Ferrari one Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
PRINTED IN TAIWAN ii
Revision History Please refer to the table below for the updates made on this service guide.
Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. vi 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
Table of Contents System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Your Notebook Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Removing the Button Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 Removing the Bluetooth Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Removing the I/O Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Removing the LCD Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69 Removing the Mainboard . . . . . . . . . . . . . . . . . . . .
Table of Contents HDD Not Operating Correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .136 USB Failure (Right up/down side) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Other Failures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137 Intermittent Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .138 Undetermined Problems . . . . . . . . . .
Table of Contents x
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many features: Operating System • Genuine Windows 7 Platform • AMD Athlon™ 64 X2 dual-core processor • AMD M780G Chipset System Memory • Dual-Channel SDRAM support • Up to 2 GB of DDR2 667 MHz memory, upgradeable to 4 GB using two soDIMM modules • Up to 2 GB of DDR2 800 MHz memory, upgradeable to 4 GB using two soDIMM modules Display and graphics • 16:9 aspect ratio • 11.
• Acer InviLink™ 802.11b/g* • WPAN: Bluetooth® 2.1+Enhanced Data Rate (EDR) • LAN: Gigabit Ethernet; Wake-on-LAN ready Privacy control • BIOS user, supervisor, HDD passwords • Kensington lock slot Dimensions and Weight) • 285 (W) x 204 (D) x 24/30 (H) mm (11.22 x 8.03 x 0.9/1.2 inches) • 1.5 kg (3.31 lbs.) with 6-cell Li-ion battery pack Power subsystem • ACPI 3.
System Block Diagram Chapter 1 3
Your Notebook Tour This section provides an overview of the features and functions of the notebook. Front View 1 2 3 4 10 5 6 9 8 7 No. 1 Item Acer Crystal Eye webcam Description Web camera for video communication. 2 Microphone Internal microphone for sound recording. 3 Display screen Also called Liquid-Crystal Display (LCD), displays computer output (Configuration may vary by models). 4 HDD Indicates when the hard disk drive is active. Num Lock Lights up when Num Lock is activated.
No. Icon Item Description 6 Touchpad Touch-sensitive pointing device which functions like a computer mouse. 7 Click buttons (left and right) The left and right buttons function like the left and right mouse buttons. 8 Communication indicator Indicates the status of WLAN / 3G communication. (only for certain models) Power Indicates the computer's power status. Battery Indicates the computer's battery status. 1. Charging: The light shows amber when the battery is charging. 2.
Left View 1 No. 2 Icon 4 3 Item Description 1 External display (VGA) port Connects to a display device (e.g., external monitor, LCD projector). 2 Acer DynaVivid Graphics Dock connector Connects to an Acer DynaVivid Graphics Dock device. 3 Ventilation slots Enable the computer to stay cool, even after prolonged use. 4 USB 2.0 port Connect to USB 2.0 devices (e.g., USB mouse, USB camera). Right View 1 No.
5 Kensington lock Connects to a Kensington-compatible computer security lock. Note: Wrap the computer security lock cable around an immovable object such as a table or handle of a locked drawer. Insert the lock into the notch and turn the key to secure the lock. Some keyless models are also available. 6 Ethernet (RJ-45) port Connects to an Ethernet 10/100/1000- based network. Base View 1 2 6 3 5 4 No. Icon Item Description 1 Battery bay Houses the computer's battery pack.
Rear View 1 No. Icon Item 1 Battery Description Houses the computer's battery pack. Indicators The computer has several easy-to-read status indicators. The battery indicator is visible even when the computer cover is closed. Icon Function Description Bluetooth Indicates the status of Bluetooth communication. Wireless LAN Indicates the status of Wireless LAN communication. 3G communication Indicates the status of 3G communication. HDD Indicates when the hard disk drive is active.
Touchpad Basics The following items show you how to use the Touchpad: 1 2 3 • Move your finger across the Touchpad (1) to move the cursor. • Press the left (2) and right (3) buttons located beneath the Touchpad to perform selection and execution functions. These two buttons are similar to the left and right buttons on a mouse. Tapping on the Touchpad is the same as clicking the left button. p Function Left Button (2) Right Button (3) Main Touchpad (1) Execute Quickly click twice.
Using the Keyboard Your computer has a close-to-full-sized keyboard and an embedded numeric keypad, separate cursor, lock, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hotkeys or key combinations to access most of the computer's controls like screen brightness and volume output. To activate hotkeys, press and hold the key before pressing the other key in the hotkey combination. Hotkey 12 Icon Function Description + Power management Launch Windows power management. + System Properties Display the System Properties dialog box.
Special Keys You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Hold and then press the <5> key at the upper-center of the keyboard. NOTE: Some fonts and software do not support the Euro symbol. See www.microsoft.com/typography/faq/ faq12.htm for more information. The US dollar sign 1. Open a text editor or word processor. 2.
Hardware Specifications and Configurations Processor Item Specification CPU type AMD L310/Dual core/1.2G CPU package 638-pin lidless micro-PGA Power • Features VCC-CORE: voltage for the future processor will depend on VID0-5 for battery mode and setting via software for adapter mode for the future processor • AMD Athlon™ 64 X2 Processor L310 • Speed: 1.
Item Features Specification • Supports the mobile and desktop Athlon 64/Athlon 64FX/ Athlon X2/AMD Sempron/AMD Turion 64 processors, including both AM2 and S1 socket CPUs. • Supports 16-bit up/down HyperTransport(HT) 3.0 interface up to 4.4GT/s. • Supports 200, 400, 600, 800 and 1000MHz HT1 frequencies. • Supports LDTSTP interface, CPU throttling and stutter mode. • Supports ATI HyperMemory™* technology. • Compliant with the PCI Express(PCI-E) Gen2 Specification.
Item Features Specification • Supports AMD Athlon 64/Athlon 64FX/Opteron/AMD Sempron/Mobile Sempron/Athlon XP-M and Turion processors, Dual-core CPUs are supported. • A-Link Express II interface to AMD Northbridges; high data transfer bandwidth(up to 2.5Gb/s / Lane) • PCI Host Bus controller • • • Supports PCI bus at 33MHz PCI Rev. 2.3 specification support Supports up to 6 bus master devices • 5 OHCI and 2 EHCI Host controllers to supports 12 USB 2.0 ports and 2 dedicated USB 1.
Item Specification Package TBC Features • Microsoft® DirectX®10 • PCI Express® 2.0 • Vari-Bright™ Technology • 12 USB 2.0 ports and two USB 1.
