Acer Aspire M5802(G) Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on this service guide.
Copyright Copyright © 2009 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated.
Disclaimer The information in this guide is subject to change without notice. Acer Incorporated makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties of merchantability or fitness for any particular purpose. Any Acer Incorporated software described in this manual is sold or licensed "as is".
Conventions The following conventions are used in this manual: SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives additional information related to the current topic. WARNING Alerts you to any physical risk or system damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Service Guide Coverage This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability). These LOCALIZED FEATURES will NOT be covered in this generic service guide.
Table of Contents System Tour Features Block Diagram System Components Front Panel Rear Panel Hardware Specifications and Configurations Power Management Function(ACPI support function) System Utilities CMOS Setup Utility Entering CMOS setup Navigating Through the Setup Utility Setup Utility Menus System Disassembly Disassembly Requirements Pre-disassembly Procedure Removing the Side Panel Removing the Front Bezel Removing the Heat Sink Fan Assembly Removing the Processor Removing the VGA Card Removing th
viii
Chapter 1 System Tour Features Below is a brief summary of the computer’s many feature: NOTE: The features listed in this section is for your reference only. The exact configuration of the system depends on the model purchased.
• • Capacity support: • 1GB / 2GB DDRII 667/800 Un-buffered Non-ECC DIMM support • 1GB to 8GB Max memory support Design Criteria: • • Should meet Intel G43 Express Chipset platform design guide Dual channel should be enabled always when plug-in 2 same memory size DDRII memory module Hard disk • Support up to two SATA ports • 3.5", 25.4mm • Capacity and models are listed on AVLC Optical disk • Support two SATA 5.
• 2 S/PDIF-out header (1*4) for ALC888S-VC sku • 1 front panel audio header (2*5) LAN • MAC Controller: ICH10R • PHY: Intel Boazman 82567V PCI-E Giga LAN USB ports • Controller: Intel ICH10R • Ports Quantity: 12 • • 4 back panel ports • On-board: 4 2*5 headers ( 8 ports) • 4 ports for front daughter board • Connector Pin: standard Intel FPIO pin definition Data transfer rate support: USB 2.0/1.
Block Diagram 4 Chapter 1
System Components This section is a virtual tour of the system’s interior and exterior components. Front Panel 12 11 1 10 2 3 9 4 8 7 5 6 Chapter 1 No. Component 1 USB 2.
Rear Panel 1 19 18 2 3 17 4 16 5 15 6 14 12 7 11 8 10 13 9 6 No. Component 1 Power connector 2 PS2 keyboard port 3 VGA port 4 HDMI port 5 USB 2.0 ports 6 Side Surround 7 Surround 8 Mic-in 9 Expansion slot (graphics card and TV tuner card and Mode card) 10 Line-out 11 Line-in 12 Center speaker/subwoofer jack 13 USB 2.
Hardware Specifications and Configurations Processor Item Specification Processor Type CPUs which complaint with Intel FSB 800/1066/1333 MHz CPUs Socket Type Intel Socket T LGA 755 pin FSB 1333 MHz Minimum operating speed 0 MHz (If Stop CPU Clock in Sleep State in BIOS Setup is set to Enabled.) BIOS Item Specification BIOS code programer AMI Kernel with Acer skin BIOS version P01-A0 BIOS ROM type SPI ROM BIOS ROM size 2Mb Support protocol SMBIOS(DMI)2.4/DMI2.
Memory Combinations Slot Memory Total Memory Slot 1 1MB,2GB 1G ~2GB Slot 2 1MB,2GB 1G ~2GB Slot 3 1MB,2GB 1G ~2GB Slot 4 1MB,2GB 1G ~2GB Maximum System Memory Supported 1G~8GB System Memory Item Specification Memory slot number 4 slot Support Memory size per socket 1GB/2GB Support memory type DDRII Support memory interface DDRII 667/800MHz Support memory voltage 1.
SATA Interface Item Specification SATA controller JMB362-QGEZ0A SATA controller resident bus PCI bus Number of SATA channel SATA X 6 Support bootable CD-ROM YES USB Port Item Specification Universal HCI USB 2.0/1.
Power Management Function(ACPI support function) Device Standby Mode • Independent power management timer for hard disk drive devices(0-15 minutes,time step=1minute). • Hard Disk drive goes into Standby mode(for ATA standard interface). • Disable V-sync to control the VESA DPMS monitor. • Resume method:device activated (keyboard for DOS, keyboard &mouse for Windows. • Resume recovery time 3-5sec Global Standby Mode • Global power management timer(2-120minutes,time step=10minute).
Chapter 2 System Utilities CMOS Setup Utility CMOS setup is a hardware configuration program built into the system ROM, called the complementary metaloxide semiconductor (CMOS) Setup Utility. Since most systems are already properly configured and optimized, there is no need to run this utility. You will need to run this utility under the following conditions.
