BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!jj!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN Copyright © 2003 Acer Incorporated All Rights Reserved. Acer Altos G900 User’s guide January 2003 Changes may be made periodically to the information in this publication without obligation to notify any person of such revision or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications.
BB!H:11!vh!.!FO/cppl!!Qbhf!jjj!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN iii Notices FCC notice This device has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
BB!H:11!vh!.!FO/cppl!!Qbhf!jw!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN iv Use conditions This part complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Notice: Canadian users This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
BB!H:11!vh!.!FO/cppl!!Qbhf!w!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN v Important safety information Only a technically qualified person shall access, integrate, configure, and service this product. Intended application uses This product was evaluated as an Information Technology Equipment (ITE), which may be installed in offices, schools, computer rooms, and similar commercial type locations.
BB!H:11!vh!.!FO/cppl!!Qbhf!wj!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN vi Multiple power cords Warning! To avoid electrical shock, disconnect all AC power cords before accessing inside the system. Earth grounded socket-outlets Warning! To avoid electrical shock, the system power cord(s) must be plugged into socket-outlet(s) that is provided with a suitable earth ground.
BB!H:11!vh!.!FO/cppl!!Qbhf!wjj!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN vii Equipment rack precautions Follow the rack manufacturer's safety and installation instructions for proper rack installation. The following additional rack safety installation measures shall be considered: • Anchor the equipment rack The equipment rack must be anchored to an unmovable suitable support to prevent the rack from falling over when one or more systems are fully extended out of the rack assembly.
BB!H:11!vh!.!FO/cppl!!Qbhf!wjjj!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN viii Important safety instructions Read these instructions carefully. Save these instructions for future reference. 1 Follow all warnings and instructions marked on the product. 2 Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 3 Do not use this product near water. 4 Do not place this product on an unstable cart, stand, or table.
BB!H:11!vh!.!FO/cppl!!Qbhf!jy!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN ix d If the product does not operate normally when the operating instructions are followed. Adjust only those controls that are covered by the operating instructions since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
BB!H:11!vh!.
Notices FCC notice Laser compliance statement Important safety information Intended application uses Checking the power cords Precautionary reminders Equipment rack precautions Important safety instructions 1 System tour Features overview Altos G900 physical specifications External and internal structure Access covers Main chassis components Electronics bay components Front control panel Rear panel Peripheral device bay Server board set features Mainboard layout System cables System features Processors Mem
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!3!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This chapter gives you a tour of the system’s internal and external components, as well as a discussion of its many features.
BB!H:11!vh!.!FO/cppl!!Qbhf!4!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 3 Features overview The Acer Altos G900 four-way performance server model utilizes a PCI bus based mainboard built on an ATX form factor. It supports up to four processors from the Intel® Xeon™ processor family. For expandability, the mainboard supports eight full length PCI slots (4 PCI-X hot plug, 2 PCI-X non-hot plug, 2 PCI non-hot plug).
BB!H:11!vh!.!FO/cppl!!Qbhf!5!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 4 1 System tour Altos G900 physical specifications Specification Rack-mount orientation Tower orientation Height 12.25 inches (311 mm) (7U) 18.09 inches (459 mm) Width Fits 19-inch rack 12.24 inches (311 mm) Depth 25.25 inches (641 mm) 25.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!7!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 6 1 System tour Main chassis components The figure below shows the chassis with the access panels removed. Figure 2 - Main chassis components Label Description Label Description A Hot-plug PCI add-in cards F CD-ROM drive B Memory board G 5.25-inch peripheral bay C Electronics bay H 3.
BB!H:11!vh!.!FO/cppl!!Qbhf!8!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 7 Electronics bay components The figure below shows the electronics bay with the access cover and memory board removed.
BB!H:11!vh!.!FO/cppl!!Qbhf!9!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 8 1 System tour Front control panel The figure below describes the features of the front control panel. Figure 4 - Front control panel Label Description Operation A Power button To turn power on, press the power button momentarily. If the system is in sleep state, pressing the power button momentarily brings the system out of the sleep state. To turn power off, press and hold the power button for more than four seconds.
BB!H:11!vh!.!FO/cppl!!Qbhf!:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 9 Label Description Operation E NMI switch Causes a non-maskable interrupt. Located behind the bezel door. F USB connector USB port 3. Located behind the bezel door. G Serial port connector Serial port B. Located behind the bezel door. H Lock Locks the bezel and front access cover. I Chassis ID LED Blue indicates chassis ID is active. J LAN2 LED Green indicates LAN2 activity. K LAN1 LED Green indicates LAN1 activity.
BB!H:11!vh!.!FO/cppl!!Qbhf!21!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 10 1 System tour Rear panel The figure below describes the features of the rear panel.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!23!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 12 1 System tour Peripheral device bay Opening the right bezel door provides access to the peripheral bay. The peripheral bay consists of four bays for removable media: Figure 6 - Peripheral device bay Label Description Label Description A Front bezel door B LED status indicators Caution! It is not recommended to install a hard disk drive in the 5.
BB!H:11!vh!.!FO/cppl!!Qbhf!24!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 13 Server board set features The server board set for Altos G900 consists of a mainboard, memory board, and processor board. Mainboard layout Below illustration identifies the connectors and major components on the Altos G900 mainboard.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!27!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 16 1 System tour The figure below identifies the jumper blocks and pin numbers. The function of each pair of pins is described in the sections that follow. Figure 8 - Mainboard jumpers Boot block jumpers The boot block jumpers are used when updating the BIOS or BMC firmware in the unusual event that the boot block area needs to be updated. These jumpers are not used for routine firmware updates.
BB!H:11!vh!.!FO/cppl!!Qbhf!28!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 17 Jumper block Pins Jumper name - effect when shorted JP3 1-8 Reserved. 9-10 BMC Boot Block Write Enable - Allows the BMC boot block to be overwritten when updating the BMC firmware. 11-12 BIOS Boot Block Write Enable - Allows the BIOS boot block to be overwritten when updating the BIOS. Main jumpers Below table identifies the function of each pin pair on the main jumper blocks (JP4, JP5, and JP6).
BB!H:11!vh!.!FO/cppl!!Qbhf!29!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 18 1 System tour Serial port B jumpers The table identifies the function of each pin pair on the serial port B jumper block (JP25). By default, the serial port B connector is an RJ-45, which has only eight pins and doesn't provide separate DCD and DSR signals. The serial port B jumpers let you configure the DSR and DCD signals passed from the port connector to the inputs of the UART.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 19 System cables This section shows the correct routing of cables from the mainboard to the front subchassis Caution! To avoid possible damage to the cables or internal components, the cables must be routed as shown in the following illustrations. Figure 9 shows the routing of cables from the mainboard to the front subchassis components.
BB!H:11!vh!.!FO/cppl!!Qbhf!31!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 20 1 System tour Label Description Label Description C SCSI hard drive cable F Serial port B cables Figure 10 shows the routing of ribbon cables through the cable clamp. Additional cables are routed behind these ribbon cables as shown in Figure 11.
BB!H:11!vh!.!FO/cppl!!Qbhf!32!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 21 Finally, Figure 11 shows the routing of the cables at the back of the cable clamp, behind the ribbon cables.
BB!H:11!vh!.!FO/cppl!!Qbhf!33!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 22 1 System tour System features The Altos G900 is a powerful server system loaded with a host of new and innovative features. The system offers a new standard for flexible productivity ideal for general business applications, email, web service, file clustering and print services. Processors The Altos G900 server accommodates one to four processors from the Intel® Xeon™ processor family.