Item Specifications 830 Internal transfer rate (Mbits/sec, max) 1175 830 1175 875 Mbits/s maximum I/O data transfer rate (Mbytes/sec max) 845 Mbits/s maximum DC Power Requirements Voltage +5.0V ± 5%.
Item Specifications Active Area (mm) 256.125 (H) x 144.0 (V) Display resolution (pixels) 1366 x 768 Pixel Pitch (mm) 0.1875 (H) x 0.1875 (V) Typical White Luminance (cd/m ) also called Brightness 200 nit Contrast Ratio 500:1 typ Response Time (Optical Rise Time/Fall Time) msec 8 mS typ Typical Power Consumption (watt) 3.86W Weight (with inverter) 235g max. Physical Size (mm) Length: 278.5 max Width: 168 max Thickness: 3.6 Normal Input Voltage +3.
Item Features Specification • • • • • • • Headphone-out with S/PDIF, and Microphone-In. Meets performance and function requirements for Microsoft WLP 3.10, and stricter performance requirements for future WLP Two stereo DAC supports 16/20/24-bit PCM for two independent playback(multiple streaming). Two stereo ADC supports 16/20/24-bit PCM format for two independent recording. All DACs/ADCs supports independent 44.
Media Card Reader Item Specification Chipset RTS5159-GR Features • Compliant with USB Mass Storage Class Bulk only Transport Specification Rev. 1.
Wireless LAN Item Model Specification Specification Specification • Foxconn Wireless LAN Atheros HB95 1x1 BG (HM) • Foxconn Wireless LAN Atheros HB93 Protocol 802.11a/b/g Interface PCI-Express Specification 3G Module Item Specification 3G Model Foxconn Gobi2000 Technical Standard • CDMA2000 1X • CDMA2000 1xEV-DO(Release0 and Rev.
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Information The Information screen displays a summary of your computer hardware information. Information Main Security Phoenix SecureCore (tm) Setup Utility Boot Exit CPU Type CPU Speed AMD Athlon(tm) X2 Dual Core Processor L310 1200 MHz HDD Model Name: HDD Serial Number: ATAPI Model name: System BIOS Version: VGA BIOS Version: Serial Number: Asset Tag Number: Product Name: Manufacturer Name: UUID: WDC WD3200BEVT-22ZCT0 WD-WX80A7939866 F1 Help ESC Exit v0.3102 ATi 010.094.001.020.
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery. Information Main Phoenix SecureCore (tm) Setup Utility Security Boot Exit Item Specific Help System Time: System Date: [19:10:59] [06/09/2009] Total Memory: Video Memory: 3072 MB 336MB] Quick Boot Network Boot F12 Boot Menu D2D Recovery SATA Mode [Enabled] [Enabled] [Disabled] [Enabled] [AHCI Mode] F1 Help ESC Exit , , or selects field.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use. Information Main Phoenix SecureCore (tm) Setup Utility Security Boot Exit Item Specific Help Supervisor Password Is: User Password Is: HDD Password Is: Clear Clear Clear Supervisor Password controls access to the setup utility.
Setting a Password Follow these steps as you set the user or the supervisor password: 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Supervisor Password box appears: Set Supervisor Password Enter New Password Confirm New Password 2. [ [ ] ] Type a password in the “Enter New Password” field. The password length can not exceeds 8 alphanumeric characters (A-Z, a-z, 0-9, not case sensitive).
Changing a Password 1. Use the ↑ and ↓ keys to highlight the Set Supervisor Password parameter and press the Enter key. The Set Password box appears. Set Supervisor Password Enter Current Password Enter New Password Confirm New Password [ [ [ ] ] ] 2. Type the current password in the Enter Current Password field and press Enter. 3. Type a password in the Enter New Password field. Retype the password in the Confirm New Password field. 4. Press Enter.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes various USB diskette drives and the onboard hard disk drive. 1. IDE0 : WDC WD2500BEVT-22ZCT0 Information Main Phoenix SecureCore (tm) Setup Utility Security Boot Exit Item Specific Help Boot priority order: 1: 2: 3: 4: 5: 6: 7: 8: F1 Help ESC Exit Chapter 2 Keys used to view or configure devices: Up and Down arrows select a device.
Exit The Exit screen allows you to save or discard any changes you made and quit the BIOS Utility. Information Main Phoenix SecureCore (tm) Setup Utility Security Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help ESC Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: Chapter 2 • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted.
DOS Flash Utility Perform the following steps to use the DOS Flash Utility: 1. Press F2 during boot to enter the Setup Menu. 2. Select Boot Menu to modify the boot priority order, for example, if using USB HDD to Update BIOS, move USB HDD to position 1. 1. IDE0 : WDC WD2500BEVT-22ZCT0 Information Main Phoenix SecureCore (tm) Setup Utility Security Boot Exit Item Specific Help Boot priority order: 1: 2: 3: 4: 5: 6: 7: 8: F1 Help ESC Exit 3.
WinFlash Utility Perform the following steps to use the WinFlash Utility: 1. In Windows run ZH6_xxxx_win.exe where xxxx is the bios version. For example, ZH6_3102_win.exe 2. When the process is complete, close all programs and applications and reboot the system.
Remove HDD/BIOS Password Utilities This section provide you with removing HDD/BIOS method: Remove HDD Password: When the user keys in the wrong password three times, the system reports the following error code to user. To unlock the HDD password, perform the following steps: 1. Press Enter to display the Select Item screen. 2. Select Enter Unlock Password and press Enter. An Unlock Password displays. 3. Make a note of the key, 76943488 in the example. 4.
Removing BIOS Passwords: If you key in the wrong Supervisor Password three times, System Disabled displays on the screen. See the image below. 1. Make a note of the number displayed: 14452 in this instance. 2. Boot up the system to a removable bootable drive containing DOS and open a DOS prompt. For instructions on changing boot priority see “Boot” on page 29. 3. Enter the BIOS_PW.EXE command. 4. Enter bios_pw 14452 0 NOTE: 1.
Miscellaneous Utilities Using Boot Sequence Selector Boot Sequence Selector allows the boot order to be changes without accessing the BIOS. To use Boot Sequence Selector, perform the following steps: 1. Enter into DOS. 2. Execute BS.exe to display the usage screen. 3. Select the desired boot sequence by entering the corresponding sequence, for example, enter BS2 to change the boot sequence to HDD|CD ROM|LAN|Floppy.
