB 1024MB 512MB 1536MB 1024MB 1024MB 2048MB NOTE: Above
Modem Interface Item Specification Data modem data baud rate (bps) 56K Supports modem protocol V.90/V.92 Modem connector type RJ11 Modem connector location Right panel Bluetooth Interface Item Specification Chipset Broadcom BCM2035 Data throughput 723 bps(full speed data rate) Protocol Bluetooth 1.1 (Upgradeable to Bluetooth 1.2 when SIG specification is ratified). Interface USB 1.1 Connector type Mini-USB Wireless Module 802.
Hard Disk Drive Interface Item Specification Drive Format Disks 1 1 2 2 Spindle speed (RPM) 4200 RPM 4200 RPM 4200 RPM 4200 RPM 2048KB 8192KB 8192KB Performance Specifications Buffer size 2048KB/ Interface ATA/ATAPI-6; ATA-6 ATA/ATAPI-6; ATA-6 ATA/ATAPI-6; ATA-6 ATA/ATA-6; ATA-6 Max. media transfer rate (disk-buffer, Mbytes/s) 372 372 350 350 Data transfer rate (host~buffer, Mbytes/s) 100 MB/Sec. Ultra DMA mode-5 100 MB/Sec. Ultra DMA mode-5 100 MB/Sec.
DVD-Dual Interface Item Specification Applicable disc format Support disc formats 1. Reads data in each CD-ROM, CD-ROM XA, CD-1, Video CD, CD-Extra and CD-Text 2. Reads data in Photo CD (single and Multi-session) 3. Reads standard CD-DA 4. Reads and writes CD-R discs 5. Reads and writes CD-RW discs 6. Reads and writes in each dVD+R/RW (Ver. 1.1) 7. Reads data in each DVD-ROM and DVD-R (Ver. 2.0 for Authoring) 8. Reads and writes in each DVD-R (Ver. 2.0 for general), DVD-RW and DVD+R/RW (Ver1.
Video Memory Item Specification Chipset Intel 855GME/ATI M11P (ATI Mobility RADEON 9700) Memory size UMA 16/32/64MB, discrete 64MB Interface DDR USB Port Item Specification Chipset ICH4-M USB Compliancy Level 2.0 OHCI USB 1.1 and USB 2.
System Board Major Chips Item Controller Wireless 802.11 b+g Intel PCMCIA TI PC7411 Audio Conexant RD01-D620 3-in-1 card reader TI PC7411 Keyboard Item Specification Keyboard controller NS PC97551 Total number of keypads 88-/89-key Windows logo key Yes Internal & external keyboard work simultaneously 1. Plug USB keyboard to the USB port directly: Yes 2.
LCD 14.1 inch for Aspire 1410 Item Specification Typical Power Consumption (watt) 5.3 4.03 (for backlight unit) N/A Weight 400g (w/o inverter) 420g 460g Physical Size(mm) 299(W)x228(H)x5.5 (D) 299(W)x228(H)x5.2 (D) 299(W)x228(H)x6.
LCD 15 inch and 15.4 inch Item Vendor & model name Specification SAMSUNG LTN150XB-L03 Hitachi Active Area (mm) 304.1x228.1 Display resolution (pixels) 1024x768 XGA 1024x768 XGA 1280x800 WXGA Pixel Pitch 0.297x0.297 0.297x0.297 0.2588x0.2588 Pixel Arrangement R.G.B. Vertical Stripe R.G.B. Vertical Stripe R.G.B. Vertical Stripe Display Mode Normally White Transmissive & normally White Normally White Typical White Luminance (cd/m2) 160 170 185 Luminance Uniformity N/A 40 1.
AC Adaptor Item Specification Maximum input AC current 3.42A Inrush current 220A@115VAC 220A@230VAC Efficiency 82% min. @115VAC input full load System Power Management ACPI mode 34 Power Management Mech. Off (G3) All devices in the system are turned off completely. Soft Off (G2/S5) OS initiated shutdown. All devices in the system are turned off completely. Working (G0/S0) Individual devices such as the CPU and hard disc may be power managed in this state.
Chapter 1 35
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Navigating the BIOS Utility There are six menu options: Info., Main, System Devices, Security, Boot, and Exit. Follow these instructions: T To choose a menu, use the cursor left/right keys (zx). T To choose a parameter, use the cursor up/down keys ( wy). T To change the value of a parameter, press por q. T A plus sign (+) indicates the item has sub-items. Press e to expand this item. T Press ^ while you are in any of the menu options to go to the Exit menu.