BB!H:11!vh!.!FO/cppl!!Qbhf!34!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 23 The mainboard provides active terminators, termination voltage, resettable fuses, and protection diodes for both SCSI channels. You can disable the onboard terminators in BIOS setup. Onboard video The mainboard incorporates an ATI RAGE XL PCI graphics accelerator with 4 MB of video SDRAM that supports all standard IBM VGA modes.
BB!H:11!vh!.!FO/cppl!!Qbhf!35!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 24 • 1 System tour Intel® 82544 NIC that supports 10Base-T, 100Base-TX networks, and 1000BASE-T networks The 82544 controller supports the following features: • Direct 32/64-bit, 33/66-MHz interface to the PCI bus • Integrated IEEE 802.3 1000BASE-T, 100BASE-TX, and 10BASE-T • Integrated third-generation MAC and proven IEEE 803.
BB!H:11!vh!.!FO/cppl!!Qbhf!36!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 25 Power supply The power supply bay comes with two 600-W power supply modules and can accommodate a third module for redundancy. The modules connect through the power distribution board (PDB) and auto-sense input voltage. The power redundant (2+1) configuration allows you to hot-swap a failed power supply without interrupting normal system operation. Warning! The power supply in this product contains no user-serviceable parts.
BB!H:11!vh!.!FO/cppl!!Qbhf!37!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 26 1 System tour ACPI The server supports the Advanced Configuration and Power Interface (ACPI) standard as defined by the ACPI 1.0b and PC97 specifications. An ACPI-aware operating system can put the system into a state where the hard drives spin down, the system fans stop, and all processing is halted.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!39!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This chapter describes the system setup procedures — both for hardware and software aspects.
BB!H:11!vh!.!FO/cppl!!Qbhf!3:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 29 Getting started Checking for damage to the packaging Inspect the packaging container for evidence of mishandling during transit. If the packaging container is damaged, photograph it for reference. Save the packaging container and packing materials in the event you need to package the server for reshipment. Selecting a site Before unpacking and installing the system, select a suitable site for the system for maximum efficiency.
BB!H:11!vh!.!FO/cppl!!Qbhf!41!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 30 • 2 System setup Clearance provided for cooling and airflow. Note: Surge suppressor recommended: In geographic regions that are susceptible to electrical storms, it is strongly recommended that you plug the server into a surge suppressor. Checking the package contents Remove the server from the packaging container and, using the list below, check that all parts and accessories are included.
BB!H:11!vh!.!FO/cppl!!Qbhf!42!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 31 • • System keys (provided inside the system accessory box) • Additional parts or components depending on specific system configuration. System documentation • Acer Altos G900 User’s guide (with system binder) • Acer EasyBUILDTM v5.
BB!H:11!vh!.!FO/cppl!!Qbhf!43!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 32 2 System setup Setting up your system Setup reminders • Do not attempt to modify or use the supplied AC power cord if it is not the exact type required. A product with more than one power supply will have a separate AC power cord for each supply. • The power button on the system does not turn off system AC power. To remove AC power from the system, you must unplug each AC power cord from the wall outlet or power supply.
BB!H:11!vh!.!FO/cppl!!Qbhf!44!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 33 1 Check first to make sure you have not left loose tools or parts inside the system. 2 Check that cables, add-in boards, and other components are properly installed. 3 Attach the panels to the chassis with the screws removed earlier, and tighten them firmly. 4 Insert and lock the padlock to the system to prevent unauthorized access inside the system. 5 Connect all external cables and the AC power cord(s) to the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!45!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 34 9 2 System setup Reinstalling the system access panels: a Installing the access cover to the system boards - see page 52 b Installing the rear access panel - see page 45 You have completed the hardware setup. The remainder of this section discusses software setup and configuration. Refer to page 36.
BB!H:11!vh!.!FO/cppl!!Qbhf!46!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 35 7 Shortly after the splash screen is displayed, POST displays the message "Press to enter Setup…" at the bottom of the screen. At this point, you can press any of the keys identified with an asterisk (*) on the following table, or you can do nothing and wait until the server boots from the CD-ROM. If you enter BIOS setup, the service partition, or the Adaptec® SCSISelect utility, when you exit those features, the server might reboot.
BB!H:11!vh!.!FO/cppl!!Qbhf!47!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 36 2 System setup To do this: Press these keys: Boot from a network using Preboot Execution Environment (PXE). F12 * Remove the splash screen to view the diagnostic messages during POST and display a menu for selecting the boot device. ESC * Using BIOS setup, you can enable the Boot-Time Diagnostic Screen, in which case POST does not display the splash screen.
BB!H:11!vh!.!FO/cppl!!Qbhf!48!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 37 Network teaming features NIC connector and status LEDs The NICs drive LEDs on the network interface connectors that indicate link connection and activity on the LAN and 10- or 100-Mbps operation. The green LED indicates network connection when on and TX/RX activity when blinking. The yellow LED indicates 100-Mbps operation when lit. Note: Using both onboard NICs in a team does not allow the use of NIC 1 for server management access.
BB!H:11!vh!.!FO/cppl!!Qbhf!49!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 38 2 System setup Considerations Windows NT versions prior to 4.0 do not support Adapter Teaming options. Adapter Teaming options require NT 4.0 with Service Pack 4.0 or later (or Service Pack 3.0 and the Windows Hot Fix). In Windows NT, teaming options cannot be implemented on adapters that have been configured for VLANs. NetWare can support teaming options and VLANs on the same adapters.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!51!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This chapter describes detailed procedures for system hardware setup.
BB!H:11!vh!.!FO/cppl!!Qbhf!52!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 41 Installation precautions Before you install any system component, we recommend that you read the following sections. These sections contain important ESD precautions along with preinstallation and post-installation instructions. ESD precautions When installing or removing system components, perform such procedures only at an electrostatic discharge (ESD) workstation, because the server components can be extremely sensitive to ESD.
BB!H:11!vh!.!FO/cppl!!Qbhf!53!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 42 3 Hardware configuration Preinstallation instructions Always observe the following before you install any component: 1 Turn off your system and all the peripherals connected to it. 2 Unplug all cables from the power outlets. 3 Open your system according to the instructions on page 44. 4 Follow the ESD precautions described in this chapter when handling a server component.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!55!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 44 3 Hardware configuration System access panels This section discusses the procedures in: • Removing and replacing the rear access panel • Removing and replacing the front access panel Before removing the access panels To avoid personal injury or property damage, the following safety instructions apply whenever accessing inside the product: 1 Turn off all peripheral devices connected to this product.
BB!H:11!vh!.!FO/cppl!!Qbhf!56!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 45 3 Lift the panel away from the chassis. Figure 12 - Removing the rear access panel To install the rear access panel Note: Before installing the rear access panel, check that you have not left any tool or loose parts inside the system. 1 Position the panel on the chassis so that the panel tabs align with the chassis slots.
BB!H:11!vh!.!FO/cppl!!Qbhf!57!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 46 3 Hardware configuration To remove the front access panel 1 Remove the rear access panel (refer to page 44). 2 Release the two captive panel screws (Figure 13, A). 3 Lift the rear edge of the panel slightly and slide it toward the rear of the chassis. 4 Lift the panel up and off of the chassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!58!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 47 Front subchassis and rear electronics bay The server chassis consists of three parts, which include the following: • Main chassis • Front subchassis (sometimes called the C-tilt) • Rear electronics bay Both the front subchassis and the rear electronics bay swing open. Additionally, you can completely remove them to gain access to the server’s internal components.
BB!H:11!vh!.!FO/cppl!!Qbhf!59!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 48 3 Hardware configuration Figure 14 - Opening the front subchassis and rear electronics bay Label Description A Front subchassis latch B Mainboard cables C Rear electronics bay Removing the front subchassis and rear electronics bay To remove the front subchassis 1 Disconnect all cables attached to the power distribution board and to the mainboard.