Example 1: Read DMI Information from Memory Input: dmitools /r Output: Manufacturer (Type1, Offset04h): Acer Product Name (Type1, Offset05h): Aspire one xxxxx Serial Number (Type1, Offset07h): 01234567890123456789 UUID String (Type1, Offset08h): xxxxxxxx-xxxx-xxxx-xxxx-xxxxxxxxxxxx Asset Tag (Type3, Offset04h): Acer Asstag Example 2: Write Product Name to EEPROM Input: dmitools /wp Acer Example 3: Write Serial Number to EEPROM Input: dmitools /ws 01234567890123456789 Example 4: Write UUID to EEPROM Input
38 Chapter 2
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: • Wrist grounding strap and conductive mat for preventing electrostatic discharge • Flat screwdriver • Philips screwdriver • Plastic flat screwdriver • Plastic tweezers NOTE: The screws for the different components vary in size.
2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack. Disassembly Process The disassembly process is divided into the following sections: • External components disassembly • Main unit disassembly • LCD module disassembly The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
External Modules Disassembly Flowchart Turn off system and peripherals power Disconnect power and signal cables from system Remove Dummy Card Remove Battery Remove SIM Card Remove Lower Covers Remove HDD Remove DIMM Remove WLAN Board Remove 3G Board Screw List Step Screw Quantity Part No. HDD Module M3*3.5(silver) 4 86.TPK07.001 3G Module M2*4 1 86.W0107.003 WLAN Module M2*5 1 86.TG607.
Removing the Battery Pack 1. Turn the computer over. 2. Slide the battery lock/unlock latch to the unlock position. 3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2).
Removing the Dummy Card 1. Press the dummy card to allow it to spring out. 2. Remove the dummy card. Removing the SIM Card 1. See “Removing the Battery Pack” on page 42. 2. Press the SIM card to allow it to spring out.
3. Pull the SIM card out and store carefully. Removing the Hard Disk Drive Module 44 1. See “Removing the Battery Pack” on page 42. 2. Loosen the two (2) captive screws on the HDD Cover. 3. Remove the HDD Cover from the inside edge.
4. Grasp the black tab. 5. Lift up on the black tab to pull the HDD out but do not remove completely. Flip the HDD over to allow access to the HDD cable. CAUTION: Do not pul the HDD out before disconnecting the HDD cable. 6. Grasp the HDD cable connector tab and pull up.
7. Remove the HDD cable from the HDD. 8. Remove the four (4) screws of the HDD rails. Step HDD Disassembly 9. Screw 3*3.5 (silver) Quantity Screw Type. 4 Remove the rails from the HDD. Removing the 3G Module 1. 46 See “Removing the Battery Pack” on page 42.
2. Loosen the three (3) captive screws in the Memory Cover. 3. Lift the Memory Cover out from the rear edge. 4. Remove the cables from the 3G module.
5. Remove the one (1) screw from the 3G module. Step 3G Disassembly 6. 48 Screw 2*4 Quantity Screw Type. 1 Remove the 3G module.
Removing the DIMM Module 1. See “Removing the Battery Pack” on page 42. 2. Loosen the three (3) captive screws in the Memory Cover. 3. Remove the Memory Cover from the rear edge. 4. Pull open the two memory side clips.
50 5. Lift the memory card out. 6. Repeat steps 4) and 5) for the second memory card.
Removing the WLAN Module 1. See “Removing the Battery Pack” on page 42. 2. Loosen the two (2) captive screws in the HDD Cover. 3. Remove the HDD Cover from the inside edge. 4. Loosen the three (3) captive screws in the Memory Cover.
5. Remove the Memory Cover from the rear edge. 6. Remove the cables on the WLAN module. 7. Remove the one (1) screw on the WLAN module. Step WLAN Disassembly 52 Screw 2*5 Quantity Screw Type.
8. Remove the WLAN module.
Main Unit Disassembly Process IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position. NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration.
Screw List Step Screw Quantity Part No. Lower Cover 2*3 4 86.S0207.001 Lower Cover 2*5 1 86.TG607.004 Lower Cover 2*8 5 86.FRC07.001 Upper Cover 2.0*2.5 (silver) 1 86.TG607.004 Upper Cover 2*3 1 86.S0207.001 Upper Cover 2*5 9 86.TG607.004 Button Board M2-0.4*2 2 86.W4107.002 IO Board 2*5 1 86.TPK07.001 Main Board 2*3 1 86.S0207.001 LCD Hinge 2*5 2 86.TG607.004 Speaker Module 2*3 3 86.S0207.
Removing the Keyboard IMPORTANT: The keyboard is easily warped or damaged during the removal process. Take care not to use excessive force when removing the keyboard and replace if any damage occurs. 56 1. See “Removing the Battery Pack” on page 42. 2. Press the four (4) latches. 3. Pry up the keyboard.
4. Flip the keyboard over. 5. Unlock the keyboard cable. 6. Remove the keyboard cable and keyboard.
Removing the Upper Cover 1. See “Removing the Battery Pack” on page 42. 2. See “Removing the SIM Card” on page 43. 3. See “Removing the Hard Disk Drive Module” on page 44. 4. See “Remove the rails from the HDD.” on page 46. 5. See “Removing the DIMM Module” on page 49. 6. See “Removing the WLAN Module” on page 51. 7. See “Removing the Keyboard” on page 56. 8.
9. Turn the computer over and remove the eleven (11) screws in the upper cover. Step Upper Cover Disassembly Screw Quantity 2.0*2.5 Silver 1 (green call out) 2*3 1 (blue call out) 2*5 9 (red call out) Screw Type. 10. Unlock the I/O board to main board cable at both ends.
11. Disconnect the I/O board to main board cable at both ends. 12. Unlock and disconnect the button board to main board cable.
13. Pry up the Upper Cover starting from the side and lift away. 14. Remove the I/O board to main board cable.
Removing the Button Board IMPORTANT: The Touchpad Board cannot be removed individually. To replace the Button Board, replace the entire Upper Cover. 62 1. See “Removing the Upper Cover” on page 58. 2. Unlock the touchpad cable at both ends. 3. Remove the touchpad cable. 4. Disconnect the button board cable from the button board.
5. Pull the button board cable away from the adhesive. 6. Remove the button board cable. 7. Remove the two (2) screws of the button board. Step Button Board Disassembly Chapter 3 Screw M2-0.4*2 Quantity Screw Type.