Information PhoenixBIOS Setup Utility . Info. Main Advanced Security Boot CPU Type: CPU Speed: Intel (R) Pentium (R) M processor 1.
Main The Main screen displays a summary of your computer hardware information, and also includes basic setup parameters. It allows the user to specify standard IBM PC AT system parameters. PhoenixBIOS Setup Utility Info. Advanced Main Security Boot Exit Item Specific Help System Time: [05:34:07] System Date: [07/23/2004] System Memory: 640 KB selects field.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Format/Option System Time Sets the system time. The hours are displayed with 24-hour format. Format: HH:MM:SS (hour:minute:second) System Time System Date Sets the system date. Format MM/DD/YYYY (month/day/ year) System Date System Memory This field reports the memory size of the system.
Advanced The Advanced menu screen contains parameters involving your hardware devices. It also provides advanced settings of the system. PhoenixBIOS Setup Utility Info.
Parameter Description Options Legacy USB Support Enables, disables USB interface devices support. (Enable for use with a non-USB aware Operating System such as DOS or UNIX). Option: Disabled or Enabled Hard Disk Recovery Enables or disables Hard Disk to Hard Disk system Recovery by pressing Fn+F10 key during POST.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Info.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Option User Password is Shows the setting of the user password. Clear or Set Supervisor Password is Shows the setting of the Supervisor password Clear or Set Set User Password Press Enter to set the user password. When user password is set, this password protects the BIOS Setup Utility from unauthorized access.
3. 4. Press e. After setting the password, the computer sets the User Password parameter to “Set”. If desired, you can opt to enable the Password on boot parameter. 5. When you are done, press u to save the changes and exit the BIOS Setup Utility. Removing a Password Follow these steps: 1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears: 2. Type the current password in the Enter Current Password field and press e. 3.
If the verification is OK, the screen will display as following. The password setting is complete after the user presses u. If the current password entered does not match the actual current password, the screen will show you the Setup Warning. If the new password and confirm new password strings do not match, the screen will display the following message.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. PhoenixBIOS Setup Utility Info. Main Advanced Security Boot Exit Item Specific Help CD-ROM/DVD Drive + and - indicate device categories. Use to expand/collapses. Floppy Devices +Hard Drive Network Boot Boot order is top-down using only the top device in each category.
Exit The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use. PhoenixBIOS Setup Utility Info. Main Advanced Security Exit Boot Item Specific Help Exit Saving Changes Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: T New versions of system programs T New features or options T Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. To disassemble the computer, you need the following tools: T Wrist grounding strap and conductive mat for preventing electrostatic discharge T Small Philips screw driver T Philips screwdriver T Plastic flat head screw driver Tweezers NOTE: The screws for the different components vary in size.
General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Remove the battery pack. NOTE: The screws used to secure bottom case and upper case are more than one type. Please group same type of screw together as you disassemble the system for service purpose. The image below is for your reference.
Screw Type Location Quantity M2.5*6 Bottom case and IO bezel (hightlight with yellow circle) 14 M2.5*6 Remove the IO bezel then you will see. 2 M2.5*6 Remove the heatsink cover then you will see. 1 M2.5*6 Remove the HDD cover then you will see. 1 M2.5*3 Detach the HDD module then you will see. 1 M2.5*3 Remove the battery then you will see.
Disassembly Procedure Flowchart The flowchart on the succeeding page gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the system board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
LCD Module 4 screw pads M*4 LCD Bezel *6 hinges *2 brackets LCD Inverter Antenna set LCD Cover LCD Assembly *4 LCD LCD Cable LCD Brackets Screw List Item Chapter 3 Description SCREW M2.0X3.0-I-NINYLOK 86.A03V7.012 SCREW I2.5*3MBNIH(M2.5L3) 86.T25V7.012 SCREW M2.5*4L-BZNNYLOK 86.A03V7.006 SCREW M2.0X5-I-NINYLOK 86.T23V7.006 SCREW MM25060IL69 86.A08V7.004 SCREW M2.0*5I(NI)(NYLOK) 86.T23V7.010 SCREW M2.0X2.5-I-NINYLOK 86.A03V7.007 SCREW I2*3M-NIHY (M2L3) 86.T25V7.008 SCREW M1.7*3.