BB!H:11!vh!.!FO/cppl!!Qbhf!5:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 49 To remove the electronics bay With the electronics bay open, pull it up and toward the front of the chassis, lifting it clear. Installing the front subchassis and rear electronics bay To install the front subchassis 1 With the front subchassis tilted open about 30°, align the notch in the subchassis with the hinge pins on the main chassis. 2 Lower the subchassis straight down until the hinge pins engage the notches.
BB!H:11!vh!.!FO/cppl!!Qbhf!61!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 50 3 Hardware configuration Closing the front subchassis and rear electronics bay Caution! Before you close the front subchassis or electronics bay, make sure no cables are pinched or otherwise obstructing the front subchassis and rear electronics bay. Excessive cable stress or chafing can cause cables to disconnect and connector pins to bend or break the cable insulation.
BB!H:11!vh!.!FO/cppl!!Qbhf!62!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 51 Accessing the system boards This section discusses the procedures in: • Removing and installing the access cover to the system boards • Removing and installing the memory board • Removing and installing the processor board • Removing and installing the mainboard Caution! A microprocessor and heat sink may be hot if the system has been running. Also, there may be sharp pins and edges on some board and chassis parts.
BB!H:11!vh!.!FO/cppl!!Qbhf!63!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 52 3 Hardware configuration To install the access cover to the system boards 1 Orient the access cover with the captive screws toward the front of the server. 2 Insert the tabs on the rear of the cover into the slots at the rear of the chassis. 3 Press down gently and tighten the captive screws at the front of the cover.
BB!H:11!vh!.!FO/cppl!!Qbhf!64!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 53 To install the memory board 1 Holding the bracket on the top edge of the memory board, insert the board into the guides at both ends of the electronics bay. 2 Align the memory board with the connector on the processor board and press down on the bracket until the board is fully inserted into the connector.
BB!H:11!vh!.!FO/cppl!!Qbhf!65!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 54 3 Hardware configuration Processor board To remove the processor board 1 Rotate the handles on the processor board until they are fully open. 2 Using the handles, tilt the processor board up and remove it from the chassis. Figure 20 - Removing the processor board To install the processor board 1 Insert the tabs on the processor board into the slots on the mainboard bracket (Figure 21, A).
BB!H:11!vh!.!FO/cppl!!Qbhf!66!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 55 Figure 21 - Installing the processor board Mainboard To remove the mainboard 1 Remove all external cables from the mainboard I/O ports at the back of the chassis. 2 Label and disconnect all internal cables connected to the PCI add-in boards. 3 Remove all PCI add-in boards (refer to page 71 and 74). 4 Plastic curtains run the length of the electronics bay separating the PCI add-in cards.
BB!H:11!vh!.!FO/cppl!!Qbhf!67!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 56 3 Hardware configuration For a diagram showing labeled connectors, refer to “Mainboard layout” on page 13. 6 Remove all cables from the cable retention clip on the front of the electronics bay. 7 A plastic retention mechanism for the PCI add-in cards is fastened to the front of the electronics bay by three clips (Figure 22, A). Release each clip by pressing down on the tab and remove the retention mechanism.
BB!H:11!vh!.!FO/cppl!!Qbhf!68!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 57 9 Label Description Label Description A Tabs (3) on retention mechanism C Overlay tab (1 of 2) B Protective overlay D Overlay screw Remove the six screws, the plastic overlay, and the two processor board mounting brackets that attach the mainboard to the electronics bay (Figure 23, A). 10 Lifting the board slightly, slide the mainboard toward the front of the chassis until the I/O ports clear the chassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!69!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 58 3 Hardware configuration To install the mainboard 1 With the rear of the electronics bay closest to you and the mainboard oriented so that the I/O connectors line up with the cutout in the back left of the chassis (Figure 23), lower the right end of the mainboard into the electronics bay and slip the board edge into the slots of the foam panel (Figure 23, B).
BB!H:11!vh!.!FO/cppl!!Qbhf!6:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 59 6 Connect all internal cables to the mainboard. To make sure you route the cables correctly, refer to “Front panel board” on page 89. If the cables are not routed correctly, you won't be able to close the front subchassis. 7 Install the PCI add-in board curtains as follows: a At the back of the electronics bay, slide the end of a curtain with the locking tab into the topmost square hole adjacent to any add-in board expansion slot.
BB!H:11!vh!.!FO/cppl!!Qbhf!71!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 60 3 Hardware configuration Memory This section includes instructions for removing and installing DIMMs on the memory board. DIMM sequence Load the DIMMs in the following order: • Bank 1: DIMMs #1, 2, 3, and 4 • Bank 2: DIMMs #5, 6, 7, and 8 • Bank 3: DIMMs #9, 10, 11, and 12 Always fill banks completely. Partially filled banks are ignored by the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!72!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 61 4 Orient the DIMM so that the notch in the bottom edge of the DIMM aligns with the keyed socket on the memory board. 5 Insert the bottom edge of the DIMM into the socket and press down firmly on the DIMM until it seats correctly. The plastic ejector levers should snap into place when the DIMM is seated. Figure 25 - Installing a DIMM 6 Make sure that the plastic ejector levers on the socket ends are fully closed.
BB!H:11!vh!.!FO/cppl!!Qbhf!73!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 62 3 3 Hardware configuration Hold the DIMM only by its edges, being careful not to touch its components or gold edge connectors. Carefully lift it away from the socket and store it in an antistatic package.
BB!H:11!vh!.!FO/cppl!!Qbhf!74!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 63 Processors This section includes instructions for installing and removing processors and heat sinks. Processor sequence You must install a processor in processor socket 1. When installing multiple processors, populate the processor sockets in the order shown in the figure below. Figure 27 - Correct order in loading processors Important: If you are not using processor sockets 3 and 4, leave the foam block in place.
BB!H:11!vh!.!FO/cppl!!Qbhf!75!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 64 3 Hardware configuration To install processors 1 Raise the locking bar on the socket. Figure 28 - Raising the locking bar 2 Orient the processor so that the triangle on the corner of the processor aligns with the triangle on the corner of the socket. 3 Aligning the pins of the processor with the socket, insert the processor into the socket. The processor should drop into the socket without requiring any force.
BB!H:11!vh!.!FO/cppl!!Qbhf!76!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 65 5 Following the instructions packaged with the applicator, apply thermal grease to the processor. 6 Insert the heat sink (Figure 30, A) into the air baffle and place it on top of the processor. 7 Install both heat sink retention clips (Figure 30, D) as follows: a Place the heat sink clip on the center tab of the retention module and slide the clip to the right to engage the center tab.
BB!H:11!vh!.!FO/cppl!!Qbhf!77!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 66 1 3 Hardware configuration Remove both heat sink clips as follows: a Insert the heat sink clip extraction tool (refer to page 43) into the slot at one end of the clip. b Press down on the tool until the clip clears the bottom edge of the tab on the retention module and rotate the tool until the end of the clip is free of the tab. c Using the clip extraction tool, release the other end of the clip.
BB!H:11!vh!.!FO/cppl!!Qbhf!78!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 67 PCI add-in boards PCI add-in board locations The Altos G900 server supports four hot-plug PCI add-in boards and four non-hot-plug PCI add-in boards.
BB!H:11!vh!.!FO/cppl!!Qbhf!79!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 68 3 Hardware configuration Operating system support for hot-plug add-in boards Some operating systems support hot-plugging PCI add-in boards and some do not. Operating system support is provided by a driver that you must install when setting up your server. Hot-plug drivers are available on the Drivers directory of the System CD. The driver files on the CD include information on installing and using the hot-plug software.