8. 64 Lift the button board away.
Removing the Bluetooth Module 1. See “Removing the Upper Cover” on page 58. 2. Disconnect the Bluetooth module to main board cable. 3. Pull the Bluetooth module away.
Removing the I/O Board 66 1. See “Removing the Upper Cover” on page 58. 2. Open the locking latch at both ends of the card reader cable connectors. 3. Remove the card reader cable. 4. Disconnect the DC power cable connector from the mainboard.
5. Remove the tape and lift the DC cable out of the cable guide. 6. Disconnect the DC power cable from the I/O board. 7. Remove the one (1) screw in the I/O board. Step IO Board Disassembly Chapter 3 Screw 2*5 Quantity Screw Type.
8. 68 Lift the I/O board up by the inner edge and pull away on the angle.
Removing the LCD Module 1. See “Removing the Upper Cover” on page 58. 2. See “Removing the I/O Board” on page 66. 3. Lift up the LCD cable protective over. 4. Disconnect the LCD cable connector.
5. Remove the two (2) screws from the left and right hinges of the LCD module. Step LCD Disassembly Screw 2*5 Quantity Screw Type. 2 6. Lift away the LCD module and lay it down. NOTE: Lay the LCD down on a clear smooth surface to prevent damage. 70 7. Pull the antenna cables free of the chassis, threading the antenna cables through from the bottom side.. 8. Remove the LCD module completely.
Removing the Mainboard 1. See “Removing the Upper Cover” on page 58. 2. See “Removing the Bluetooth Module” on page 65. 3. See “Removing the I/O Board” on page 66. 4. See “Removing the LCD Module” on page 69. 5. Disconnect the speaker connector. 6. Remove the one (1) screw in the main board. Step Main Board Disassembly Chapter 3 Screw 2*3 Quantity Screw Type.
7. 72 Lift out the main board from the inside edge.
Removing the Thermal Module 1. See “Removing the Mainboard” on page 71. 2. Disconnect fan connector. 3. Remove the three (3) screws (red call outs) and loosen the two (2) captive screws (blue call outs). Step Thermal Module Disassembly Chapter 3 Screw 2*3 Quantity Screw Type.
4. 74 Lift the fan away from the main board.
Removing the CPU 1. See “Removing the Thermal Module” on page 73. 2. Using a flat head screwdriver to turn the CPU mounting lock to the OFF position. Locked CPU 3. Unlocked CPU Lift the CPU out and store carefully. WARNING:Do not touch the thermal grease to prevent bodily harm. Removing the RTC Battery. 1. See “Removing the Mainboard” on page 71.
2. 76 Lift the RTC battery out of its holder.
Removing the Speaker Modules 1. See “Removing the Mainboard” on page 71. 2. Remove the three (3) screws securing the Speakers to the lower cover. Step Speaker Module Disassembly 3. Screw 2*3 Quantity Screw Type. 3 Remove the tape from the speaker cable.
4. 78 Lift the speaker module out of the lower cover.
LCD Module Disassembly Process IMPORTANT: Cable paths and positioning may not represent the actual model. During the removal and replacement of components, ensure all available cable channels and clips are used and that the cables are replaced in the same position. NOTE: The product previews seen in the disassembly procedures may not represent the final product color or configuration.
Step LCD Bracket Disassembly 80 Screw 2*2.5 Quantity 4 Part No. 86.TPK07.
Removing the LCD Bezel 1. See “Removing the LCD Module” on page 69. 2. Remove the two (2) screw covers. 3. Remove the two (2) screws. Step Bezel Disassembly Chapter 3 Screw 2*5 Quantity Screw Type.
4. Pry the bezel free at the corner and lift the bezel off the hinge. 5. Pry the bezel free around the panel.
Removing the Camera Board 1. See “Removing the LCD Bezel” on page 81. 2. Disconnect the camera board connector 3. Lift the camera board out.
Removing the LCD Panel 1. See “Removing the Camera Board” on page 83. 2. Lift the microphone off the adhesive. 3. Remove the four (4) screws. Step LCD Panel Disassembly 84 Screw 2*3 Quantity Screw Type.
4. Lift the LCD panel out of the LCD module.
Removing the LCD Brackets 1. See “Removing the LCD Panel” on page 84. 2. Pick up the panel and remove the four (4) screws holding the brackets in place. Step LCD Panel Brackets Disassembly 86 Screw 2*2.5 (silver) Quantity Screw Type.
Removing the FPC Cable 1. See “Removing the LCD Panel” on page 84. 2. Pull the vertical foil strip off the microphone cable. 3. Pull off the horizontal foil strip till the FPC cable is completely exposed. 4. Pull the cable sleeve off the adhesive.
88 5. Lift up the clear connector protector. 6. Disconnect the connector. 7. Pull the microphone cable free of the adhesive.
Removing the Antennas 1. See “Removing the LCD Panel” on page 84. 2. Lift up the four (4) foil tabs on each corner. 3. Pull the wiring free of the retention guides.
90 4. Remove the magnet. 5.
LCD Reassembly Procedure Replacing the Antennas 1. Adhere the Right Antenna Pad (yellow and blue cable) to the LCD cover. 2. Adhere the Left Antenna Pad (white and blue cable) to the LCD Cover. 3. Insert the antenna cables into the retention guides around the top left corner of the LCD cover and then mount the magnet.
92 4. Insert the antenna cables into the retention guides around both sides. 5. Flatten the four (4) foil tabs on each corner.
Replacing the FPC Cable 1. Pull back the foil from the panel and lay the FPC cable on the panel 2. Apply adhesive and press down the FPC cable microphone extension. CAUTION: Ensure that the microphone is properly aligned with the top of the panel. 3. Connect the FPC cable connector.
94 4. Press down the clear FPC connector protective cover. 5. Apply adhesive and press down the FPC cable sleeve. 6. Press the foil back down on top of the FPC cable.
Replacing the LCD Brackets 1. Replace the four (4) screws in the left and right brackets. Step LCD Bracket Assembly Screw 2*2.5 (silver) Quantity Screw Type. 4 Replacing the LCD Panel 1. Place the LCD panel on the cover.
2. Replace the four (4) screws. Step LCD Panel Disassembly 3. 96 Screw 2*3 Quantity Screw Type. 4 Apply adhesive and press the microphone into place.