Removing the Battery Pack 55 1. Unlock the battery lock. 2. Slide the battery latch as shown then remove the battery pack.
Removing the HDD Module/the Memory and the Wireless LAN Card/ the Thermal Module and the CPU/ODD Module and LCD Module Removing the HDD Module 1. Remove the two screws holding the HDD cover. 2. Remove the HDD cover. 3. Detach the HDD module then remove it. Removing the Memory and the Wireless LAN Card 1. Remove the two screws that secure the RAM/Wireless cover. 2. Remove the RAM/Wireless cover. 3. Pop up the memory then remove it. 4. Disconnect the auxiliary and the main wireless antennae. 5.
2. Then remove the IO bezel. 3. Remove the two screws that secure the heatsink cover. 4. Remove the heatsink cover from the main unit. 5. Disconnect the fan cable. 6. Remove the four screws that secure the thermal module. 7. Pull the thermal module outwards then remove it. NOTE: The edge of the thermal module as shown is very sharp. Be very careful as you remove the thermal module. 57 8. Use a flat-bladed screwdriver to release the CPU lock. 9. Remove the CPU from the socket carefully.
Removing the ODD Module 1. Release the ODD latch. 2. Remove the ODD module from the main unit. . Removing the LCD Module 1. Remove the three screws holding the keyboard cover. 2. Open the LCD module as the picture shown then detach the keyboard cover from the main unit. 3. Remove the two screws that secure the keyboard as shown. 4. Turn over the keyboard as shown and disconnect the keyboard cable then remove the keyboard. 5.
8. Then detach the LCD module from the main unit. .
Disassembling the Main Unit Separate the Main Unit Into the Upper and the Lower Case Assembly 1. Remove the two screws holding the switch board. 2. Remove the switch board. 3. Disconnect the touchpad FFC from the main board. 4. Disconnect the bluetooth cable. 5. Remove the five screws that secure the upper case. 6. Remove the eighteen screws on the bottom as shown. 7. Detach the upper case assembly and place it next to the lower case assembly. 8.
4. Remove the three screws that secure the touchpad board. 5. Remove the touchpad board from the upper case. 6. Disconnect the touchpad board to touchpad FFC. 7. Remove the touchpad board to touchpad FFC from the uppwer case assembly. 8. Remove the four screws holding the touchpad bracket. 9. Detach the touchpad bracket from the upper case assembly. 10. Remove the touchpad from the upper case. 11. Remove the two screws that secure the bluetooth module. 12.
1. Disconnect the MDC cable from the modem board. 2. Detach the MDC cable from the main board. 3. Remove the two screws holding the modem board. 4. Remove the modem board from the lower case. 5. Disconnect the speaker cable from the main board. 6. Remove the two screws that secure the main board. 7. Remove the two screw nuts as shown. 8. The you can detach the main board from the upper case. 9. Remove the three screws that secure the VGA heatsink. 10.
63 Chapter 3
Disassembling the LCD Module 1. Remove the four screw caps as shown. 2. Remove the four screws holding the LCD bezel. 3. Then detach the LCD bezel from the LCD module. 4. Disconnect the inverter board then remove it. 5. Remove the three screws holding the right hinge. 6. Then remove the three screws that secure the left hinge. 7. Remove one screw that secure the LCD bracket. 8. Remove another screw holding the LCD bracket on the other side. 9.
13. Remove the left bracket as the picture shows. 14. Tear off the tape fastening the LCD cable. 15. Tear off the the LCD cable fastening the LCD cable, then remove it..
Disassembling the External Modules Disassembling the HDD Module 1. Remove the two screws holding the HDD bracket on one side. 2. Remove another two screws holding the HDD bracket on the other side. 3. Then take the hard disc drive out from the HDD bracket. Disassembling the Optical Drive Module 1. Remove the four screws as the picture shows. 2. Remove the two screws that secure the optical disc drive and the ODD holder. 3. Push the ODD holder as shown. 4. Detach the ODD holder. 5.
67 Chapter 3
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: T Replace the System board. T If the problem is not corrected, see “Undetermined Problems” on page 82. T If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes 006 Error Messages Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages Real time clock error FRU/Action in Sequence RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility. RTC battery System board Memory size found by POST differed from CMOS Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages No beep, power-on indicator turns off and LCD is blank. FRU/Action in Sequence Power source (battery pack and power adapter). See “Power System Check” on page 70. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 70.