Entering CMOS setup 1. Turn on the server and the monitor. If the server is already turned on, close all open applications, then restart the server. 2. During POST, press Delete. If you fail to press Delete before POST is completed, you will need to restart the server. The Setup Main menu will be displayed showing the Setup’s menu bar. Use the left and right arrow keys to move between selections on the menu bar.
Setup Utility Menus The Setup Main menu includes the following main setup categories.
Product Information The Product Information menu displays basic information about the system. These entries are for your reference only and are not user-configurable. Parameter Description Processor Type Type of CPU installed on the system. Processor Speed Speed of the CPU installed on the system. System Memory Total size of system memory installed on the system. Product Name Product name of the system. System Serial Number Serial number of the system.
Standard CMOS Features Parameter Description System Date Set the date following the weekday-month-day-year format. System Time Set the system time following the hour-minute-second format. Halt On Determines whether the system will stop for an error during the POST.
Advanced BIOS Feature Parameter Description Option Quick Boot Allows you to decrease the time it takes to boot the computer by shortening or skipping certain standard booting process. Enabled Quiet Boot When enabled, the BIOS splash screen displays during startup. Enabled When disabled, the diagnostic screen displays during startup. Disabled Specifies the boot order from the available devices.
Advanced Chipset Features Parameter Description Option Intel EIST When enabled, this feature allows the OS to reduce power consumption. Enabled When disabled, the system operates at maximum CPU speed. Disabled When enabled, the processor disables code execution when a worm attempts to insert a code in the buffer preventing damage and worm propagation. Enabled Intel XD Bit Disabled When disabled, the processor forces the Execute Disable (XD) Bit feature flag to always return to 0.
Integrated Peripherals Parameter Description Onboard SATA Controller Enables or disables the onboard SATA controller. Option Enabled Disabled Onboard SATA Mode Select an operating mode for the onboard SATA. RAID Native IDE Onboard USB Controller Enables or disables the onboard USB controller. Legacy USB Support Enables or disables support for legacy USB devices. Enabled Disabled Enabled Disabled USB Storage Emulation Enables or disables support for legacy USB devices.
Power Management Setup Parameter Description Option ACPI Suspend Mode Select an ACPI state. S3 (STR) Deep power off mode Select the Deep power off Mode S1 (POS) Enabled Disabled Power On by RTC Alarm Enables or Disables to wake up the system by RTC Alarm Function Enabled Power On by PCIE Devices Enables or disables to wake up the system from a power saving mode through an event on PCI Express device.
PC Health Status Parameter Description Option Smart FAN Enables or disables the smart system fan control function.
Frequency/Voltage Control Parameter Description Option Enable Clock to All DIMM/ PCI Enables or disables control the clock to all DIMM/PCI Enabled Spread Spectrum Chapter 2 Disabled Enables or disables the reduction of the mainboard’s EMI. Enabled Note: Remember to disable the Spread Spectrum feature if you are overclocking. A slight jitter can introduce a temporary boost in clock speed causing the overclocked processor to lock up.
BIOS Security Features Parameter Description Supervisor Password Indicates the status of the supervisor password. User Password Indicates the status of the user password. Change Supervisor Password Supervisor password prevents unauthorized access to the BIOS Setup Utility. Press Enter to change the Supervisor password. Setting a supervisor password 1. Use the up/down arrow keys to select Change Supervisor Password menu then press Enter. A password box will appear. 2.
Load Default Settings The Load Default Settings menu allows you to load the default settings for all BIOS setup parameters. Setup defaults are quite demanding in terms of resources consumption. If you are using low-speed memory chips or other kinds of low-performance components and you choose to load these settings, the system might not function properly.
Save & Exit Setup The Save & Exit Setup menu allows you to save changes made and close the Setup Utility. Exit Without Saving The Exit Without Saving menu allows you to discard changes made and close the Setup Utility.
Chapter 3 System Disassembly This chapter contains step-by-step procedures on how to disassemble the desktop computer for maintenance and troubleshooting. Disassembly Requirements To disassemble the computer, you need the following tools: • Wrist grounding strap and conductive mat for preventing electrostatic discharge • Flat-blade screwdriver • Philips screwdriver • Hex screwdriver • Plastic flat-blade screwdriver Plastic tweezers NOTE: The screws for the different components vary in size.
Pre-disassembly Procedure Before proceeding with the disassembly procedure, perform the steps listed below: 26 1. Turn off the system and all the peripherals connected to it. 2. Unplug the power cord from the power outlets. 3. Unplug the power cord from the system. 4. Unplug all peripheral cables from the system. 5. Place the system unit on a flat, stable surface.
Removing the Side Panel 1. Remove the two screws located on the rear edge of the side panel. 2. Slide the side panel toward the back of the chassis until the tabs on the cover disengage with the slots on the chassis. 3. Lift the side panel away from the server and put it aside for reinstallation later.
