F900 Smartphone Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on the F900 smartphone service guide.
Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine. These LOCALIZED FEATURES will NOT be covered in this generic service guide.
VI
Table of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Your Acer Smartphone tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Replacing the Back Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Replacing the Mini-SD Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Replacing the Stylus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Diagnostics and Troubleshooting 1 Using DebugSwitcher Function Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 1 System Specifications Features Below is a brief summary of the smartphone’s many features: Operating System • Windows Mobile® 6.1 Professional for Pocket PC Phone Edition Processor • Samsung SC3 6410, 533 MHz with one DRAM Memory • 256 MB Flash ROM, 128 MB SDRAM Display • 3.8", 800 x 480 (VGA), 65,536 colors, TFT-LCD touch panel/window Dimensions and Weight • 117.5 (L) x 63.5 (W) x 12.
Camera • Built-in 3 mega pixels auto-focus CMOS camera with flashlight, up to 2048 x 1536 resolution • VGA resolution fixed-focus CMOS camera for video telephony usage Light sensor • Sensing the brightness of environment to adjust panel luminance • Composite TV out • FM 76 ~ 108MHz, support Channel Search TV-out Radio Expansion Options • MicroSD card slot Interface/Audio • Built-in microphone and speaker, hands-free mode supported Interface/Data • Mini USB Sync Ergonomic Design • Touch pa
• Pocket PC usage: 15 hours • GPS usage: 5 hours Software (pre-loaded*) • Windows Mobile@ 6.
System Block Diagram MIC Sharp 3.
Your Acer Smartphone tour After examining your smartphone features, let us show you around your new smartphone. Views No. Item Description 1 Mini USB connector Connect to a USB cable/headphones/ charger. 2 Power button Press to turn the screen on/off or enter sleep mode; press and hold to turn the smartphone off. 3 Bluetooth/WLAN/ GPS indicator Indicates Bluetooth, WLAN and GPS status. 4 Light sensor Senses ambient light to adjust screen brightness for comfortable viewing.
No. Item Description 15 Action key Press to activate the selected menu item. 16 Volume down Press to reduce phone volume. 17 Micro SD card slot Expand your device’s memory capacity. 18 Reset pinhole Insert the stylus into this hole to reset the device. 19 Camera button Activate the camera or take a picture. Press down halfway to autofocus. 20 Flash Used to illuminate an object when taking photos in low-light conditions. 21 Camera A 3.
System Memory Item Specification Memory controller On Board Memory size 256 MB Flash ROM, 128 MB SDRAM TFT 3.
Bluetooth Item Specification Type Bluetooth 2.0, class 2 + EDR Interface UART Profiles Generic, Serial, FTP, A2DP, Headset, Hands Free FM Radio Item Specification Frequency 76 ~ 108MHz Channel Search Yes Audio Mute Yes RDS Supported Yes Antenna External (by Headset) Battery Item Specification Vendor & model name Welldone US454261 A8T Battery Type Lithium-ion Polymer Rating 3.7 VDC Maximum Charging Voltage 4.
Chapter 2 Software Upgrades System Requirements • Microsoft® Windows XP or above • Latest version of EUU (End-user Upgrade Utility / EUU_xxx.exe) or Bin files for x960 • Latest version of ActiveSync v4.5 or above • Tool: USB Cable NOTE: E-ten releases both EUU and Bin file for an authorized Service Center. Distributors and local service agent only receive EUU software. Mode Switching Performing a Soft Reset 1. Press and hold the POWER button. 2.
Using the EUU (For distributor or service center) 1. Execute ActiveSync. 2. Connect with PC. 3. Execute EUU_xxx.exe The Welcome screen displays. 4. Click Next. When EUU is installed, the Completed screen displays. 5. Click Finish. The End User Update utility starts and the following screen displays.
6. Follow the on screen instructions. When the ActiveSync connection is established, click Next.
The following screen displays. 7. When the device enters Download mode (as described on screen) click Next. NOTE: If the device does not enter Download mode, contact the service center. The following screen displays. 8. Click Update to begin receiving data. NOTE: If the Update button is disabled, disconnect and reconnect the USB cable between the device and host computer. 9. Once the data is downloaded, the Update button is replaced with a Next button. 10. Click Next to continue.