POST Code Code For Boot Block in Flash ROM E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize the system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize Multi Processor EAh Initialize OEM special code EBh Initialize PIC and DMA ECh Initialize Memory type EDh Initialize Memory size EEh Shadow Boot Block EFh System memory test F0h Initialize interrup
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error LCD backlight doesn't work Action in Sequence LCD is too dark Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. LCD brightness cannot be adjusted Reconnect the LCD connectors. LCD contrast cannot be adjusted Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Battery can’t be charged Action in Sequence See “Check the Battery Pack” on page 72. Battery pack System board PCMCIA-Related Symptoms Symptom / Error System cannot detect the PC Card (PCMCIA) Action in Sequence PCMCIA slot assembly System board PCMCIA slot pin is damaged. PCMCIA slot assembly Memory-Related Symptoms Symptom / Error Memory count (size) appears different from actual size.
Power Management-Related Symptoms Symptom / Error Battery fuel gauge in Windows doesn’t go higher than 90%. Action in Sequence Remove battery pack and let it cool for 2 hours. Refresh battery (continue use battery until power off, then charge battery). Battery pack System board System hangs intermittently. Reconnect hard disk/CD-ROM drives. Hard disk connection board System board Peripheral-Related Symptoms Symptom / Error Action in Sequence System configuration does not match the installed devices.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 81 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 70): 1.
Use NAPP CD to Build Master Hard Disc Drive CD to Disk Recovery 83 1. Prepare NAPP CD, Recovery CD and System CD. 2. Put NAPP CD into the optical drive. Then boot up the system. 3. The system will ask you if you want to build NAPP Master HDD. Please press any key to continue. 4. NAPP CD will start to preload the system, please click [Y]. 5. Select CD to Disk Revocery.
6. Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till you finish all Recovery CDs. After you place the Recovery CD to the optical drive, you will see the display below.
85 7. Then insert the System CD to the optical drive. 8. You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Disk to Disk Recovery 1. Prepare NAPP CD, Recovery CD and System CD. 2. Put NAPP CD into the optical drive. Then boot up the system. 3. The system will ask you if you want to build NAPP Master HDD. Please press any key to continue. 4. NAPP CD will start to preload the system, please click [Y].
5. Select Disk to Disk Recovery. Then choose Single Language or Multi-Languages Recovery. NOTE: For Multi-Languages Recovery, not more than five languages could be loaded to the system. 6. 87 Put the Recovery CD to the optical drive. This step is to create image files to the system, you do not have to put the Recovery CD to the optical drive in order. Place one Recovery CD to the drive at one time till you finish all Recovery CDs.
After you place the Recovery CD to the optical drive, you will see the display below. 7. Then insert the System CD to the optical drive.
8. 89 You will see the screen displaying “PASS” when the system has buit NAPP Master hard disc drive.
Chapter 5 Jumper and Connector Locations Top View 1 Keyboard Connector CN5 7 3 in 1 Connector CN10 2 Bluetooth Board Connector CN6 8 Speaker Connector CN12 3 LCD Cable Connector CN2 9 Internal Microphone Connector CN11 Chapter 5 90
91 4 LED Board Connector CN3 10 Modem Board Connector CN9 5 6 Lid Switch SW2 11 Touchpad Board Connector CN8 Modem Cable Connector CN4 Chapter 5
Bottom View 1 Power Jack CN13 16 Audio Cable Connector CN34 2 CRT CN14 17 Line-in Connector CN39 3 Docking CN15 18 Headphone Out Connector CN37 4 Audio Cable Connector CN16 19 Microphone-in Connector CN38 5 Main Battery Connector CN18 20 USB Connector CN36 6 ODD Connector CN19 21 IEEE 1394 Connector CN35 7 Media Bay Connector CN23 22 PCMCIA CN30 8 Mini PCI Slot CN24 23 USB Connector CN28 9 Second Battery Connector CN26 24 CPU Socket U41 10 RTC Battery
93 14 Bluetooth Switch SW4 29 FAN Connector CN20 15 Wireless Switch SW3 30 LAN Cable Connector CN17 Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Aspire 1680/1410. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Exploded Diagram 95 Chapter 6
Adapter N/S ADAPTER 65W 3 PIN DELTA SADP65KB BF 19V TBD N/S ADAPTER 65W 3 PIN LITE-ON PA1650-02 QA 19V TBD N/S ADAPTER 65W 3 PIN LI-SHIN SLS0335A 19V TBD N/S BATTERY SANYO LI-ION 4S2P 4.4A 4UR18650F-2-QC140 TBD BATTERY PANASONIC LI-ION 4S2P 4.4A CGR-B/8B5AE TBD BATTERY SIMPLO LI-ION 4S2P 4.4A 916-3020 TBD 9 MODEM BOARD 54.T50V7.001 14 BLUETOOTH MODULE W/ANTENNA 54.T48V7.001 N/S WIRELESS LAN BOARD (802.11b+g) INTEL KI.CAX01.005 12 LAUNCH BOARD 55.T50V7.