Replacing the Camera Board 1. Place the camera onto the LCD cover. 2. Connect the cable to the Camera Board Replacing the LCD Bezel 1. Place the bezel hinge cover over the hinges and ensure the wiring is correctly routed under the center hinge pin.
2. 98 Press the bezel down around the edges.
3. Replace the two (2) screws. Step LCD Bezel Assembly 4. Screw 2*5 Quantity Screw Type. 2 Replace the two screw covers.
Main Unit Reassembly Process Replacing the Speaker Module 1. Place the speaker module onto the lower cover. 2. Replace the three (3) screws Step Speaker Module Assembly 100 Screw 2*3 Quantity Screw Type.
3. Lay the cable into the retention guides and press down the adhesive tape. Replacing the RTC battery 1. Insert the RTC battery into the holding clips. Replacing the CPU 1. Place the CPU into the socket paying attention to the correct alignment of the locating triangle in the corner.
2. Turn the CPU lock to the locked position. Replacing the Thermal Module IMPORTANT: Ensure all heat pads are in place before replacing the Thermal Module. The following TIM material and dimensions (mm) are approved for use: CPU TIM PSX-D 18.3*12.3mm Vram TIM T-Flex-320 13*9*05mm 1. 102 PCHNB TIM FSL-BS 9.5*9.5*1mm Remove all traces of thermal grease or pad adhesive from the CPU and thermal module using a lint-free cloth or cotton swab and Isopropyl Alcohol, Acetone, or other approved cleaning agent.
2. Place the thermal module on the main board. 3. Tighten the two (2) captive screws (blue call outs) and replace the three (3) screws (red call outs) of the thermal module. Step Thermal Module Assembly 4. Screw 2*3 Quantity Screw Type. 3 Connect the fan cable to the main board.
Replacing the Mainboard 1. Place the main board into the lower cover on an angle first aligning the I/0 ports. 2. Replace the one (1) screw. Step Main Board Assembly 3. 104 Screw 2*3 Quantity Screw Type. 1 Connect the speaker connector.
Replacing the LCD Module 1. Thread the antenna cables through to the bottom side of the lower cover and place in the retention guides. 2. Place the hinges down on the lower case and ensure correct positioning of the antenna cables and the LCD cable and replace the two (2) screws. Step LCD Module Assembly Chapter 3 Screw 2*5 Quantity Screw Type.
3. Replace the LCD cable connector. 4. Press down the LCD cable connector protective cover. Replacing the I/O Board 1. 106 Place the I/O board into the lower cover on an angle first aligning the I/O ports.
IMPORTANT:Ensure that the WLAN/3G switch and the Bluetooth switch are properly aligned in the plastic slide switch covers in the lower cover. NOTE: You will feel the spring tension in the lower case sliders when the switches have been properly engaged. 2. Replace the one (1) screw. Step IO Board Assembly Chapter 3 Screw 2*5 Quantity Screw Type.
108 3. Reconnect the DC cable to the I/O board. 4. Lay the DC cable into the retention guide and press down the adhesive tape. 5. Reconnect the DC cable to the main board.
6. Reconnect the card reader cable. Replacing the Bluetooth Module 1. Place the Bluetooth module into position ensuring the board fits into the slot in the speaker module.
2. Reconnect the Bluetooth cable. Replacing the Button Board 1. 110 Place the button board on the upper cover.
2. Replace the two (2) screws. Step Button Board Assembly Screw 2-0.4*2 Quantity 3. Insert the button board cable into the upper cover. 4. Apply adhesive and press the button board cable down. Chapter 3 Screw Type.
112 5. Connect the button board cable to the button board. 6. Connect the touch pad cable to the touch pad and the button board.
Replacing the Upper Cover 1. Insert the IO cable into the upper cover. 2.
114 3. Press around the edges of the upper cover. 4. Connect the button board cable to the main board.
5. Connect the IO cable to the IO card and main board.
6. Replace the eleven (11) screws in the upper cover. Step Upper Cover Assembly 7. Screw 1 (green call out) 2*3 1 (blue call out) 2*5 9 (red call out) Screw Type. Replace the ten (10) screws in the lower cover. Step Lower Cover Assembly 116 Quantity 2.0*2.5 silver Screw Quantity 2*3 4 (red call out) 2*5 1 (green call out) 2*8 7 (red call out) Screw Type.
Replacing the Keyboard 1. Connect the keyboard cable into the mainboard. 2. Turn the keyboard over and press the keyboard into place Replacing the WLAN Module 1. Insert the WLAN module.
2. Replace the one (1) screw. Step WLAN Assembly 3. Screw 2*5 Quantity Screw Type. 1 Replace the two cables (white is MAIN, black AUX) Replacing the DIMM Module 1. 118 Insert the DIMM module.
2. Press the DIMM module down. Replacing the 3G Module 1. Insert the 3G module.
2. Replace the one (1) screw. Step 3G Board Assembly 120 Screw 2*4 Quantity Screw Type. 1 3. Lay the 3G antenna cables into the retention guides. 4. Connect the antenna cables (blue cable is MAIN, yellow cable is AUX).
Replacing the HDD Module 1. Attach the rails and replace the four (4) screws in the HDD rails. Step HDD Assembly 2. Screw 3.0*3.5 (silver) Quantity Screw Type. 4 Connect the HDD cable to the HDD.
3. Connect the HDD cable to the main board. 4. Lift up the black tab and place the HDD into the bay. Replacing the Lower Covers 1. 122 Replace the memory cover aligning the front tabs first.
2. Tighten the three (3) captive screws. 3. Replace the HDD cover, aligning the outside edge tabs first. 4. Tighten the two (2) captive screws.
Replacing the SIM Card 1. Insert the SIM card until it clicks into place. Replacing the Battery 124 1. Insert the battery. 2. Slide the battery lock switch into the closed position.
Replacing the Dummy Card 1. Insert the dummy card until it clicks into place.
126 Chapter 3
Chapter 4 Troubleshooting Common Problems Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
Power On Issue If the system doesn’t power on, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start Start OK Check AC/Battery Power on OK Check Daughter/B & FFC Whether OK NG Swap AC /Battery to try OK NG Swap Daughter/B Re-plug PWR FFC Swap M/B Computer Shuts down Intermittently If the system powers off at intervals, perform the following actions one at a time to correct the problem. 128 1.
No Display Issue If the Display doesn’t work, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: START Replace LCD Panel and Cable No LCD Module OK? Power On ? Ext. DDRAM module connected properly? Replace the main board No No Go to No Power troubleshooting step Reconnect SDRAM Module Ext.