A progress screen displays. The update is complete when the following screen displays. 12. Click Finish to complete the process.
6
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble and reassemble the smartphone for maintenance and troubleshooting. IMPORTANT:The use of metal tools during disassembly may damage the casing. Use plastic tools where possible. IMPORTANT:Cover the work area with a clean, dry, lint-free cloth before placing the smartphone face down.
External Module Disassembly Process External Modules Disassembly Flowchart Turn off system power Disconnect USB and all other cables from system Remove Stylus Remove Back Cover Remove Mini SD Card Remove Battery Remove SIM Card NOTE: Items enclosed with broken lines (— - - —) are optional and may not be present.
Removing the Stylus 1. Grasp the Stylus as shown and pull to remove it from the smartphone. 2. Continue to pull the Stylus until it is completely removed from the smartphone.
Removing the Mini-SD Card NOTE: The Mini SD Card is an optional item and may not be present. 4 1. Insert a finger nail (or plastic pry) into the casing and open the Mini SD door as shown. 2. Rotate the Mini SD door away from the card slot as shown. 3. Press the Mini SD card into the slot and release. The card ejects automatically.
4. Remove the card from the slot and replace the Mini SD door.
Removing the Back Cover IMPORTANT:Cover the work area with a clean, dry, lint-free cloth before placing the smartphone face down. 6 1. Press the two cover securing latches inward as shown. 2. Rotate the Back Cover away from the smartphone to remove it.
Removing the Battery IMPORTANT:The Battery is locked in place; do not force the Battery out of the battery bay before open in the locking mechanism. 1. See “Removing the Back Cover” on page 6. 2. Slide the Battery lock in the direction of the arrow to release the Battery. 3. Insert a thumb into the Battery cutout as shown and lift the Battery out of the battery bay.
Removing the SIM Card NOTE: The SIM Card is an optional item and may not be present. 8 1. See “Removing the Battery” on page 7. 2. Slide the SIM Card out of the SIM slot as shown. 3. Lift the SIM Card clear of the smartphone as shown.
Main Unit Disassembly Process Main Unit Disassembly Flowchart Remove External Modules before proceeding Remove Upper Cover Remove LCD Panel Remove Mainboard Remove Vibration Module Remove Receiver Module Remove SIM Board Remove Camera Shielding Remove Camera Module Remove Middle Cover Screw List Step Upper Cover Mainboard Chapter 3 Screw Quantity M1.6*5 2 M1.6*1.5 2 M1.6*2 2 M1.6*3.5 2 M1.6*5 2 Part No.
Step SIM Board 10 Screw M1.6*1.5 Quantity Part No.
Removing the Upper Cover 1. See “Removing the Battery” on page 7. 2. Remove the two rubber screw caps from the Lower Cover using tweezers. IMPORTANT:Thin tine metal tweezers can be used to remove the screw covers. Take care not to scratch the Lower Cover during removal. 3. Remove the two screws located under the rubber screw caps. Step Upper Cover Chapter 3 Screw M1.
4. Remove the two screws located on the sides of the Lower Cover. Step Upper Cover Screw M1.6*1.5 Quantity Screw Type 2 IMPORTANT:Do not force the covers apart to avoid damaging the plastic securing clips. IMPORTANT:Use a plastic pry less than or equal to 0.96 mm thickness. Metal tools may damage the covers. 12 5. Starting at the top-right edge of the smartphone, pry apart the covers. 6. Work along the top edge of the cover as shown, gently prying the covers apart.
7. Work down the right side of the cover as shown, prying the covers apart. 8. Repeat the process down the left side, gradually prying apart the covers.
9. Apply lateral pressure as indicated by the arrow (1) and pry apart the bottom right edge of the Upper Cover (2). 1 2 10. Work along the bottom edge prying the covers apart as shown. IMPORTANT:Do not remove the Upper Cover completely; the TouchPad FFC is still connected at this stage. 11. Lift the Upper Cover away from the Lower Cover and turn it over to expose the TouchPad FFC.