31 TOUCH PAD BOARD 55.T50V7.002 N/S FFC CABLE - TP/B TO MB 50.T50V7.001 N/S MODEM CABLE 50.T50V7.002 N/S POWER CORD US (3 PIN) 27.A03V7.001 POWER CORD PRC (3 PIN) 27.A03V7.003 POWER CORD KOERA ( Pin) 27.T23V7.006 POWER CORD EU (3 PIN) 27.A03V7.002 POWER CORD UK (3 PIN) 27.A03V7.004 POWER CORD ITALIAN (3 PIN) 27.A03V7.005 POWER CORD- SWISS 27.A03V7.007 POWER CORD AU (3 PIN) 27.A03V7.008 POWER CORD DANISH (3 PIN) 27.A03V7.006 POWER CORD AF (3 PIN) 27.T48V7.
37 I/O BEZEL 42.T51V7.001 23 DIMM/WIRELESS COVER 42.T50V7.002 22 HEATSINK COVER 42.T50V7.003 26 HDD COVER 42.T50V7.004 N/S 3 IN 1 DUMMY COVER 42.T51V7.002 Note: The location of 3 in 1 dummy cover is the same as 3 in 1 cover’s location. 36 3 IN 1 COVER 42.T50V7.005 25 HDD BRACKET 33.T50V7.
N/S WIRELESS LAN ANTENNA 50.T50V7.003 N/S INTEL PENTIUM M 1.5G 2M 400FSB uFCPGA2 SL6F9 B-1 STEPPING KC.N0001.715 INTEL PENTIUM M 1.6G 2M 400FSB uFCPGA2 SL7EG B-1 STEPPING KC.N0001.725 INTEL PENTIUM M 1.7G 2M 400FSB uFCPGA2 SL7EP B-1 STEPPING KC.N0001.735 INTEL PENTIUM M 1.8G 2M 400FSB uFCPGA2 SL7EN B-1 STEPPING KC.N0001.745 INTEL PENTIUM M 2.0G 2M 400FSB uFCPGA2 SL7EM B-1 STEPPING KC.N0001.755 N/S DVD/CDRW COMBO MODULE 24X QSI SBW-242C 6M.T51V7.
DVD DUAL MODULE QSI SDW-042 6M.T51V7.003 DVD DUAL DRIVE QSI SDW-042 KU.00403.001 OPTICAL DEVICE HOLDER-FIX 42.T51V7.003 DVD DUAL BEZEL FOR QSI 42.T50V7.010 DVD DUAL MODULE PIONEER DVRK14RA 6M.T51V7.004 DVD DUAL DRIVE PIONEER DVRK14RA KU.00805.001 OPTICAL DEVICE HOLDER-FIX 42.T51V7.003 DVD DUAL BEZEL FOR PIONEER 42.T50V7.011 DVD DUAL MODULE LITE-ON SOSW-852S 6M.T51V7.005 DVD DUAL DRIVE LITE-ON SOSW852S KU.00805.001 OPTICAL DEVICE HOLDER-FIX 42.T51V7.003 DVD DUAL BEZEL FOR LITE-ON 42.
Toshiba PLUTO 40G 4200rpm MK4025GAS ,KA100A F/W:KA100A KH.04004.002 SEAGATE 40G 4200rpm ST94019A, 2MB F/W:3.05 KH.04001.010 HGST 60G 4200rpm MORAGA IC25N060ATMR04-0 08K0634 F/ W:AD4A KH.06007.006 Toshiba PLUTO 60G 4200rpm MK6025GAS (phase in Mar/Apr) F/ W:KA200A KH.06004.003 HGST 80G 4200rpm MORAGA IC25N080ATMR04-0 08K635 F/ W:AD4A KH.08007.007 TOSHIBA PLUTO 80G 4200rpm MK8025GAS, 8MB F/W:KA023A KH.08004.001 AS1680/AS1410 KEYBOARD DARFON US International KB.A2707.