Removing the Heat Sink Fan Assembly WARNING:The heat sink becomes very hot when the system is on. NEVER touch the heat sink with any metal or with your hands. 28 1. disconnect the fan cable from the mainboard. 2. Use a long-nosed screwdriver to loosen the four screws on the heat sink, in the order as shown below. 3. Lift the heat sink fan assembly away from the mainboard.
Removing the Processor IMPORTANT:Before removing a processor from the mainboard, make sure to create a backup file of all important data. WARNING:The processor becomes very hot when the system is on. Allow it to cool off first before handling. 1. Release the load lever (1). 2. Pull the load lever to the fully open, upright position (2) and lift the load plate (3). 3. Pull out the processor from the socket.
Removing the VGA Card 30 1. Release the Slot cover lock. 2. Remove the screw from chassis. 3. Disconnect the power cables from the VGA card. 4. One finger Press the clip and the same time Gently pull the card to remove it from the mainboard.
Removing the TV Card 1. Gently pull the TV card to remove it from the mainboard. Removing the Mode Card 1. Gently pull the Mode card to remove it from the mainboard.
Removing the Hard Disk Drive 32 1. Disconnect the data and power cables from the rear of the optical drive and the mainboard. 2. Remove the HDD bracket a. Remove the screw that secures the HDD bracket to the ODD bracket. b. Lift the bracket up and turn it over.
3. Remove the HDD module a. Remove the eight screws secure the HDD module to the HDD bracket. b. Slide the HDD out of the bracket.
Removing the Front Bezel 34 1. Remove the side panel. Refer to the previous section for instructions. 2. Disconnect the LED cable. 3. Release the front bezel from the chassis interior. 4. Pull the bezel away from the chassis.
Removing the Optical Drive 1. Disconnect the data and power cables from the rear of the optical drive. Power cable 2. Remove Four screw from the optical drive. 3. Pull the drive out of the drive.
Removing Cables 1. Remove power switch and LED cables from slot of M/B 2. Remove HDD Data and ODD Data cables from slot of M/B. Powe-Led Cable ODD Cable HDD Cable Remove USB1/2/3 cable from M/B. 4. Remove SPDIF cable and Audio cable from M/B Front Audio Cable Front USB Cable (USB1) 3.
Remove System FAN 1. Remove System FAN cable from M/B. 2. Release four screws according to the following picture. 3. Take off the system fan from chassis.
Removing the Power Supply 38 1. Disconnect the 24-pin and 4-pin power supply cables from the mainboard. 2. Remove the four screw that secures the power supply to the chassis. 3. Lift the power supply module out of the chassis.
Removing the Memory Modules IMPORTANT:Before removing any DIMM from the memory board, make sure to create a backup file of all important data. 1. Press the holding clips on both sides of the DIMM slot outward to release the DIMM. 2. Gently pull the DIMM upward to pull it away from the M/B.
Removing the Mainboard 40 1. Remove the eight screws that secure the mainboard to the chassis. 2. Lift the board from the chassis.
Chapter 4 System Troubleshooting Please refer to generic troubleshooting guide for troubleshooting information relating to following topics: Chapter 4 • Power-On Self-Test (POST) • POST Check Points • POST Error Messages List • Error Symptoms List 41
Power-On Self-Test (POST) Each time you turn on the system, the Power-on Self Test (POST) is initiated. Several items are tested during POST, but is for the most part transparent to the user. The Power-On Self Test (POST) is a BIOS procedure that boots the system, initializes and diagnoses the system components, and controls the operation of the power-on password option.
Checkpoint Description DA Restore CPUID value back into register. Give control to BIOS POST (ExecutePOSTKernel). See POST Code Checkpoints section of document for more information. DC System is waking from ACPI S3 state E1-E8 EC-EE OEM memory detection/configuration error. This range is reserved for chipset vendors & system manufacturers. The error associated with this value may be different from one platform to the next.
Checkpoint Description 04 Check CMOS diagnostic byte to determine if battery power is OK and CMOS checksum is OK. Verify CMOS checksum manually by reading storage area. If the CMOS checksum is bad, update CMOS with power-on default values and clear passwords. Initialize status register A.Initializes data variables that are based on CMOS setup questions. Initializes both the 8259 compatible PICs in the system 05 Initializes the interrupt controlling hardware (generally PIC) and interrupt vector table.
Checkpoint Description 38 Initializes different devices through DIM. See DIM Code Checkpoints section of document for more information. USB controllers are initialized at this point. 39 Initializes DMAC-1 & DMAC-2. 3A Initialize RTC date/time. 3B Test for total memory installed in the system. Also, Check for DEL or ESC keys to limit memory test. Display total memory in the system. 3C Mid POST initialization of chipset registers.