12. Using plastic tweezers, lift the FFC connector to disconnect the Upper Cover from the Mainboard. 13. Remove the Upper Cover from the Lower Cover and place it on a clean, dry, lint-free cloth. 14. The Lower and Upper Covers appear as shown below when separated. IMPORTANT:Ensure that no dust, dirt, or finger prints come in to contact with the exposed LCD Panel or Front Cover; Foreign particles and grease will affect LCD output performance.
Removing the LCD Module IMPORTANT:Ensure that no dust, dirt, or finger prints come in to contact with the exposed LCD Panel or Front Cover; Foreign particles and grease will affect LCD output performance. 1. See “Removing the Upper Cover” on page 11. IMPORTANT:The LCD Panel is not secured to the Lower Cover. Support the panel before turning the Lower over. 2. Turn the smartphone over to release the LCD Panel from the Lower Cover.
Chapter 3 17
Removing the Mainboard 1. See “Removing the LCD Module” on page 16. 2. Turn the smartphone over. Remove the two screws securing the Mainboard to the Lower Cover. Step Mainboard 3. 18 Screw M1.6*2 Quantity Screw Type 2 Turn the smartphone over. Peel back the barcode to expose the securing screw.
4. Remove the four screws securing the Mainboard to the Lower Cover. Step Screw Quantity Mainboard (red callout) M1.6*3.5 2 Mainboard (green callout) M1.6*5 2 5. Remove the rubber protector from the Microphone as shown. 6.
7. Grasp the Lower Cover as shown (1). Lift and rotate the Mainboard out of the Lower Cover (2) to clear the I/O ports (green callout).
Removing the Vibration Module 1. See “Removing the Mainboard” on page 18. 2. Using the tweezers, grasp the Vibration Module and lift it clear of the Lower Cover. 3. Ensure that the rubber insulation lifts free along with the Vibration Module.
Removing the Receiver Module 22 1. See “Removing the Mainboard” on page 18. 2. Locate the removal tab as shown. 3. Press the removal tab toward the outside of the Lower Cover. The Receiver Module top edge lifts out of the Lower Cover. 4. Lift the Receiver clear of the Lower Cover.
Removing the SIM Board 1. See “Removing the Mainboard” on page 18. 2. Remove the two screws securing the SIM Board to the Mainboard. Step SIM Board Screw M1.6*1.5 Quantity Screw Type 2 IMPORTANT:Do not remove the SIM Board completely; the SIM FFC is still connected at this stage. 3. Lift the SIM Board away from the Mainboard as shown. 4. Disconnect the SIM Board FFC from the Mainboard.
5. 24 Disconnect the FFC from the SIM Board.
Removing the Camera Shielding 1. See “Removing the SIM Board” on page 23. 2. Insert thin tine tweezers either side of the Shielding securing clip and gently pry the Shielding away from the Mainboard. NOTE: When removing the Shielding, it may be necessary to loosen the securing clip on the opposite side of the module to release it from the Mainboard 3. Lift the Shielding clear of the Mainboard to expose the Camera Module.
Removing the Camera Module 1. See “Removing the Camera Shielding” on page 25. IMPORTANT:Do not disconnect the Camera Module by lifting the lens directly. Use tweezers to disconnect the interface to avoid damaging the camera FFC. 26 2. Remove the adhesive tape securing the Camera FFC in place. 3. Using the tweezers, pry up the FFC connector to disconnect the FFC. 4. Lift the Camera Module and push the FFC cable through the Middle Cover to remove the Camera Module.
Removing the Middle Cover 1. See “Removing the Camera Module” on page 26. 2. Locate the four clips securing the Middle Cover to the Mainboard. D C A B 3. Release clip A by pushing it away from the Mainboard as shown. 4. Release clip B by pushing it away from the Mainboard as shown.
5. Release clip C by pushing it away from the Mainboard as shown. 6. Lift the Mainboard away from the Middle Cover as shown, and slide the Mainboard clear of the clip D. Replacing Internal Module Components Replacing the Middle Cover 1. 28 Four clips secure the Middle Cover to the Main Board as shown below. Insert the main board into the Middle cover so the clips (denoted by circles) and the pins (denoted by arrows) are aligned.