AS1680/AS1410 KEYBOARD DARFON Norway KB.A2707.018 AS1680/AS1410 KEYBOARD DARFON Danish KB.A2707.019 AS1680/AS1410 KEYBOARD DARFON Turkish KB.A2707.020 AS1680/AS1410 KEYBOARD DARFON Canadian French KB.A2707.021 AS1680/AS1410 KEYBOARD DARFON Japanese KB.A2707.022 AS1680/AS1410 KEYBOARD DARFON Greek KB.A2707.023 AS1680/AS1410 KEYBOARD DARFON Hebrew KB.A2707.024 AS1680/AS1410 KEYBOARD DARFON Russian KB.A2707.025 N/S LCD MODULE 15 IN. XGA AU B150XG01 6M.A27V7.
103 18 LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002 19 LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003 38 LCD PANEL W/LOGO ANTENNA 14/ 15 IN. 60.A27V7.002 20 LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004 LCD MODULE 15 IN. XGA QDI QDI150XL06-01 6M.A27V7.002 LCD 15 IN. XGA QDI QDI150XL06-01 LK.15009.002 LCD INVERTER BOARD 19.T50V7.001 LCD CABLE - 15 IN. XGA 50.T50V7.004 LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002 LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003 LCD PANEL W/LOGO ANTENNA 14/ 15 IN.
LCD PANEL W/LOGO ANTENNA 14/ 15 IN. 60.A27V7.002 LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004 LCD MODULE 15 IN. XGA SAMSUNG LTN150XB-L03 6M.A27V7.004 LCD 15 IN. XGA SAMSUNG LTN150XB-L03 LK.15006.004 LCD INVERTER BOARD 19.T50V7.001 LCD CABLE - 15 IN. XGA 50.T50V7.004 LCD BRACKET W/HINGE 15 IN. - L 33.T50V7.002 LCD BRACKET W/HINGE 15 IN. - R 33.T50V7.003 LCD PANEL W/LOGO ANTENNA 14/ 15 IN. 60.A27V7.002 LCD BEZEL W/RUBBER PAD 15 IN. 60.T50V7.004 LCD MODULE 15 IN.
MAINBOARD 855GME UMA 3 IN 1 W/PCMCIA SLOT W/O CPU MEMORY LB.A2806.001 256MB NANYA SO-DIMM DDR333 256MB NT256D64SH8BAGM-6K (.14u) KN.25603.009 256M Infineon SO-DIMM DDR333 HYS64D32020GDL-6-C (.11u/B) (Sample April/M, 09/04' by firm PO) KN.25602.022 256M Infineon SO-DIMM DDR333 256MB HYS64D32020HDL-6-C 32x64 (.11u/G) (MP in Sept.) KN.25602.012 256M Micron SO-DIMM DDR333 256MB MT4VDDT3264HG-335C2 KN.25604.016 256M Samsung SO-DIMM DDR333 256MB M470L3224FT0-CB3 (.13u) KN.2560B.
N/S LCD SCREW RUBBER PAD 47.T50V7.003 32 LCD BEZEL RUBBER PAD 47.T50V7.004 N/S SCREW M2.0X3.0-I-NI-NYLOK 86.A03V7.012 C SCREW I2.5*3M-BNIH(M2.5L3) 86.T25V7.012 N/S SCREW M2.5*4L-BZN-NYLOK 86.A03V7.006 N/S SCREW M2.0X5-I-NI-NYLOK 86.T23V7.006 D SCREW MM25060IL69 86.A08V7.004 N/S SCREW M2.0*5-I(NI)(NYLOK) 86.T23V7.010 K SCREW M2.0X2.5-I-NI-NYLOK 86.A03V7.007 G SCREW I2*3M-NIHY (M2L3) 86.T25V7.008 I SCREW M1.7*3.0-I (BK) 86.T50V7.001 A SCREW I3*3.5M-NIH(M3L3.5) 86.A03V7.