BB!H:11!vh!.!FO/cppl!!Qbhf!7:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 69 Figure 33 - Hot-plug PCI add-in board status indicators Installing and removing a hot-plug PCI add-in board To install a hot-plug PCI add-in board 1 Remove the rear access panel (refer to page 44). 2 If the LED for the slot indicates that power to the slot is on, turn it off by using the PCI hot-plug application software on your system. The LED adjacent to the slot should now be off.
BB!H:11!vh!.!FO/cppl!!Qbhf!81!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 70 5 3 Hardware configuration Prepare the new PCI board for installation: a Remove the add-in board from its protective wrapper. Be careful not to touch the components or gold edge connectors. Place the add-in board with the component side up on an antistatic surface. b Record the serial number of the add-in board in your equipment log. For a sample equipment log sheet, refer to page 195.
BB!H:11!vh!.!FO/cppl!!Qbhf!82!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 71 10 Turn on power to the add-in board using the PCI hot-plug application software on your system. To remove a hot-plug PCI add-in board 1 Remove the rear access panel (refer to page 44). 2 If the LED for the slot indicates that power to the slot is on, turn it off by using the PCI hot-plug application software on your system. The LED adjacent to the slot should now be off.
BB!H:11!vh!.!FO/cppl!!Qbhf!83!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 72 6 3 Hardware configuration If you are not reinstalling a board in the same slot, install an expansion slot cover and reinstall the rear access panel (refer to page 45). If you are installing a new board, follow the instructions on page 69. Installing and removing a PCI add-in board in a non-hot-plug slot Caution! The PCI add-in board slots located under the system board access panel are not hot-plug slots.
BB!H:11!vh!.!FO/cppl!!Qbhf!84!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 73 To install a PCI add-in board in a non-hot-plug slot 1 Disconnect the AC power cords from the power source or wall outlets. 2 Turn off all peripheral devices connected to the server system. 3 Remove the rear access panel (refer to page 44) and the system board access panel (refer to page 51). 4 If necessary, remove and save the expansion slot cover.
BB!H:11!vh!.!FO/cppl!!Qbhf!85!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 74 3 Hardware configuration To remove a PCI add-in board from a non-hot-plug slot 1 Disconnect the AC power cords from the power source or wall outlets. 2 Turn off all peripheral devices connected to the server system. 3 Remove the rear access panel (refer to page 44) and the system board access panel (refer to page 51). 4 Release the latches on the front and rear retention mechanisms.
BB!H:11!vh!.!FO/cppl!!Qbhf!86!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 75 Hot-swap SCSI drives Hot-swap drives are installed in carriers that fit into the hot-swap drive bay. This section describes the LED status indicators for the drive bays and gives instructions for using the drive carriers to install and remove drives. Checking a hot-swap SCSI drive status indicator Each hot-swap SCSI drive slot has a LED that indicates drive status. To view the LEDs, open the front access door of the bezel.
BB!H:11!vh!.!FO/cppl!!Qbhf!87!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 76 3 Hardware configuration The table below lists the LED states and the drive status indicated by each state. LED state Status Solid green The hard drive is present and powered on. Flashing green The hard drive is active. Solid yellow There is an asserted fault status on the hard drive. Flashing yellow A rebuild of the hard drive is in progress. Off The hard drive is not powered on.
BB!H:11!vh!.!FO/cppl!!Qbhf!88!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 77 Label Description Label Description A Air Baffle C Plastic rail B Screw D Plastic rail 2 Remove the hard drive from its wrapper and place it on an antistatic surface. 3 Record the new drive model and serial number in your equipment log. For a sample equipment log sheet, refer to page 195. 4 Place the drive in the carrier with the component side down.
BB!H:11!vh!.!FO/cppl!!Qbhf!89!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 78 3 Hardware configuration Label Description A SCA connector B Drive C Carrier D Plastic rail E Screw To remove a hot-swap drive from a carrier 1 Remove the carrier and drive from the drive bay. 2 Remove the four screws that secure the drive to the carrier. 3 Place the drive on an antistatic surface. 4 If you are going to reinstall the carrier without a drive, you must first reinstall the air baffle in the carrier.
BB!H:11!vh!.!FO/cppl!!Qbhf!8:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 79 3 Carefully pull on the carrier handle and slide the carrier out of the bay. Figure 40 - Removing a drive carrier Label Description A Handle B Latch C Locking slot 4 Install a new drive into the carrier (refer to page 76). 5 Hold the carrier handle in the fully open position and slide the carrier into the desired bay.
BB!H:11!vh!.!FO/cppl!!Qbhf!91!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 80 7 3 Hardware configuration Push the handle closed until it clicks into position.
BB!H:11!vh!.!FO/cppl!!Qbhf!92!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 81 DC power supplies The power supply bay accommodates up to three power supply modules. The bay contains a power distribution board (PDB) that manages the delivery of power from the power supply modules. Checking the power supply LED status indicators The figure below shows the three power supply LED status indicators.
BB!H:11!vh!.!FO/cppl!!Qbhf!93!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 82 3 Hardware configuration Refer to the table below for a list of LED states and the power supply status indicated by each state. Power (Green) Predictive fail (Amber) Fail (Amber) Status Off Off Off No power to all power supplies. Off Off On Power supply failure or no power to this power supply. Blinking Off Off AC power present, standby outputs on. On Off Off Power supply on, DC outputs normal.
BB!H:11!vh!.!FO/cppl!!Qbhf!94!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 83 Caution! To avoid damaging the module, do not tilt or twist the power supply module as you pull it from the power supply bay. The module disengaging from its connector causes the initial resistance you will feel. Use even, steady force to remove the module. Figure 43 - Removing a power supply module Label Description Label Description A Screws B Latch handle 4 Unplug the power cord from the power supply.
BB!H:11!vh!.!FO/cppl!!Qbhf!95!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 84 3 Hardware configuration To install a power supply module 1 If present, remove the filler panel from the vacant slot. 2 Holding the power supply latch handle in the open position, slide the power supply module into the vacant slot until you feel resistance. Caution! The module engaging its connector causes the resistance. To avoid damaging the module, do not tilt or twist the power supply module as you push it into the connector.
BB!H:11!vh!.!FO/cppl!!Qbhf!96!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 85 Cooling system fans The Altos G900 server accommodates six hot-swap fan modules. Caution! Don't remove a fan module while the server is powered on unless you have a replacement unit available. Once you remove a fan module from the system, replace it within five minutes. Vacant spaces alter airflow patterns in the server system and can cause overheating and damage to system components.
BB!H:11!vh!.!FO/cppl!!Qbhf!97!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 86 3 Hardware configuration Removing and installing a fan module Figure 45 - Removing and installing a fan module To remove a fan module 1 Remove the front access panel (refer to page 46). 2 Grasp the fan module and pull it straight out of the foam baffle. To install a fan module Note: If you are replacing a failed fan module, wait for the fan status LED to turn off. Generally, this will take less than ten seconds.
BB!H:11!vh!.!FO/cppl!!Qbhf!98!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 87 Backup battery The lithium battery on the mainboard powers the real-time clock (RTC) in the absence of power. When the battery starts to weaken, it loses voltage, and the server settings stored in CMOS RAM in the RTC (for example, the date and time) might be incorrect. For a list of approved replacement batteries, contact your customer service representative or dealer. Warning! Danger of explosion if battery is incorrectly replaced.
BB!H:11!vh!.!FO/cppl!!Qbhf!99!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 88 3 Hardware configuration Figure 46 - Removing the battery 6 Remove the battery from its socket. 7 Dispose of the battery according to local ordinance. 8 Remove the new lithium battery from its package. 9 Being careful to observe the correct polarity, lay the battery in the socket, inserting one edge of the battery under the large corner tabs. 10 Push the battery down until it locks into the socket.