Checkpoint Description AC End of POST initialization of chipset registers. B1 Save system context for ACPI. 00 Passes control to OS Loader (typically INT19h). 61-70 OEM POST Error. This range is reserved for chipset vendors & system manufacturers. The error associated with this value may be different from one platform to the next.
POST Error Messages List If you cannot run the diagnostics program tests but did receive a POST error message, use "POST Error Messages List" to diagnose system problems. If you did not receive any error message, look for a description of your error symptoms in "Error Symptoms List" NOTE: When you have deemed it necessary to replace an FRU, and have done so, you must run a total system check to ensure that no other activity has been affected by the change.
Message Displayed Description B: Drive Error The BIOS attempted to configure the B: drive during POST, but was unable to properly configure the device. This may be due to a bad cable or faulty diskette drive. Insert BOOT diskette in A: The BIOS attempted to boot from the A: drive, but could not find a proper boot diskette.
Message Displayed Description 5th Slave Hard Disk Error The IDE/ATAPI device configured as Slave in the 5th IDE controller could not be properly initialized by the BIOS. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. 6th Master Hard Disk Error The IDE/ATAPI device configured as Master in the 6th IDE controller could not be properly initialized by the BIOS.
Message Displayed Description 6th Slave Drive - ATAPI Incompatible The IDE/ATAPI device configured as Slave in the 6th IDE controller failed an ATAPI compatibility test. This message is typically displayed when the BIOS is trying to detect and configure IDE/ATAPI devices in POST. S.M.A.R.T. Capable but Command Failed The BIOS tried to send a S.M.A.R.T. message to a hard disk, but the command transaction failed. This message can be reported by an ATAPI device using the S.M.A.R.T.
Message Displayed Description Microcode Error BIOS could not find or load the CPU Microcode Update to the CPU. This message only applies to INTEL CPUs. The message is most likely to appear when a brand new CPU is installed in a motherboard with an outdated BIOS. In this case, the BIOS must be updated to include the Microcode Update for the new CPU. NVRAM Checksum Bad, NVRAM Cleared There was an error in while validating the NVRAM data. This causes POST to clear the NVRAM data.
Message Displayed Description CMOS Settings Wrong CMOS settings are invalid. This error can be resolved by using AMIBIOS Setup. CMOS Checksum Bad CMOS contents failed the Checksum check. Indicates that the CMOS data has been changed by a program other than the BIOS or that the CMOS is not retaining its data due to malfunction. This error can typically be resolved by using AMIBIOS Setup. Miscellaneous Message Displayed Description KBC BAT Test failed Keyboard controller BAT test failed.
USB eModule Error Messages Message Displayed Description Warning! Unsupported USB device found and disabled! This message is displayed when a non-bootable USB device is enumerated and disabled by the BIOS. Warning! Port 60h/64h emulation is not supported by this USB Host Controller! This message is displayed to indicate that port 60h/64h emulation mode cannot be enabled for this USB host controller. This condition occurs if USB KBC emulation option is set for non-SMI mode.
Error Symptoms List NOTE: To diagnose a problem, first find the error symptom in the left column. If directed to a check procedure, replace the FRU indicated in the check procedure. If no check procedure is indicated, the first Action/ FRU listed in right column is the most likely cause.
Error Symptom Action/FRU Diskette drive does not work. 1.Ensure the diskette drive is not set to None in the Disk Drives of BIOS Setup. 2.Diskette drive power 3.Diskette drive connection/cable 4.Diskette drive 5.Main board Diskette drive read/write error. 1.Diskette. 2.Diskette drive cable. 3.Diskette drive. 4.Main board Diskette drive LED comes on for more than 2 minutes when reading data. 1.Diskette 2.Diskette drive connection/cable 3.Diskette drive 4.
Error Symptom Action/FRU CD/DVD-ROM drive LED doesn't come on but works normally. 1.CD/DVD-ROM drive CD/DVD-ROM drive LED flashes for more than 30 seconds before LED shutting off. Software asks to reinstall disc.Software displays a reading CD/DVD error. 1.CD/DVD-ROM may have dirt or foreign material on it. Check with a known good disc. 2. CD/DVD-ROM is not inserted properly. 3.CD/DVD-ROM is damaged.
Error Symptom Action/FRU Video memory test failed.Video adapter failed. 1.Remove all non-factory-installed cards. 2.Load default settings (if screen is readable). 3.Main board Display problem: -Incorrect colors No high intensity Missing, broken, or incorrect characters Blank monitor (dark) Blank monitor (bright) Distorted image Unreadable monitor 1.Monitor signal connection/cable. 2.Monitor 3.Video adapter card 4.Main board Other monitor problems Display changing colors. 1.
Error Symptom Action/FRU Executing software shutdown from Windows98 Start menu does not turn off the system. (Only pressing power switch can turn off the system). 1.Load default settings. 2.Reload software from Recovery CD. No system power, or power supply fan is not running. 1.Power Supply 2.Main board Other Problems Any other problems. 58 1.