5. Disconnect power and all external devices including port replicators or docking stations. Remove any memory cards and CD/DVD discs. Restart the computer. If the computer boots correctly, add the devices one by one until the failure point is discovered. 6. Reseat the memory modules. 7. Remove the drives (see “Disassembly Process” on page 34). 8. If the Issue is still not resolved, see “Online Support Information” on page 165.
4. If HDD information is missing from the BIOS, the drive may be defective and should be replaced. 5. Replace the Motherboard. 6. If the Issue is still not resolved, see “Online Support Information” on page 165. LCD Failure If the LCD fails, perform the following actions one at a time to correct the problem.
Built-In Keyboard Failure If the built-in Keyboard fails, perform the following actions one at a time to correct the problem.
Touchpad Failure If the Touchpad doesn’t work, perform the following actions one at a time to correct the problem.
Internal Speaker Failure If the internal Speakers fail, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start OK Check M/B SPK cable OK Check Logic Upper/Logic upper NG Re-assemble the SPK cable to M/B OK NG Swap Logic lower/Logic upper Swap M/B Sound Problems If sound problems are experienced, perform the following actions one at a time to correct the problem. 134 1. Reboot the computer. 2.
5. Ensure that all volume controls are set mid range: a. Click the volume icon on the taskbar and drag the slider to 50. Ensure that the volume is not muted. b. Click Mixer to verify that other audio applications are set to 50 and not muted. 6. Navigate to Start´ Control Panel´ Hardware and Sound´ Sound. Ensure that Speakers are selected as the default audio device (green check mark). NOTE: If Speakers does not show, right-click on the Playback tab and select Show Disabled Devices (clear by default).
1. Check that the microphone is enabled. Navigate to Start´ Control Panel´ Hardware and Sound´ Sound and select the Recording tab. 2. Right-click on the Recording tab and select Show Disabled Devices (clear by default). 3. The microphone appears on the Recording tab. 4. Right-click on the microphone and select Enable. 5. Select the microphone then click Properties. Select the Levels tab. 6. Increase the volume to the maximum setting and click OK. 7. Test the microphone hardware: 8. a.
USB Failure (Right up/down side) If the rightside USB port fails, perform the following actions one at a time to correct the problem. Do not replace non-defective FRUs: Start OK Check USB/B to M/B cable NG OK OK Check USB/B NG Re-assemble the USB/B cable to M/B Swap USB/B and USB cable Swap M/B Other Failures If the VGA board, LAN Port, external MIC or Speakers, PCI Express Card, 5-in-1 Card Reader or Volume Wheel fail, perform the following general steps to correct the problem.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
POST Code Reference Tables These tables describe the POST codes and components of the POST process.
Code Beeps 45h 46h POST device initialization 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h Initialize EISA board 52h Test keyboard 54h Set key click if enabled 58h 140 POST Routine Description 2-2-3-1 Test for unexpected interrupts 59h Initial
Code Beeps POST Routine Description 8Ah Initialize Extended BIOS Data Area 8Bh Test and initialize PS/2 mouse 8Ch Initialize floppy controller 8Fh Determine number of ATA drives (optional) 90h Initialize hard-disk controllers 91h Initialize local-bus hard-disk controllers 92h Jump to UserPatch2 93h Build MPTABLE for multi-processor boards 95h Install CD ROM for boot 96h Clear huge ES segment register 97h Fixup Multi Processor table 98h 1-2 Search for option ROMs.
Code Beeps C5h PnPnd dual CMOS (optional) C6h Initialize notebook docking (optional) C7h Initialize notebook docking late C8h Force check (optional) C9h Extended checksum (optional) D2h Unknown interrupt Code Beeps For Boot Block in Flash ROM E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize system timer E4h Initialize system I/O E5h Check force recovery boot E6h Checksum BIOS ROM E7h Go to BIOS E8h Set Huge Segment E9h Initialize
Chapter 5 Jumper and Connector Locations Mainboard Top View Item Chapter 5 Description Item Description CN1 LVD Connector CN8 ALC272 JSIMI SIM Card U6 Clock Generator PJ1 DC In CN3 Touch Pad Connector CN6 Lan Connector CN4 Keyboard Connector CN5 Bluetooth Connector U7 SB710 CN8 USB & Card Reader Connector U5 Keyboard controller CN7 Speaker Connector 143
Mainboard Bottom View Item 144 Description Item Description CN15 Fan Connector CN11 WIFI Card CN16 Lasso CN13 DRII Socket CN18 CRT CN14 DRII Socket PJ2 Battery Connector U19 CPU Socket CN12 3G Card CN17 USB CN10 RTC U18 RS780MN CN9 HDD Connector U17 Side Port Memory Chapter 5
BIOS Recovery BIOS Recovery by Crisis Disk BIOS Recovery Boot Block The BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to the factory settings if a BIOS flash process fails. BIOS Recovery Hotkey The system provides a function hotkey: Fn+Esc, to enable the BIOS Recovery process when a system is powered on during BIOS POST.
146 Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of the computer. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
California Exploded Diagrams Main Assembly 1 2 3 11 12 4 13 5 6 14 7 15 8 16 9 17 18 19 10 148 Item Acer PN Item Acer PN 1. Keyboard KB.I110A.085 11. Bluetooth Module BH.21100.004 2. Upper Cover 60.FRC07.001 12. DC Power Cable 50.FRC07.002 3. TP board 55.FRC07.002 13. I/O Board 55.FRC07.001 4. IO Cable TBC 14. 3G Module LC.21300.011 5. Mainboard MB.FRB06.001 15. Battery BT.00603.098 6. Thermal Cable TBC 16. WLAN Module NI.23600.047 7. Thermal Module 60.FRC07.
Item Acer PN Item Acer PN 9. Lower Cover 60.FRB07.001 19. HDD Door 42.FRC07.001 10. Memory Cover 42.FRC07.002 LCD Assembly 1 2 3 4 5 6 7 8 Item Acer PN Item Acer PN 1. LCD Bezel 60.FRC07.007 5. Antennas w/cable LZ.23500.006 2. LCD Panel LK.11605.003 6. Camera module 57.S6507.
Item 150 Acer PN Item Acer PN 3. LeftHinge 33.FRC07.002 7. Right hinge 33.FRC07.001 4.LCD FCP w/microphone 50.FRC07.004 8. LCD Module Case 60.FRB07.