BB!H:11!vh!.!FO/cppl!!Qbhf!9:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 89 Front panel board For a description of the features on the front panel board, see “Front control panel” on page 8. Installing the front panel board 1 Turn off power to the server and unplug the AC power cords from the power source. 2 Remove the front access panel (refer to page 46). 3 Remove the fan modules and the foam fan baffle (refer to page 86).
BB!H:11!vh!.!FO/cppl!!Qbhf!:1!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 90 3 Hardware configuration Label Description Label Description A Front panel board cable D Screw B USB and serial port cables E Snap-top standoff C Chassis intrusion cables F Slot in chassis 8 Slide the notched end of the new front panel board into the slot in the front subchassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!:2!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 91 Diskette drive Replacing the diskette drive 1 Turn off power to the server and unplug the AC power cords from the power source. 2 Remove the front access panel (refer to page 46). 3 Remove the fan modules and the foam fan baffle (refer to page 86). 4 Disconnect the power and signal cables from the back of the diskette drive. 5 Remove the screw that secures the diskette drive bracket to the chassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!:3!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 92 3 Hardware configuration Label Description A Power cable B Data cable C Screw Note: If you are not installing a replacement device, install a metal EMI shield on the bay to maintain proper cooling and EMI shielding. 10 Remove the new diskette drive from its protective wrapper and place it on an antistatic surface. 11 Record the drive model and serial numbers in your equipment log.
BB!H:11!vh!.!FO/cppl!!Qbhf!:4!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 93 15 Slide the bracket toward the front of the drive and engage the locating pins on each side of the bracket in the mating holes in the drive frame. 16 Position the bracket and drive so that the front of the drive fits correctly in the opening in the front subchassis and the mounting screw hole in the back of the bracket is aligned with the mating hole in the front subchassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!:5!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 94 3 Hardware configuration 5.25-inch peripheral drives This section provides information and instructions for installing and removing devices from the 5.25-inch peripheral bay. Preliminary considerations Caution! You should not install hard drives in the 5.25-inch peripheral drive bays for two reasons: - The drives cannot be properly cooled in this location.
BB!H:11!vh!.!FO/cppl!!Qbhf!:6!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 95 the SCSI bus specification. Otherwise, the bus might be unreliable and data might become corrupted or devices might not work properly. EMC compliance of 5.25-inch removable media device bays Integration of the 5.25-inch peripheral drive bay can affect EMC compliance and is a regulated activity. Except as noted here, any changes to the bay configuration could result in non-compliance with EMC regulations in your area.
BB!H:11!vh!.!FO/cppl!!Qbhf!:7!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 96 3 Hardware configuration To remove a a 5.25-inch peripheral drive 1 Turn off power to the server and unplug the AC power cords from the power source. 2 Remove the front access panel (refer to page 46). 3 Remove the fan modules and the foam fan baffle (refer to page 86). 4 Disconnect the power and data cables from the back of the drive.
BB!H:11!vh!.!FO/cppl!!Qbhf!:8!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 97 4 If the drive bay is covered by a metal EMI shield, insert your finger in the large hole in one end of the shield and pull the shield from the chassis. Save the shield. 5 If the drive bay has an existing drive installed, remove the drive (see page 96) and remove the slide rails attached to the sides of the drive. Save the rails and screws. 6 Remove the new drive from its protective wrapper and place it on an antistatic surface.
BB!H:11!vh!.!FO/cppl!!Qbhf!:9!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 98 3 Hardware configuration Hot-swap drive bays The hot swap drive bay assemblies come with a backplane board and a fan. Each drive slot contains a drive carrier with a plastic air baffle. Removing and installing a hot-swap drive bay To remove a hot-swap drive bay 1 Turn off power to the server and unplug the AC power cords from the power source. 2 Open and remove the front subchassis (refer to page 47 and 48).
BB!H:11!vh!.!FO/cppl!!Qbhf!::!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 99 Label Description Label Description A Screws C Power cables B I2C cable D Fan cable C Chassis intrusion cables F Slot in chassis Note: Although not necessary, for easier handling, you might want to remove any drives installed in the drive bay assembly before proceeding. 5 If both hot swap drive bays are installed, loosen two of the screws that secure one side of the other drive bay to the front subchassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!211!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 100 3 Hardware configuration 4 If another hot-swap drive bay is already installed, loosen two of the screws that secure one side of the other drive bay to the front subchassis. Loosening the other drive bay allows the drive bay enclosure to expand slightly, making it easier to remove the drive bay assembly.
BB!H:11!vh!.!FO/cppl!!Qbhf!212!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 101 Power distribution board Replacing the power distribution board 1 Remove the front and rear access covers (refer to page 46 and page 44). 2 Open the front subchassis and remove the electronics bay (refer to page 47 and page 49). 3 Partially remove the power supplies (refer to page 82) to disengage the power supply connectors from the power distribution board. 4 Disconnect the cables from the power distribution board.
BB!H:11!vh!.!FO/cppl!!Qbhf!213!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 102 3 Hardware configuration Label Description Label Description A Power supply module B Screws 7 8 Remove the two plastic rivets and the plastic overlay from the power distribution board. 9 Attach the plastic overlay to the new power distribution board using the two plastic rivets. 10 Grasp the new power distribution board and overlay with the power supply connectors facing the power supply bays.
BB!H:11!vh!.!FO/cppl!!Qbhf!214!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 103 Fan distribution board The fan distribution board is located in the foam fan baffle and provides power and signal circuitry for the hot-swappable fans. Replacing the fan distribution board 1 Remove the front access panel (page 46). 2 Remove all fan modules from the foam fan baffle (page 86). 3 Remove the mainboard ribbon cable and the power cable from the fan distribution board.
BB!H:11!vh!.!FO/cppl!!Qbhf!215!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 104 3 Hardware configuration 8 Gently press outward on two corners of the foam to spread open the fan distribution board slot in the foam fan baffle and rotate the board into place. 9 Connect the mainboard ribbon cable and the power cable. 10 Install the fan modules. 11 Install the front access panel.
BB!H:11!vh!.!FO/cppl!!Qbhf!216!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 105 Foam fan baffle Removing and installing the foam fan baffle To remove the foam fan baffle 1 Remove the front access panel (page 46). 2 Remove all fan modules from the foam fan baffle (page 86). 3 Remove the fan distribution board (page 103). 4 Gently bend the ends of the foam baffle (Figure 54, A) toward each other to release the baffle notches from the tabs of the front subchassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!217!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 106 3 Hardware configuration To install the foam fan baffle 1 Position the fan baffle so the holes in the bottom of the baffle are aligned with the four hot swap drive bay mounting screws (or holes) in the front subchassis. 2 Gently bend back the ends of the foam baffle (Figure 54, A), then push down and slide the baffle straight into the chassis until the tabs on the front subchassis mate with the corresponding notches in the baffle.
BB!H:11!vh!.!FO/cppl!!Qbhf!218!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 107 Hot-plug indicator board Replacing the hot-plug indicator board 1 Remove the rear access panel (refer to page 44). 2 Disconnect the ribbon cable from the end of the hot-plug indicator board. 3 Remove the two plastic rivets that secure the board to the electronics bay (Figure 55, C). 4 The end of the board where the cable attaches is inserted into a notch in the chassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!219!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 108 3 Hardware configuration Label Description B Rivet sleeve C Rivet 5 Place the end of the new hot-plug indicator board into the notched bracket in the back of the electronics bay. 6 Align the plastic rivet sleeves in the chassis back panel with the two mounting holes in the board and press the sleeves into the holes.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!221!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This chapter gives information about the system BIOS and discusses how to configure the system by changing the settings of the BIOS parameters.