Undetermined Problems If an error message is present, go to "POST Error Messages List" on page 85. If you did not receive any messages, if the symptom is listed in "or "Error Symptoms List" on page 87. If you still cannot solve the problem, continue with this check: 1. Check the power supply voltage. If the voltage are correct continue with the following steps: 2. Power off the system unit. 3. Perform the following checks, one by one, until you have isolated the problem FRU. 4.
Chapter 5 Jumper and Connector Information M/B Placement Chapter 5 60
No Label Description No Label Description 1 CPU Socket CONN,Socket,IntelPrescot tCPU,LGA775P,10u,G,SMD 11 1394A1 Onboard 1394a header 2 CPU_FAN CPU fan power header 12 SPDIF_OUT1 ~2 SPDIF out header 3 DIMM1~4 CONN,DIMM,DDRIII,1.
Jumper Setting The section explains how to set jumper for correct configuration of the mainboard. Setting Jumper Use the motherboard jumpers to set system configuration options. Jumpers with more Than one pin are numbered. When setting the jumpers, ensure that the jumper caps are Placed on the correct pins.
Jumper/Header Name Function SYS FAN HEADER (3pin & 4 pin colay default:3 pin) 1: GND 2: +12V 3: SENSE 4: PWM CONTROL(4 pin Fan) FRONT PANEL HEADER 1: SATALED+ 2: ACPI_LED 3: SATALED4: PWR_LED 5: GND 6: PWR_SW 7: RESET 8: GND 9: NC 10: Key 11: NC 12: VCC 13: NC 14: -ACTIVE_C FRONT USB HEADER 1: USBVCC_1 2: USBVCC_1 3: USB0_XN 4: USB1_XN 5: USB0_XP 6: USB1_XP 7:GND 8: GND 9: KEY 10: GND F_USB1 1 3 5 7 9 VCC VCC USB0- USB1- USB0+ USB1+ GND GND KEY OC0 2 4 6 8 10 H5X2-P9E-Y F_USB2 1 3 5 7 9
Jumper/Header Name Function F_USB3 1 3 5 7 9 VCC VCC USB0- USB1- USB0+ USB1+ GND GND KEY OC0 2 4 6 FRONT USB HEADER 8 10 H5X2-P9E-Y -O Chapter 5 Definition 1: USBVCC_3 2: USBVCC_3 3: USB5_XN 4: USB7_XN 5: USB5_XP 6: USB7_XP 7:GND 8: GND 9: KEY 10: GND FRONT USB HEADER 1: USBVCC_4 2: USBVCC_4 3: USB3_XN 4: USB6_XN 5: USB3_XP 6: USB6_XP 7:GND 8: GND 9: KEY 10: GND FRONT AUDIO HEADER 1: PORT-F_L 2: AUGND 3: PORT-F_R 4: FRONT_AUD_DET 5: PORT-E_R 6: MIC2_JD 7: AUGND 8: KEY 9: PORT-E_L 10: L
Jumper/Header Name Function FRONT 1394 HEADER Definition 1: T_PA0+ 2: T_PA03: GND 4: GND 5: T_PB0+ 6: T_PB07: CPWR1 8: CPWR1 9: KEY 10: GND Connector pin definition Connector Name 65 Function Definition PSKBMS CONN 1: KBDATA 2: NC 3: GND 4: KBVCCSB 5: KBCLK 6: NC 7: MSDATA 8: NC 9: GND 10: KBVCCSB 11: MSCLK 12: NC 13: GND 14: GND 15: GND 16: GND 17: GND HDMI CONN 1: HDMI_TX2_P 3: HDMI_TX2_N 4: HDMI_TX1_P 6: HDMI_TX1_N 7: HDMI_TX0_P 9: HDMI_TX0_N 10: HDMI_TXC_P 12: HDMI_TXC_N 13,14: NC 15: SLHD_CLK
Connector Name Chapter 5 Function Definition VGA CONN 1: RED 2: GREEN 3: BLUE 4,11: NC 9: HDMIVCC 12: VDAC_SDAT 13: HSYNC 14: VSYNC 15: VDAC_SCLK 5,6,7,8,10,16,17: GND USB+1394 CONN 1: USBVCC_5 2: USB9_XN 3: USB9_XP 4: AUGND2 5: USBVCC_5 6: USB8_XN 7: USB8_XP 8: AUGND2 9: CPWR2 10: AUGND2 11: T_PB112: T_PB1+ 13: T_PA114: T_PA1+ 15: USBVDD1 G1,G2,G3,G4,G5,G6,G7, G8: AUGND2 66