California FRU ListV CATEGORY PARTNAME ACERPARTNO. ADAPTER ADAPTER DELTA 30W 19V 1.7X5.5X11 BLACK ADP-30JH BA LF AP.03001.001 ADAPTER LITE-ON 30W 1.7X5.5X11 BLACK PA-130004AC LF AP.03003.001 ADAPTER HIPRO 30W 19V 1.7X5.5X11 BLACK HPA0301R3 B1LF LF AP.0300A.001 Adapter DELTA 65W 19V 1.7x5.5x11 Yellow ADP-65JH DB A, LV5 LED LF AP.06501.026 Adapter LITE-ON 65W 19V 1.7x5.5x11 Yellow PA-165022AC LV5 LED LF AP.06503.024 Adapter HIPRO 65W 19V 1.7x5.5x11 Yellow HP-A0652R3B 1LF, LV5 LED LF AP.0650A.
CATEGORY PARTNAME ACERPARTNO. PWR CORD V943B30001218008 DANISH 3P 27.A03V7.006 PWR CORD(ISR)1.8M 3PBLK FZ0I0008-038 27.TATV7.005 PWR CORD V50CB3T3012180QD TW-110V,3P 27.A99V7.002 POWER CORD(SWI)1.8M 3PBLACK FZ010008-011 27.A99V7.004 POWER CORD(IT) 1.8M 3PBLACK FZ010008-008 27.A99V7.005 POWER CORD(S.A) 1.8M 3BLACK FZ010008-006 27.T48V7.001 POWER CORD US 3PIN ROHS 27.TAXV7.001 POWER CORD(EU) 1.8M 3PBLACK FM010008-010 27.TATV7.001 POWER CORD(UK) 1.8M 3PBLACK FP010008-013 27.TATV7.
CATEGORY PARTNAME ACERPARTNO. LCD COVER ASSY UV RED W/3G ANTENNA 60.FRB07.003 LCD COVER ASSY IMR RED W/3G ANTENNA 60.FRB07.004 LCD COVER ASSY UV RED W/WF ANTENNA 60.FRC07.005 LCD COVER ASSY IMR RED W/WF ANTENNA 60.FRC07.006 LCD BEZEL ASSY - BLACK 60.FRC07.007 HDD COVER - BLACK 42.FRC07.001 RAM COVER - BLACK 42.FRC07.002 HINGE - R 33.FRC07.001 HINGE - L 33.FRC07.002 SD DUMMY CARD 42.FRC07.003 Suyin Camera Rosa 2G, MODULE CN0316-S30C-OV06-1 57.S6507.001 CAMERA CNF9011(CMOS,0.
CATEGORY 154 PARTNAME ACERPARTNO. HDD TOSHIBA 2.5" 5400rpm 160GB MK1655GSX Libra SATA LF F/W: FG011J KH.16004.006 HDD HGST 2.5" 5400rpm 160GB HTS545016B9A300 Panther B SATA LF F/W:C60F Disk imbalance criteria = 0.014g-cm KH.16007.026 HDD WD 2.5" 5400rpm 160GB WD1600BEVT-22ZCTO ML160 SATA LF F/W:11.01A11 KH.16008.022 HDD SEAGATE 2.5" 5400rpm 250GB ST9250315AS Wyatt SATA LF F/W:0001SDM1 KH.25001.016 HDD TOSHIBA 2.5" 5400rpm 250GB MK2555GSX Libra SATA LF F/W:FG001J KH.25004.003 HDD HGST 2.
CATEGORY PARTNAME ACERPARTNO. KEYBOARD Chapter 6 Keyboard ACER NT1T Ferrari California 84KS Black Greek Texture KB.I110A.069 Keyboard ACER NT1T Ferrari California 84KS Black Thailand Texture KB.I110A.082 Keyboard ACER NT1T Ferrari California 85KS Black CZ/SK Texture KB.I110A.063 Keyboard ACER NT1T Ferrari California 85KS Black Hungarian Texture KB.I110A.070 Keyboard ACER NT1T Ferrari California 85KS Black Brazilian Portuguese Texture KB.I110A.
CATEGORY PARTNAME ACERPARTNO. Keyboard ACER NT1T Ferrari California 84KS Black US International w/ Hebrew Tex KB.I110A.086 Keyboard ACER NT1T Ferrari California 85KS Black Norwegian Texture KB.I110A.075 Keyboard ACER NT1T Ferrari California 84KS Black Korean Texture KB.I110A.073 Keyboard ACER NT1T Ferrari California 84KS Black Chinese Texture KB.I110A.064 LED LCD AUO 11.6" WXGA Glare B116XW02 V0 1A (3G) LF 200nit 8ms 500:1 LK.11605.003 LED LCD SAMSUNG 11.
CATEGORY PARTNAME ACERPARTNO. THERMAL MODULE 60.FRC07.008 SPEAKER MODULE ASSY(WITH L/R) 23.FRC07.001 LCD BEZEL RUBBER 47.FRC07.001 UPPER CASE RUBBER 47.FRC07.002 FRONT LENS RUBBER 47.FRC07.003 LOWER CASE RUBBER FOOT - BACK 47.FRC07.004 LOWER CASE RUBBER FOOT - FRONT 47.FRC07.005 SCREW M2*5-I(BZN)(NYLOK) 86.TG607.004 SPEAKER MISCELLANEOUS SCREW Chapter 6 SCREW M2.0*3.0-I,IRON SP 86.S0207.001 SCREW M2-0.4*2-I(BNI)(NYLOK)(7,0.6)IRON 86.W4107.002 SCREW M2.0*8.0-I(BZN)(NYLOK) 86.
158 Chapter 6
Appendix A Model Definition and Configuration Ferrari one Series Model RO FO200312G25n EMEA Greece LX.FRC02.138 FO200-312G25n W7HP64FRGR1 MC UMACrk 1*2G/250/6L2.8/5R/ CB_bgn_0.3D_AU_EL32 FO200313G25n EMEA Hungary LX.FRC02.078 FO200-313G25n W7HP64FRHU1 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_HU12 FO200312G25n CHINA Hong Kong LX.FRC02.151 FO200-312G25n W7HP64FRHK2 MC UMACrk 2*1G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_ZH35 FO200313G25n EMEA Portugal LX.FRC02.