BB!H:11!vh!.!FO/cppl!!Qbhf!222!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 111 BIOS setup Use BIOS setup to change the system configuration defaults. You can run BIOS setup with or without an operating system being present. BIOS setup stores most of the configuration values in the batterybacked CMOS; the remainder are stored in flash memory. The values take effect when the system is booted. POST uses these values to configure the hardware.
BB!H:11!vh!.!FO/cppl!!Qbhf!223!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 112 4 BIOS setup To clear the CMOS memory using the front panel buttons 1 Power down the server. 2 Press the Reset button and hold it down for four seconds or more; while holding down the reset button, press the power button. 3 Release both buttons at the same time. To clear the CMOS memory using CMOS Clear jumper 1 Power down the server. 2 Install a jumper on the CMOS Clear jumper pins. 3 Boot the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!224!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 113 Press: To: F9 Reset to BIOS setup defaults F10 Save and exit BIOS setup When an option is grayed out and not accessible, you cannot change or configure the option in that menu screen for one of the following reasons: • The option is auto-configured or auto-detected. • The field is informational only. • The field is password-protected and is accessible only by the User or Administrator.
BB!H:11!vh!.!FO/cppl!!Qbhf!225!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 114 4 BIOS setup Main The Main menu displays basic and important information about the system. These information is necessary for troubleshooting and may be required when asking for technical support. Parameter Description Option System TIme Sets the time following the hour-minute-second format. Hour: 00 to 23 Sets the date following the weekday-month-day-year format.
BB!H:11!vh!.!FO/cppl!!Qbhf!226!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 115 Parameter Description Option Hard Disk Pre-delay Sets an interval time between boot up and BIOS access of the hard drive. This is to prevent the system from hanging up when BIOS accessed it prior to drive initialization. Disabled 3 seconds 6 seconds 9 seconds 12 seconds 15 seconds 21 seconds 30 seconds Primary IDE Master Press Enter to access the Primary IDE Master submenu.
BB!H:11!vh!.!FO/cppl!!Qbhf!227!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 116 4 BIOS setup Primary IDE Master/Slave These two IDE submenus let you define the parameter settings related to the IDE drives.
BB!H:11!vh!.!FO/cppl!!Qbhf!228!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 117 Parameter Description Option Type Driver type Auto User 1-39 CD-ROM ATAPI Removable Multi-Sector Transfers Enhances disk performance depending on the hard disk in use. If you set this parameter to Auto, BIOS setup automatically detects if the installed hard disk drive supports the Block Mode function. If supported, it allows data transfer in blocks (multiple sectors) at a rate of 256 bytes per cycle.
BB!H:11!vh!.!FO/cppl!!Qbhf!229!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 118 4 BIOS setup Processor Settings This submenu lets you set parameter settings related to the installed processor(s). Parameter Description Processor Retest Clears the processors’ historical status and resets all processors during the next bootup. Options include Yes and No. Processor Speed Settings The processor speed is the speed at which a microprocessor executes instructions.
BB!H:11!vh!.!FO/cppl!!Qbhf!22:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 119 Advanced The Advanced menu contains parameter values that define how the system behaves on startup. Warning! Be cautious in setting parameter values in the Advanced menu as any incorrect value may cause the system to malfunction. Parameter Description Memory Configuration Press Enter to access the Memory Configuration submenu. PCI Configuration Press Enter to access the PCI Configuration submenu.
BB!H:11!vh!.!FO/cppl!!Qbhf!231!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 120 4 BIOS setup Parameter Description Option Reset Configuration Data Select whether to delete data stored in the ESCD (Extended System Configuration Data) area. When this parameter is set to Yes, current data is deleted. No Yes NumLock Activates the Num Lock function upon booting. Off Select whether to boot or pause the system when a memory or processor error occurs.
BB!H:11!vh!.!FO/cppl!!Qbhf!232!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 121 Memory Configuration This submenu allows you to configure the advanced system memory functions. Parameter Description Option DIMM Group # 1/2/3 Status Indicates the status of a particular bank of memory modules. Normal Memory Retest Clears the memory error status. No Yes Extended RAM Step Selects the type of extended testing to perform on the RAM.
BB!H:11!vh!.!FO/cppl!!Qbhf!233!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 122 4 BIOS setup PCI Configuration This submenu lets you specify the settings for the PCI devices. Press Enter to access the submenu screen of the parameters shown in the screen below.
BB!H:11!vh!.!FO/cppl!!Qbhf!234!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 123 Hot-plug PCI Control This submenu lets you specify the settings for the PCI hot-plug slots. Parameter Description Option Reserving memory space for PHP Determines the memory space to be assigned for each empty PHP (PCI Hot Plug) slot.
BB!H:11!vh!.!FO/cppl!!Qbhf!235!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 124 4 BIOS setup Empty Bus Default Speed This submenu lets you specify the speed and capability settings of the PCI hot-plug slots. Parameter Description PCI Slots 5 - 6 PCI Slots 7 - 8 If no card is present in any of the PCI-X capable PCI bus, the speed and capability setting will automatically be assigned.
BB!H:11!vh!.!FO/cppl!!Qbhf!236!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 125 Embedded SCSI This submenu lets you specify the settings of the onboard SCSI controller.
BB!H:11!vh!.!FO/cppl!!Qbhf!237!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 126 4 BIOS setup Embedded NIC 1 (10/100) This submenu lets you specify the settings of the embedded LAN controller 1.
BB!H:11!vh!.!FO/cppl!!Qbhf!238!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 127 Embedded NIC 2 (Gbit) This submenu lets you specify the settings of the embedded LAN controller 2.
BB!H:11!vh!.!FO/cppl!!Qbhf!239!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 128 4 BIOS setup Embedded Voice Controller This submenu lets you specify the settings of the embedded voice controller.
BB!H:11!vh!.!FO/cppl!!Qbhf!23:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 129 PCI Slot 1 - 8 This submenu lets you initialize device expansion ROM. I/O Device Configuration This submenu lets you define the parameter settings for the system’s parallel and serial ports.
BB!H:11!vh!.!FO/cppl!!Qbhf!241!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 130 4 BIOS setup Parameter Description Option Serial Port A/B Base I/O Address Interrupt Base address and IRQ (interrupt request) setting for serial port A/B.
BB!H:11!vh!.!FO/cppl!!Qbhf!242!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 131 Advanced Chipset Control This submenu lets you specify the settings for the system’s wake-up functions .
BB!H:11!vh!.!FO/cppl!!Qbhf!243!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 132 4 BIOS setup Security The Security menu allows you to safeguard and protect the system from unauthorized use by setting up access passwords. Parameter Description Option User Password is Secures your system against unauthorized use. Once you set this password, you have to type it whenever you boot the system. User password is available only when a Supervisor password is set.
BB!H:11!vh!.!FO/cppl!!Qbhf!244!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 133 Parameter Description Option Secure Mode Timer Set a period of keyboard/mouse inactivity before Secure Mode is activated. 2 min 5 min 10 min 20 min 1 hr 2 hr Hot Key (CTRL + ALT + _) Select a key to be used in combination with (CTRL + ALT + _) to serve as a hot key in activating Secure Mode. Options include A- Z and 0 - 9. Note: Selected key combination should not conflict with a key combination used by a system application.
BB!H:11!vh!.!FO/cppl!!Qbhf!245!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 134 4 BIOS setup To set a security password 1 Use the up/down keys to highlight a set password parameter then press Enter. A password box will appear. 2 Type a password. The password may consist of up to six alphanumeric characters (A-Z, a-z, 0-9). 3 Retype the password to verify the first entry. 4 Press Enter. After setting the password, the system automatically changes the chosen password parameter to Set.