Connector Name 67 Function Definition USB+LAN CONN 1:USBVCC_6 12:MDI1_P 2:USB10_XN 13:MDI1_N 3:USB10_XP 14:MDI2_P 4:AUGND2 15:MDI2_N 5:USBVCC_6 16:MDI3_P 6:USB11_XN 17:MDI3_N 7:USB11_XP 18:DGND 8:AUGND2 9:LAN_1P8V 10: MDI0_P 11: MDI0_N 19:LAN_LED2 20:LAN_LED1 21: LAN_LED0 22: CL_3P3V G1,G2,G3,G4,G5,G6,G7, G8: AUGND2 SATA CONN 1: GND 2: SATA0_TX_P 3: SATA0_TX_N 4: GND 5: SATA0_RX_N 6: SATA0_RX_P 7: GND SATA CONN 1: GND 2: SATA1_TX_P 3: SATA1_TX_N 4: GND 5: SATA1_RX_N 6: SATA1_RX_P 7: GND Chapter 5
Connector Name Chapter 5 Function Definition SATA CONN 1: GND 2: SATA2_TX_P 3: SATA2_TX_N 4: GND 5: SATA2_RX_N 6: SATA2_RX_P 7: GND SATA CONN 1: GND 2: SATA3_TX_P 3: SATA3_TX_N 4: GND 5: SATA3_RX_N 6: SATA3_RX_P 7: GND SATA CONN 1: GND 2: SATA4_TX_P 3: SATA4_TX_N 4: GND 5: SATA4_RX_N 6: SATA4_RX_P 7: GND SATA CONN 1: GND 2: SATA5_TX_P 3: SATA5_TX_N 4: GND 5: SATA5_RX_N 6: SATA5_RX_P 7: GND 68
Connector Name 69 Function Definition ATX_POWER CONN 1:VCC3 13:VCC3 2:VCC3 14:-12V 3: GND 15:GND 4:VCC 16:ATX_PSON_L 5:GND 17:GND 6:VCC 18:GND 7:GND 19:GND 8:ATX_PWRGD 20:NC 9:5VSB 21VCC 10:+12V 22:VCC 11:+12V 23:VCC 12:VCC3 24:GND ATX12V CONN 1: GND 2: GND 3: +12V_4P 4: +12V_4P Chapter 5
Chapter 6 FRU (Field Replaceable Unit) List This chapter offers the FRU (Field Replaceable Unit) list in global configuration of the Aspire M5802 desktop computer. Refer to this chapter whenever ordering the parts to repair or for RMA (Return Merchandise Authorization). NOTES: chapter 6 • When ordering FRU parts, check the most up-to-date information available on your regional web or channel. For whatever reasons a part number is changed, it will NOT be noted on the printed Service Guide.
Aspire M5802 Exploded Diagram NOTE: This section will be updated when more information becomes available.
ITEM NAME TYPE Q’TY ITEM NAME TYPE Q’TY 1 PANEL_TOP-X2 PART 1 21 DOOR_ODD_ARM_LOX1 PART 1 2 COVER_TOP-X1 PART 1 22 DOOR_ODD_UP_M5-X2 PART 1 3 MYLAR-COVER-TOP 23 BTN_ODD_LO-X1 PART 2 4 MYLAR-DOOR-TOP 24 BTN_ODD_DCR_UP-X1 PART 2 5 DOOR_TOP-X1 PART 1 25 SPRING_ODD_BTN-2 PART 4 6 LED_3 PART 1 26 LOGO_ASPIRE_M5-X1 PART 1 7 BTN_PWR_DCR-X1 ELECT RONIC 1 27 LOGO-AM530 PART 1 8 BTN_PWR_V2-X1 PART 1 28 PANEL_FRT_LO-X2 PART 1 9 MCR_HOLDER-X4 PART 1
Aspire M5802 FRU List Category Description Part Number MAINBOARD MB Kit HimalayanII_D2 Intel G43 ICH10R GMA X4500 384M Intel 82567V Giga LAN ATX W/ 1394 V1.0 LF w/ EuP Lot6 MB.SCQ07.002 NS 16-in-1 CR M5 w/USB2.0, Realtek RTS-5181,w/micro SD, M2 CR.10400.075 KYE 16-in-1 CR M5 w/USB2.0, Realtek RTS-5181,w/micro SD, M2 CR.10400.073 FAN COOLER P4_SKT775 PKP367 W/I SUNON 4000RPM HI.3670C.001 Fan Cooler LGA775 TMD06 Fan 9225 HI.10800.006 FR 500W EUP 82+ (ES5.0) PY.50008.004 Core 2 Quad Q9650 (3.