D D C A A B 1. C B Insert clip A and the nearby pin by pushing it into from the Mainboard as shown.
30 2. Insert clip B and the nearby pin by pushing it into the Mainboard as shown. 3. Insert clip C and the nearby pin by pushing it into the Mainboard as shown. Take care the pin is properly mounted as it is hidden under the USB port after connection. 4. Insert clip D and the nearby pin by pushing it into the Mainboard as shown.
Replacing the Camera Module 1. Push the FFC cable through the slot in the side of the Middle Cover camera well. 2. Slide the camera into the camera well in the middle cover. 3. Connect the FFC as shown. 4. Reapply the adhesive tape to secure the Camera FFC in place.
Replacing the Camera Shielding 1. Slide the camera shield over the camera well on the middle board. 2. Push the tabs down to be sure that the securing clips on the camera well are inserted into the shielding. Replacing the SIM Board 1. Connect the FFC to the SIM Board. IMPORTANT:Be sure that the end of the FFC connector with the white stripe is connected to the SIM Board.
2. Connect the SIM Board FFC from the Mainboard. 3. Lift the SIM Board away from the Mainboard as shown. 4. Insert the two screws to secure the SIM Board to the Mainboard. Step SIM Board Chapter 3 Screw M1.6*1.
Replacing the Receiver Module 1. Insert the receiver module into the Lower Cover and ensure the clips snap into place. Replacing the Vibration Module 34 1. Grasping the Vibration Module firmly from both sides, insert the Vibration Module into the vibration module well in the Lower Cover. 2. Press the vibration module into place until the edges are flush with the well.
Replacing the Mainboard 1. Insert the Mainboard into the Lower Cover as shown. The I/O port and green tab on the main board should be inserted fully into the main board, then drop the side with the SD card reader into place. make sure that all screw holes align. 2. Insert the rubber protector for the Microphone as shown. 3.
4. Replace the four screws to secure the Mainboard to the Lower Cover. Step Screw Mainboard (red callout) M1.6*3.5 2 Mainboard (green callout) M1.6*5 2 5. Screw Type Turn the smartphone over. Insert the two screws to secure the Mainboard to the Lower Cover. Step Mainboard 36 Quantity Screw M1.
Replacing the LCD Module 1. Reapply the adhesive to the LCD FFC Cable as shown. 2. Reconnect the LCD FFC to the main board as shown. 3. Reapply the adhesive LCD gasket.
4. Insert the LCD Panel into the middle cover. Replacing the Upper Cover 38 1. Connect the screen FFC to the Mainboard. 2. Align the cover tabs and slide the tabs into the slots in the lower cover assembly.
3. Press the bottom of the covers together, starting with one side and moving to the other. 4. Using a pinching motion, press the edges of the covers together, working from the base of the unit to the top. Attach one side at a time. 5. Pinch the top edge together.
6. Insert the two screws located on the sides of the Lower Cover. Step Upper Cover 7. Screw M1.6*1.5 Screw Type Quantity Screw Type 2 Insert the two screws into the back of the unit. Step Upper Cover 8. Quantity Screw M1.6*5 2 Insert the two rubber screw caps into the Lower Cover. Replacing Internal Module Components Replacing the SIM Card 1. 40 Slide the SIM Card into the SIM slot as shown.
Replacing the Battery 1. Insert the Battery into the battery bay. 2. Slide the Battery lock in the direction of the arrow to lock the Battery in place. Replacing the Back Cover 1. Insert the bottom of the Back Cover into the smartphone.
2. Push the back cover into place. Replacing the Mini-SD Card 1. 42 Insert the card into the slot until it clicks into place.
2. Rotate the Mini SD door towards the card slot as shown. 3. Push the door into the case to secure it in place. Replacing the Stylus 1. Push the stylus into the stylus holder in the base of the smartphone as shown.
44 Chapter 3
Chapter 4 Diagnostics and Troubleshooting Using DebugSwitcher Function Testing RUN IN and Discharge Tests NOTE: • Wear anti-static gloves. 1. Insert the battery, battery cover and charger in to the handset and power on. 2. Tap LED and wait for the keypad LED to light. Tap OK to test. 3. Tap BurnIn Test for Run in testing. 4. When the screen shows PASS the handset has passed all tests, 5. Check if the handset LED always lights green. If yes, handset passed. 6.