BB!H:11!vh!.!FO/cppl!!Qbhf!246!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 135 To change the Supervisor/User password 1 Use the up/down keys to highlight either set password parameters then press Enter. 2 Type the original password then press Enter. 3 Type a new password then press Enter. 4 Retype the password to verify the first entry then press Enter again. To remove the User/Supervisor password 1 Use the up/down keys to highlight either set password parameters then press Enter.
BB!H:11!vh!.!FO/cppl!!Qbhf!247!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 136 4 BIOS setup Server The Server menu allows you to configure parameter settings related to server management. Parameter Description Option System Management Press Enter to access the System Management submenu. Console Redirection Press Enter to access the Console Redirection submenu. Service Partition Type Displays the current service partition type.
BB!H:11!vh!.!FO/cppl!!Qbhf!248!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 137 Parameter Description Option FRB-2 Policy Selects an action to implement when an FRB-2 failure occurs, that is whether to disable the BSP (Boot Strap Processor) or not. An FRB-2 failure occurs if the system fails to respond after six minutes of bootup attempt. Disable FRB2 Timer Disable BSP Thermal Sensor Specifies whether BIOS will disable boot when system temperature is outside the safe range.
BB!H:11!vh!.!FO/cppl!!Qbhf!249!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 138 4 BIOS setup System Management This submenu displays a list of information regarding the system hardware. All parameters are non-configurable in user mode.
BB!H:11!vh!.!FO/cppl!!Qbhf!24:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 139 Console Redirection This submenu lets you specify the settings for connecting to the RDM Manager station. Parameter Description Option Serial Port Address Selects the serial port to be used for connecting to the RDM Manager. Disabled Baud Rate This parameter lets you set the RDM connection transfer rate.
BB!H:11!vh!.!FO/cppl!!Qbhf!251!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 140 4 BIOS setup Boot The Boot menu displays a list of removable device(s) and hard disk(s) available in the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!252!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 141 Exit The Exit menu displays the various options to quit from the BIOS setup. Highlight any of the exit options then press Enter. Parameter Description Exit Saving Changes Saves changes made and close the BIOS setup. Exit Discarding Changes Discards changes made and close the BIOS setup. Load Setup Defaults Loads the factory-default settings for all BIOS setup parameters.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!255!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This appendix describes the procedures for configuring the system in a rack-mount fashion.
BB!H:11!vh!.!FO/cppl!!Qbhf!256!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 145 System rack installation The Altos G900 server system is available in both rack-mount and tower configuration. A rack mount kit is available for customers who want to convert a tower-mounted system to rack-model design. To purchase a rack mount kit, contact your local Acer representative or order directly from www.acer.com.tw. The figure below shows the Altos G900 server in a rack-mount and tower position.
BB!H:11!vh!.!FO/cppl!!Qbhf!257!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 146 • Appendix A: System rack installation Bag of mounting hardware (bushings and screws) You must also purchase the rack-mount rail kit for the Altos G900 server platform to complete the conversion from tower to a rackmount configuration.
BB!H:11!vh!.!FO/cppl!!Qbhf!258!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 147 assemblies. The anchors must be able to withstand a force of up to 113 kg (250 pounds). You must also consider the weight of any other device installed in the rack. MAIN AC POWER DISCONNECT: You are responsible for installing an AC power disconnect for the entire rack unit. This main disconnect must be readily accessible, and it must be labeled as a controlling power to the entire unit, not just to the server(s).
BB!H:11!vh!.!FO/cppl!!Qbhf!259!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 148 Appendix A: System rack installation Rack conversion procedures This section describes the procedures to install the contents of the rack conversion kit. Unless otherwise specified, all references to chassis directions (top, bottom, left, right, front, and rear) refer to a chassis in rack orientation when you are facing the front of the chassis.
BB!H:11!vh!.!FO/cppl!!Qbhf!25:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 149 Figure 58 - Removing the bottom panel Removing the left panel 1 Loosen the screw (Figure 59, A) on the rear edge of the left panel. 2 Slide the cover toward the rear of the chassis (Figure 59, B) and lift it off.
BB!H:11!vh!.!FO/cppl!!Qbhf!261!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 150 Appendix A: System rack installation 3 Figure 59 - Removing the left panel Removing the original tower bezel You must remove the bezel that originally came with the tower configuration of the Altos G900 server platform and, later in the installation, replace it with the bezel from the rack conversion kit. 1 Move the chassis so the door hangs over the edge of your workbench. 2 Open the door.
BB!H:11!vh!.!FO/cppl!!Qbhf!262!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 151 Figure 60 - Removing the original tower bezel Note: Do not throw away the keys from the original tower bezel. The keys and lock on each bezel are paired together and will not work with a different bezel. The lockset and the keys both have a stamped number on them, and these numbers must match for the keys to work.
BB!H:11!vh!.!FO/cppl!!Qbhf!263!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 152 3 Appendix A: System rack installation Remove the screw (Figure 61, B) that holds the rear foot to the chassis, slide the foot upward, then remove the foot. Figure 61 - Removing the feet Note: If the rack system will ever be converted back to a tower configuration, be sure to keep all unused tower parts—the tower bezel, keys, bottom and left panels, feet, and two screws—for future use.
BB!H:11!vh!.!FO/cppl!!Qbhf!264!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 153 4 Insert each tab in the corresponding slot and push the bezel against the front of the chassis until it is fully seated. Figure 62 - Installing the rack bezel Installing the bushings on the chassis You need six bushings and screws to install the rack rails on the system, three per side. The two extra bushings and screws are for use as spares.
BB!H:11!vh!.!FO/cppl!!Qbhf!265!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 154 3 Appendix A: System rack installation Attach the three bushings on the left frame wall of the chassis (Figure 63, E) in the pattern shown in Figure 65 using the same procedure described in step 1. Figure 63- Installing the bushings Installing the handles and rails To complete the installation the rack conversion kit contents, you must also have the rack-mount rail kit.
BB!H:11!vh!.!FO/cppl!!Qbhf!266!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 155 1 Extend the inner rail out of the rail assembly until the component rail release latch clicks. Hold down the latch and slide out the inner rail out of the rail assembly. Do the same thing to the other assembly rail. Figure 64 - Sliding out the inner rails 2 Install the outer rails to the rack.
BB!H:11!vh!.!FO/cppl!!Qbhf!267!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 156 3 Appendix A: System rack installation Attach the inner rails to the server. Figure 66 - Installing the inner rails to the server 4 Attach the rack handles to the server.
BB!H:11!vh!.!FO/cppl!!Qbhf!268!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 157 5 Slide the server into the rack.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!271!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This appendix gives information about the software programs and utilities bundled with your system.
BB!H:11!vh!.!FO/cppl!!Qbhf!272!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 161 Software and utilities Your system came bundled with several software programs and utilities designed to streamline your server's operations. These utilities may include any of the following: • BIOS setup For modifying server board set features, including setting time, date, and system passwords; setting the boot device priority; configuring the diskette drive and serial ports; and enabling the SCSI BIOS and system management features.
BB!H:11!vh!.!FO/cppl!!Qbhf!273!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 162 Appendix B: System management Integrated hardware system management The figure below is a simplified diagram of the system management features integrated into the server. Figure 69 - Integrated system management Baseboard management controller The Altos G900 system incorporates a baseboard management controller (BMC), which is a dedicated microcontroller for system management activities.
BB!H:11!vh!.!FO/cppl!!Qbhf!274!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 163 • Provides the main front panel control functions (power on/off, reset, and so on). Field replaceable units and sensor data records Field replaceable units (FRUs) are major modules in the chassis that contain active electronic circuitry. FRUs can store information such as board serial number, part number, name, and asset tag that can be read using the System Setup Utility (refer to page 166).