107 Chapter 6
Appendix A Model Definition and Configuration Model Name Definition Aspire 1680 Model Name Definition Model Number CPU 1681WLCi 15.4" WXGA PM 715 (1.5GHz/2M) DDR333 1x256MB 60GB 24x Combo 11b/g XPH 1681WLMi 15.4" WXGA PM 715 (1.5GHz/2M) DDR333 1x256MB 60GB 4x DVDDual 11b/g XPH 1682WLMi 15.4" WXGA PM 725 (1.6GHz/2M) DDR333 2x256MB 80GB 4x DVDDual 11b/g XPH 1681WFLMi 15.4" WXGA PM 715 (1.5GHz/2M) DDR333 1x256MB 60GB 4x DVDDual 11b/g IBM DOS 1681WFLCi 15.4" WXGA PM 715 (1.
109 Appendix A
Appendix B Test Compatible Components This computer’s compatibility is a test plan released by Acer Internal Testing Department. The test report is NOT ready as the service guide released. Once the final report is available, this chapter will be revised accordingly.
Microsoft Windows XP Environment Test Item Processor Specifications Intel Celeron 1.3GHz Intel Celeron 1.4GHz Intel PMP 705Banias 1.5 GHz, Tj85 Intel Dothan 715/1.5GHz Intel Dothan 725/1.6GHz Intel Dothan 735/1.7GHz Intel Dothan 745/1.8GHz Intel Dothan 755/2.
Item Hard Disk Drive Specifications 30G HGST Moraga+ HTS424030M9AT00 30G Toshiba MK3025GAS30GB 30G Seagate 30G ST93015A 40G HGST Moraga+ HTS424040M9AT0040GB 40G Toshiba PLUTO MK4025GAS 40G SEAGATE ST94019A40G 60G HGST Moraga IC25N060ATMR04-0 60G TOSHIBA Neptune MK6021GAS 80G HGST Moraga IC25N080ATMR04 80G TOSHIBA Pluto MK8025GAS DVD-ROM Drive 8X DVD/CD-RW Combo DVD-ROM QSI SDR-083 KME UJDA-760 QSI SBW-242C DVD-dual DVR-K14RA Lite-on SOSW-852S QSI SDW-042 QSI SDW-082 DVD-Super Multi KME UJ-830B HLDS G
Item ISDN Specifications US Robotics Megahertz 128K ISDN Card 405R17T7117M IBM OBI International ISDN PC Card I/O Peripheral I/O - Display Acer 211c 21” Viewsonic PF790 19” Acer FP751 17” TFT LCD IBM Color TFT LCD 14” Compaq Color Monitor NET Color Monitor 20” Mozo 17” TFT LCD (DVI) I/O - Projector NEC MultiSync MT-1040 I/O - Legacy (Parallel) Printer/ Scanner Canon BJC-600J Epson Stylus Color 740 Parallel Interface HP DeskJet 890C HP DeskJet 880C Parallel Interface HP LaserJet 6MP HP LaserJet 2200
Item I/O - USB Camera Specifications Intel Easy PC Camera Logitech QuickCam Express Internet Logitech QuickCam Home PC Video Camera Orange Micro USB 2.0 Web Cam I/O - USB Storage Drive Logitech CDRW +DVDROM combo USB interface Iomega USB Zip 250MB I/O-USB Flash Drive IBM 32MB USB Memory key Apacer USB Handy Drive 32MB Apacer USB Handy Drive 256MB I/O - USB Hub Belkin 4 Port USB Hub Eizo I Station USB Hub Elecom USB Hub 4 Port Sanwa USB Hub 4 Port 4 Port Hub USB 2.0 I/O - Access Point (802.
115 Appendix B
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
117 Appendix C
Index A External CD-ROM Drive Check 69 AFLASH Utility 49 F Audio 29 Features 1 B Flash Utility 49 Floppy Disk Battery Pack 55 removing the 64 BIOS 25 package 25 password control 25 ROM size 25 ROM type 25 vendor 25 Version 25 BIOS Setup Utility 36 BIOS Supports protocol 25 FRU (Field Replaceable Unit) List 94 H Hard disk 27 HDD 27 Hot Keys 15 I BIOS Utility 36 Basic System Settings 41 Navigating 37 Onboard Device Configuration 44 Startup Configuration 43 System Security 48 Indicators 13 Interm
Processor 25 S Second Level Cache 25 System Check Procedures 69 System Diagnostic Diskette 49 System Memory 25 System Utility Diskette 49 T Touchpad Check 72 U Undetermined Problems 82 USB 30 utility BIOS 36 V Video 29 W Windows XP Environment Test 111 119 Index