FM Receiver, Audio and GPS1 Tests NOTE: • 2 Take care not to damage the casing when putting the handset on the test fixture. 1. Plug in the FM Receiver test cable into the handset USB port and press FM Rx test. If the test shows Pass, the handset passed. 2. If the test is Pass, put the handset in the tray and click GPS for GPS testing. If the test shows Pass, the handset passed. 3. Put the handset in the Audio Test fixture and click 1K Hz to test Audio functions. 4.
Camera Test NOTE: • Wear anti-static gloves. • Take care not to damage the casing when putting the device on the test fixture. • Make sure that the handset camera can auto-focus. 1. Tap CMR to begin testing. 2. Hold the handset at 3m to test focus functionality. Check for color shifts, blurring, and distortion. If there is no issue, the handset passed. 3. Repeat step 2 using a sheet of white paper with a single black dot in the centre to confirm the camera test.
Function Testing 1 NOTE: • Wear anti-static gloves. 1. Tap Seq Test to begin testing functions. 2. The LCD Test starts. Tap the screen to cycle through white, black, red, green, and blue backgrounds. • Check that the white screen displays no black dots. • Check that the black screen displays no white dots. • Check that the RGB screens display with no color distortion or bleeding. 3. Tap OK if the test is passed. 4. Tap the screen to test the Backlight function. 5.
12. Tap the screen to test the Vibration function. 13. Tap ON and OFF to test the funtionality. Ensure that the vibration is not too strong or too weak, and noise-less. 14. Tap OK if the test is passed.
Function Testing 2 NOTE: • Wear anti-static gloves. • When testing the touch panel pen, draw from corner to corner and side to side. Do not start in the centre of the screen. 1. Tap the screen to test the various key/button functions. 2. Tap the keys shown in the image to test the funtionality. Ensure that the keys are not loose or unresponsive. 3. Tap OK if the test is passed. 4. Tap the screen to perform the PenTrac test. 5. Draw a star as shown to test the full extent of the touchpad. 6.
G Sensor and Light Sensor Tests NOTE: • Wear anti-static gloves. • Take care not to damage the casing when putting the device on the test fixture. • Ensure the Light Sensor Test Fixture timer is reset to 0 (zero) before use. • Please use the Golden Sample to calibrate tests before use. 1. Press OK to start the G Sensor Test. 2. Tap Start to begin the test. 3. The screen shows Z, -Z, X, -X, Y, and -Y on the screen.
TV-out and GPS2 Test NOTE: • 8 Wear anti-static gloves. 1. Assembly the battery then power on. 2. Press the TV Out tab to test TV-Out function. 3. Make sure that the speaker generates Left, Right, and Centre channel output. Check if the monitor displays TV-output handset signal. If so, the device passed the test. 4. Scan bar code of the device with a barcode reader. 5. Plug in a USB cable to the handset then put in the test fixture for testing. 6.
Using the Windows Mobile Test System Testing Item Phone Live Test Procedure Test phone dial and receive function: 1. Device over device to testing Guidelines Check Dial/Answer the phone call's voice is clear enough 2. Use wired Headset to answer call 3. Use Bluetooth headset to answer call USB connection Synchronize PDA with PC Camera with Micro SD card Read/Write Test • Snap shot a photo then delete it • Save the file in Micro SD card WiFi Test 1.
10 Chapter 4
Chapter 5 Serial Number Definition The following information describes the serial number details available on the Acer product sticker. To view the serial number, remove the Back Cover and Battery (see “Disassembly Process” on page 1) as shown below: FCC ID: SPUF900 Made in Taiwan Use appropriately for effect of electromagnetic wave. Model No.: F900 Part No.: ETL1307152 Series No.