160 Model RO Country Acer Part No Description FO200313G25n EMEA Denmark LX.FRC02.065 FO200-313G25n W7HP64FRDK2 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ENS1 FO200312G32n AAP Thailand LX.FRC02.150 FO200-312G32n EM W7HP64EMFRTH1 MC UMACrk 1*2G/320/BT/6L2.8/5R/ CB_bgn_0.3D_AU_TH42 FO200312G32n AAP Indonesia LX.FRC02.149 FO200-312G32n EM W7HP64EMFRID1 MC UMACrk 1*2G/ 320/BT/6L2.2/5R/ CB_bgn_0.3D_AU_ID22 FO200314G32n AAP Thailand LX.FRC02.
Model RO FO200312G25n EMEA Cyprus LX.FRC02.141 FO200-312G25n W7HP64FRCY1 MC UMACrk 1*2G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_ES62 FO200312G25n EMEA Israel LX.FRC02.140 FO200-312G25n W7HP64FRIL1 MC UMACrk 1*2G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_HE52 FO200312G25n EMEA Israel LX.FRC02.139 FO200-312G25n W7HP64FRIL1 MC UMACrk 1*2G/250/6L2.8/5R/ CB_bgn_0.3D_AU_HE32 FO200312G25n EMEA Cyprus LX.FRC02.136 FO200-312G25n W7HP64FRCY1 MC UMACrk 1*2G/250/6L2.8/5R/ CB_bgn_0.
162 Model RO Country Acer Part No Description FO200313G25n EMEA Middle East LX.FRC02.098 FO200-313G25n W7HP64EMFRME2 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_AR22 FO200312G25n CHINA China LX.FRC01.001 FO200-312G25n W7HB64SCFRCN1 MC UMACrk 1*2G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_SC12 FO200313G50n AAP Singapore LX.FRC02.122 FO200-313G50n W7HP64FRSG1 MC UMACrk 2G+1G/500_L/BT/6L2.8/5R/ CB_bgn_0.3D_AU_ES62 FO200314G50n AAP Singapore LX.FRC02.
Model RO FO200313G25n EMEA South Africa LX.FRC02.091 FO200-313G25n W7HP64EMFRZA2 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ES62 FO200313G25n EMEA Middle East LX.FRC02.095 FO200-313G25n W7HP64EMFRME6 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ES62 FO200313G25n EMEA Czech LX.FRC02.074 FO200-313G25n W7HP64FRCZ2 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_SK12 FO200313G25n EMEA Italy LX.FRC02.086 FO200-313G25n W7HP64FRIT1 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.
164 Model RO Country Acer Part No Description FO200313G25n EMEA UK LX.FRC02.089 FO200-313G25n W7HP64FRGB1 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ES62 FO200313G25n EMEA Algeria LX.FRC02.092 FO200-313G25n EM W7HP64EMFRDZ1 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ES82 FO200313G25n EMEA Middle East LX.FRC02.099 FO200-313G25n W7HP64EMFRME9 MC UMACrk 2G+1G/250/6L2.2/5R/ CB_bgn_0.3D_AU_ES82 FO200313G25n EMEA South Africa LX.FRC02.
Model RO FO200312G25n EMEA Spain LX.FRC02.013 FO200-312G25n W7HP64FRES1 MC UMACrk 2*1G/250/BT/6L2.8/5R/ CB_bgn_0.3D_AU_ES52 FO200312G25n EMEA France LX.FRC02.010 FO200-312G25n W7HP64FRFR1 MC UMACrk 1*2G/250/BT/6L2.2/5R/ CB_bgn_0.3D_AU_ES82 FO200314G25n WW WW S2.FRC02.005 FO200-314G25n W7HP64FWW1 MC UMACrk 2*2G/250/BT/6L2.2/5R/ CB_bgn_0.3D_AU_ES64 FO200312G25n EMEA UK LX.FRC02.007 FO200-312G25n W7HP64FRGB1 MC UMACrk 1*2G/250/BT/6L2.2/5R/ CB_bgn_0.3D_AU_ES62 FO200314G32n EMEA UK LX.
Model 166 RO Country Acer Part No Description FO200312G25n AAP Australia/ New Zealand LX.FRB02.003 FO200-312G25n W7HP64FRAU1 MC UMAGCrk 1*2G/250/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES62 FO200312G32n AAP Australia/ New Zealand LX.FRB02.004 FO200-312G32n W7HP64FRAU1 MC UMAGCrk 1*2G/320/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES62 FO200314G50n WW WW S2.FRB02.002 FO200-314G50n W7HP64FWW1 MC UMAGCrk 2*2G/500_L/BT/6L2.8/5R/ CB_bgn_0.3D_G2K_AU_ES64 FO200314G32n WW WW S2.FRB02.
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® XP Home, Windows® XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the Aspire one series Compatibility Test Report released by the Acer Mobile System Testing Department.
BRAND ACER Type Description NT1T Ferrari Keyboard ACER NT-1T Ferrari California Internal 11 Standard Black NONE Texture AR8131L Atheros AR8131L PIFA PIFA ALC272X Realtek Audio Codec ALC272X ABS UV Red ABS UV Red Mirror w/Camera Mirror w/Camera BT 2.1 Foxconn Bluetooth BRM 2046 BT2.1 (T60H928.33) f/w:861 0.
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
170
Index A E Antennas Euro Key 13 Removing 89, 91 External Module Disassembly Flowchart 40 B Battery Pack F Removing 42 Features 1 BIOS FLASH Utility 31 ROM type 18 vendor 18 Version 18 BIOS Utility 23–31 Advanced 26 Boot 29 Exit 30 Navigating 23 Save and Exit 30 Security 26 System Security 30 Bluetooth Module Removing 65, 109, 118, 119, 121, 122, 124 Flash Utility 31 FRU (Field Replaceable Unit) List 147 H Hard Disk Drive Module Removing 44 Hibernation mode hotkey 12 Hot Keys 10 I Indicator
Removing 69, 100, 105 Removing 102 LCD Module Disassembly Touch Pad Failure 133 Flowchart 79 Troubleshooting LCD Panel Built-in KB Failure 132 Internal Microphone 135 Internal Speakers 134 LCD Failure 131 No Display 129 ODD 137 Other Failures 137 Power On 128 Touch Pad 133 USB 137 Removing 84, 95 M Main Unit Disassembly Flowchart 54 Mainboard Removing 71, 104 media access on indicator 8 U Memory Check 128 Undetermined Problems 138 Microphone Upper Cover Removing 84, 95 Removing 58 Model
173
174