Category Description Part Number Core 2 Duo E7300 (2.66G 3M 1066FSB) , 65W , M0 KC.73001.DE0 Pentium Dual Core E6300 (2.8G 2M 1066FSB) , 65W , R-0 KC.63001.DEM Pentium Dual Core E5400 (2.7G 2M 800FSB) , 65W , R-0 KC.54001.DEV Pentium Dual Core E5300 (2.6G 2M 800FSB) , 65W , R-0 KC.53001.DEV Pentium Dual Core E5200 (2.5G 2M 800FSB) , 65W , R-0 KC.52001.DER Memory UNIFOSA UNB-DIMM DDRII 800 1GB GU341G0ALEPR6B2C6F1 LF 128*8 0.065um KN.1GB0H.
Category Description Part Number ODD DH-16D5S Win7 KV.0160F.002 DH-20N(H/F) Win7 KV.0160D.016 GH-41F(H/F) Win7 non-Labelflash KU.0160D.049 DH-16AASH (H/F) Win7 non-Labelflash KU.0160F.009 DH-4O3S Win7 KV.0040F.002 CH-10F Win7 non-Labelflash KO.0060D.004 DH-6E2S Win7 non-Labelflash KO.0060F.002 BH-30F (H/F) Win7 non-Labelflash KU.0060D.004 GEFORCE GTS250 1GB GDDR3 QIMUNDA (256BITS) DUAL DVI ATX BRACKET VG.PCGT2.501 GEFORCE GTS240 2GB GDDR3 SAMSUNG (256BITS) VGA DVI HDMI ATX BRACKET VG.
Category Description Part Number SPEAKER Neosonica Speaker USB with new color AC-MT-018 SP.10600.027 Lite-on Optical mouse USB SM-9625 with new color AC-MT-018 MS.11200.048 Chicony RF2.4 MG-0766 with new silver color MS.11200.054 Keyboard LITE-ON SK-9625 USB Standard 104KS Black US with new color AC-MT-018 KB.USB0B.082 Keyboard LITE-ON SK-9625 USB Standard 104KS Black Simplified Chinese with new color AC-MT-018 KB.USB0B.
Category 77 Description Part Number Keyboard LITE-ON SK-9625 USB Standard 105KS Black Belgium with new color AC-MT-018 KB.USB0B.100 Keyboard LITE-ON SK-9625 USB Standard 105KS Black Icelandic with new color AC-MT-018 KB.USB0B.101 Keyboard LITE-ON SK-9625 USB Standard 105KS Black Norwegian with new color AC-MT-018 KB.USB0B.102 Keyboard LITE-ON SK-9625 USB Standard 104KS Black Hebrew with new color AC-MT-018 KB.USB0B.
Category Chapter 6 Description Part Number Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black US International with new silver color KB.RF403.138 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Arabic/English with new silver color KB.RF403.139 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Thailand with new silver color KB.RF403.140 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Spanish with new silver color KB.RF403.141 Keyboard CHICONY KG-0766 RF2.
Category 79 Description Part Number Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Hungarian with new silver color KB.RF403.161 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Greek with new silver color KB.RF403.162 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Danish with new silver color KB.RF403.163 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Czech with new silver color KB.RF403.164 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Romanian with new silver color KB.
Category Chapter 6 Description Part Number Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black German with new silver color KB.RF403.146 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Italian with new silver color KB.RF403.147 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black French with new silver color KB.RF403.148 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Swedish with new silver color KB.RF403.149 Keyboard CHICONY KG-0766 RF2.
Category 81 Description Part Number Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Arabic/French with new silver color KB.RF403.169 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Kazakh with new silver color KB.RF403.170 Keyboard CHICONY KG-0766 RF2.4 Standard 104KS Black Turkmen with new silver color KB.RF403.171 Keyboard CHICONY KG-0766 RF2.4 Standard 105KS Black Nordic with new silver color KB.RF403.
Chapter 7 Intel RAID SOP INTEL® MATRIX STORAGE TECHNOLOGY CHECK(DOS) 1.Intel(R) Matrix Storage Manager option ROM 1-1: Create SATA RAID 0 Step 1:Shut down the EUT, unplug the power cable,connect two SATA HDDS to EUT , check the EUT all devices are connect/plug ok. Step 2:Press "PWR-BTTN" to power on the EUT,Load BIOS default setting . Step 3:At "Integrated_Peripherals" page "OnChip SATA Type" item set is as "RAID" mode,save and exit.
Step 6:Create RAID 0 Mode,enter the RAID name,such as "MyRaid0",default is"Volume0". Picture2 Step 7:Select "RAID0(Stripe)" at "RAID Level".
Step 8:You can select the "Strip Size" and define RAID capacity in "Capactity". Picture4 Step 9:Press "Create Volume" to create RAID0,it will pop the warning message that all data will be lost,"press "Y" to confirm it. Picture5 Step 10:It will back to create RAID interface,then press "ESC" or select 4 to exit and install OS.