Acer SNID YWWddddddMM Code Description YWW 3 digit numeric year and week code (as above) dddddd 6 digit unique number derived from Acer 22 Code SN (SSSSS) Transfer Rule: S1S2S3S4S5 dddddd = S1 * 164 + S2 * 163 + S3 * 162 + S4 * 16 + S5 For example: 001FD = 000509 (1 * 162 + 15 * 16 + 13) MM 2 Manufacturer code (as above)
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of the F900 smartphone. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. If for whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
F900 Smartphone Exploded Diagram 1 8 2 9 3 10 4 11 5 6 12 7 Item 1 2 Description Touchscreen Part Number 60.H420S.
Item Chapter 6 Description Part Number 2 LCD Module 6M.H420S.001 3 Mainboard MB.H4200.001 4 Vibration Module 60.H420S.001 5 Receiver 60.H420S.002 6 Back Cover 60.H420S.005 7 Battery Cover 60.H420S.010 8 Front Cover 60.H420S.004 9 Middle Cover 60.H420S.007 10 Camera QM.03M02.001 11 Camera Shield 60.H420S.008 12 Battery BT.0010T.
F900 Smartphone FRU List Acer P/N ACCESSORY USB CABLE 6K.H370S.001 STYLUS.F900 6K.H420S.001 STYLUS WITH BAG PACKING.F900 6K.H420S.002 LEATHER POUCH.F900 6K.H420S.003 PU POUCH.F900 6K.H430S.003 ADAPTER AP.0050P.001 AC ADAPTER EU-PLUG AP.0050P.002 AC ADAPTER UK-PLUG AP.0050P.003 AC ADAPTER US-PLUG AP.0050P.004 AC ADAPTER AU-PLUG AP.0050P.005 HEADSET.F900 QH.00205.003 BATTERY.F900 BT.0010T.003 DUMMY BATTERY.F900 6K.H420S.004 M/B F900 MB.H4200.001 BOARD SIM BOARD.
Acer P/N RECEIVER.F900 60.H420S.002 SPEAKER.F900 60.H420S.003 FRONT COVER ASSY.F900 60.H420S.004 REAR COVER ASSY.F900 60.H420S.005 ANTENNA (GSM/DCS/PCS/WCDMA)+FPC TYPE 60.H420S.006 LCM FRAME 60.H420S.007 SHIELD COVER FOR 3M CAMERA 60.H420S.008 HOLDER_3311_BLACK_RUBBER?SILICON RU BBER_N/A_MICPHONE CAP_PMP_43001420 60.H420S.009 LCM+FPC.F900 6M.H420S.001 MYLAR FOR CAMERA B TO B CONN 47.H420S.002 GASKET FOR EMP COVER 47.H420S.003 REGULATION LABEL_ F900 (FOR TW & HK ONLY) 47.H420S.
Acer P/N OPTICAL DEVICE CAMERA.F900 QM.03M02.001 MACHINE SCREW_FLAT_CROSS(JCIS)_1.6M M_1.5MM_BLACK_STEEL_PLATING ZINC_HNS _NYLOK.44001480 86.H420S.001 MACHINE SCREW_FLAT_TORX_1.6MM_5MM_ BLACK_STEEL_PLATING ZINC_HNS_T5.NYLO K.44001510 86.H420S.002 MACHINE SCREW_FLAT_CROSS(JCIS)_1.6M M_2MM_BLACK_STEEL_PLATING NICKEL_HN S_NYLOK.44001490 86.H420S.003 MACHINE SCREW_FLAT_TORX_1.6MM_3.5MM _SILVER_STEEL_PLATING NICKEL_HNS_NYL OK 86.H420S.
Appendix A Online Support Information This section describes online technical support services available to help you repair your Acer device. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
2 Appendix A
Index B R Back Cover Receiver Module Removing 6 Replacing 41 Removing 22 Replacing 34 Battery S Removing 7 Replacing 41 SIM Board Removing 23 Replacing 32 C Camera Module SIM Card Removing 26 Replacing 31 Removing 8 Replacing 40 Camera Shielding Stylus Removing 25 Replacing 32 Removing 3 Replacing 43 System D Block Diagram Display 4 4 U E Upper Cover Removing 11 Replacing 38 External Module Disassembly Flowchart 2 V F Features Vibration Module 1 FRU (Field Replaceable Unit)
2