1-2: Create SATA RAID 1 Step 1:Shut down the EUT, unplug the power cable,connect two SATA HDDS to EUT , check the EUT all devices are connect/plug ok. Step 2:Press "PWR-BTTN" to power on the EUT,Load BIOS default setting . Step 4:During BIOS post, press to enter into Intel RAID setup utility. Step 5: Select "1" to enter create RAID mode ,if there is no enough avalable space (there was exist a Raid , delete it ). Step 6:Create RAID 1 Mode,enter the RAID name,such as "MyRaid1",default is"Volume0".
Step 7:Select "RAID5(Parity)" at "RAID Level". Picture7 Step 8:You can select the "Strip Size" and define RAID capacity in "Capactity". Step 9:Press "Create Volume" to create RAID5,it will pop the warning message that all data will be lost,"press "Y" to confirm it. Step 10:It will back to create RAID interface,then press "ESC" or select 4 to exit and install OS.
Step 8:Select two HDDs in "Disk" by space key. Picture8 Step 9:Press "Enter" to finish HDD selection and it will back to RAID creation interface. Step 10:Repeat RAID1 creation step and exit,then install OS.
Intel RAID SOP (Windows for WIN7) 2.Intel(R) Matrix Storage Console 2-1:Create a“RAID Ready” System into" RAID 0" with two Hard Drives by‘Create RAID Volume from Existing HDD Drive ’. Step 1:Install Win7 OS with one SATA HDD. Step 2:Shut down the system,then add one Serial ATA hard drive in the system. Step 3:Boot to OS desktop, open the Intel® Matrix Storage Console. Picture1 Step 4:Click on the by‘Create RAID Volume from Existing HDD Drive ’ to create a RAID volume.
Step 5:Click "Next" at create a RAID volume window. Picture3 Step 6:Key the name in "Volume Name" and select "RAID 0" in RAID Level. Picture4 Step 7:Select minimum HDD as "Source Hard Drive".
Picture6 Step 8:Select Menber Hard Drive(s).
Step 9:Specify Volume Size then press "next". Picture8 Step 10:Press "next" to finish setup and start create RAID0. Picture9 Step 11:It may takes half and hours to create RAID0.After create completely,it will ask to reboot to finish create RAID0. 2-2:Create a“RAID Ready” System into" RAID 1" with two Hard Drives by‘Create RAID Volume from Existing HDD Drive ’. Step 1:Install WIN7 OS with one SATA HDD. Step 2:Shut down the system,then add another Serial ATA hard drive in the system.
Step 6:Key the name in "Volume Name" and select "RAID 1" in RAID Level. Picture10 Step 7:Select minimum HDD as "Source Hard Drive". Step 8:Select Menber Hard Drive(s). Step 9:Specify Volume Size then press "next". Step 10:Press "next" to finish setup and start create RAID1. Step 11:It may takes half and hours to create RAID1.After create completely,it will ask to reboot to finish create RAID1.
Step 6:Key the name in "Volume Name" and select "RAID 5" in RAID Level. Picture11 Step 7:Select minimum HDD as "Source Hard Drive".
Step 8:At least select two HDD as Menber Hard Drive(s). Picture13 Step 9:Specify Volume Size then press "next". Step 10:Press "next" to finish setup and start create RAID5. Step 11:It may takes half and hours to create RAID5.After create completely,it will ask to reboot to finish create RAID5. 2-4:Create a“RAID Ready” System into" RAID 10" with three Hard Drives by‘Create RAID Volume from Existing HDD Drive ’. Step 1:Install Win7 OS with one SATA HDD.
Step 7:Select two HDDs as "Source Hard Drive". Picture15 Step 8:At least select two HDD as Menber Hard Drive(s). Step 9:Specify Volume Size then press "next". Step 10:Press "next" to finish setup and start create RAID 10. Step 11:It may takes half and hours to create RAID 10.After create completely,it will ask to reboot to finish create RAID10. 2-5:Create a“RAID Ready” System into" RAID 0" with two Hard Drives by ‘Create RAID Volume ’. Step 1:Install WIN7 OS with one SATA HDD.
Step 5:Click "Next" at create a RAID volume window. Step 6:Key the name in "Volume Name" and select "RAID 0" in RAID Level. Step 7:At least select two HDDs as "Volume Location". Picture17 Step 8:Specify Volume Size then press "next". Picture18 Step 9:Press "next" to finish setup and start create RAID 0. Step 10:It may takes half and hours to create RAID 0.After create completely,it will ask to reboot to finish create RAID 0.
2-6:Create a“RAID Ready” System into" RAID 1" with two Hard Drives by ‘Create RAID Volume ’. Step 1:Install WIN7 OS with one SATA HDD. Step 2:Shut down the system,then add another two serial ATA hard drives in the system. Step 3:Boot to OS desktop, open the Intel® Matrix Storage Console. Step 4:Click on the by‘Create RAID Volume’ to create a RAID volume. Step 5:Click "Next" at create a RAID volume window. Step 6:Key the name in "Volume Name" and select "RAID 1" in RAID Level.