BB!H:11!vh!.!FO/cppl!!Qbhf!275!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 164 Appendix B: System management Platform event management Events can trigger alerts and other actions by the BMC.
BB!H:11!vh!.!FO/cppl!!Qbhf!276!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 165 Emergency management port The emergency management port (EMP) refers to the use of the COM2 port, with either an external modem or direct serial connection, for remote management. The BMC controls the port and interfaces with remote access software, such as the Direct Platform Control application in ASMe. Note: For more information, refer to the ASMe User’s guide.
BB!H:11!vh!.!FO/cppl!!Qbhf!277!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 166 Appendix B: System management System Setup Utility The System Setup Utility (SSU) program is located on the System CD.
BB!H:11!vh!.!FO/cppl!!Qbhf!278!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 167 Alternatively, if you have a workstation with the Microsoft Windows operating system, you can insert the CD into that system and create the diskettes on that system. Running the SSU When the SSU starts in the default local execution mode, it accepts input from the keyboard or mouse. The SSU presents a VGA-based GUI (graphical user interface) on the primary monitor.
BB!H:11!vh!.!FO/cppl!!Qbhf!279!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 168 Appendix B: System management Working with the GUI You can access features of the GUI using the mouse or keyboard: • Mouse • • Click once to choose menu items and buttons or to select items in a list, such as the Available Tasks list. • To run a list item, such as one of from the Available Tasks list, select the item and click OK or double-click the item.
BB!H:11!vh!.!FO/cppl!!Qbhf!27:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 169 • Mode Lets you set the desired expertise level: novice, intermediate, or expert. The expertise level determines which tasks are visible in the Available Tasks section and which actions each task performs. For a new mode setting to take effect, you must exit the SSU and restart it. • Language Lets you change the text in the SSU interface to the appropriate language.
BB!H:11!vh!.!FO/cppl!!Qbhf!281!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 170 Appendix B: System management Setting the admin password The Admin Password button lets you set or change the admin password used by both the SSU and the system BIOS. This option is not available if both an admin and a user password are set and you entered only the user password when you started the SSU. All changes to the admin password take effect immediately.
BB!H:11!vh!.!FO/cppl!!Qbhf!282!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 171 Setting security options 1 In the Security window, click the Options button. 2 For each option, select the desired setting from the list. The options are: 3 • Security Hot Key The key combination that can be used to put the server into secure mode. • Secure Mode Timer If no keyboard or mouse activity occurs during the chosen time interval, the server enters secure mode.
BB!H:11!vh!.!FO/cppl!!Qbhf!283!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 172 3 Appendix B: System management Use the File and SEL menu items to work with the SEL information: • Open Views data from a previously saved SEL file. • Save As Saves the currently loaded SEL data to a file. • Properties Displays information about the SEL. • Clear SEL Clears the SEL data from the nonvolatile storage area. • Reload Refreshes the display by reading the current SEL entries from the server.
BB!H:11!vh!.!FO/cppl!!Qbhf!284!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 173 • Properties Displays the number of FRU devices in the system and the number being displayed. Only FRU devices with valid FRU areas are displayed. • Reload Refreshes the display by reading the current FRU entries from the server. • Sort By Sorts the displayed events by event number, time stamp, sensor type and number, event description, or event generator ID.
BB!H:11!vh!.!FO/cppl!!Qbhf!285!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 174 • Appendix B: System management Reload Refreshes the display by reading the SDR data from the server. Updating system firmware and BIOS Using the SSU, you can update the BIOS, update the firmware, and verify the firmware. You can also update the BIOS and firmware without using the SSU. For detailed update instructions, refer to “BIOS updates” on page 189 and to “Firmware updates” on page 190.
BB!H:11!vh!.!FO/cppl!!Qbhf!286!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 175 Data is saved from all sources. There is no way to choose only certain pieces of configuration data to save. You can also restore the information from a saved configuration file. Note: BIOS passwords are stored in the file. Restoring a configuration can change passwords on a server. EMP and LAN passwords are not stored in the file. To save the system configuration 1 From the SSU Main window, choose Config Save/Restore.
BB!H:11!vh!.!FO/cppl!!Qbhf!287!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 176 Appendix B: System management To set up paging alerts To set up the server to send alerts as telephone pages: 1 Install an external modem on the Emergency Management Port (COM2). 2 From the SSU Main window, choose Platform Event Manager (PEM). 3 In the PEM window, click Configure EMP. 4 In the corresponding boxes, enter the following command strings for the modem attached to the EMP port: • ESC Sequence The escape sequence.
BB!H:11!vh!.!FO/cppl!!Qbhf!288!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 177 9 In the Blackout Period box, enter the minimum time, in minutes, between successive pages. The valid range is [0 - 255] where 0 disables the blackout period. Setting a blackout period can save you from being flooded with repeat pages. After you receive a PEP page, no additional pages are sent by PEP for the duration of the blackout period.
BB!H:11!vh!.!FO/cppl!!Qbhf!289!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 178 Appendix B: System management To set up LAN alerts To set up the server to send alerts over the LAN: 1 Configure the remote system to receive alerts. For more information, see the documentation for ASMe. 2 From the SSU Main window, choose Platform Event Manager (PEM). 3 In the PEM window, click Configure LAN. 4 Select the Enable LAN Alerts check box.
BB!H:11!vh!.!FO/cppl!!Qbhf!28:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 179 If you want the alert to be broadcast to an entire subnet, enter the IP address for the subnet. 9 From the Options menu, choose Configure Event Actions. 10 In the BMC LAN Alerting Actions window, move the events that you want to generate an alert to the Enabled column and move all other events to the disabled column using the following buttons: • >> Moves all events from the enabled list to the disabled list.
BB!H:11!vh!.!FO/cppl!!Qbhf!291!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 180 Appendix B: System management 2 In the PEM window, click Configure LAN. 3 If you want to require a password for remote access, enter the password in the Enter New Password box and in the Verify New Password box. Passwords can be from 1 to 16 characters long, using any ASCII character in the range [32-126]. To clear the passwords, leave both boxes blank.
BB!H:11!vh!.!FO/cppl!!Qbhf!292!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 181 • Subnet Mask The IP address for the server's subnet. The server uses this to decide if the alert destination is on the same subnet. 7 Click Save to save the changes. 8 Click Close to return to the PEM window. Setting up remote modem or serial access To configure remote modem or serial access: 1 From the SSU Main window, choose Platform Event Manager (PEM). 2 In the PEM window, click Configure EMP.
BB!H:11!vh!.!FO/cppl!!Qbhf!293!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 182 • 7 Disabled Remote systems are not allowed to initiate connections. From the Restricted Mode list, choose either: • Enabled A remote system can initiate a connection, but cannot perform control operations such as power down, reset, or front panel NMI. • Disabled The remote system has full control of the server.
BB!H:11!vh!.!FO/cppl!!Qbhf!294!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 183 FRU/SDR load utility The Field Replacement Unit (FRU) and Sensor Data Record (SDR) load utility is a DOS-based program used to update the server management subsystem's product level FRU and SDR nonvolatile storage.
BB!H:11!vh!.!FO/cppl!!Qbhf!295!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 184 Appendix B: System management • One or more .fru files describing the system's field replaceable units • A .cfg file describing the system configuration • An .sdr file describing the sensors in the system Command line format The basic command line format is: FRUSDR [-?] [-h] [-d {fru, sdr, smb}] [-cfg filename.cfg] [-fru filename.fru] Option Description -? or -h Display usage information.
BB!H:11!vh!.!FO/cppl!!Qbhf!296!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 185 Using a specified CFG file In most cases, you'll use the standard configuration file master.cfg that is supplied with the utility on the System CD and with software updates: FRUSDR -cfg master.
BB!H:11!vh!.!FO/cppl!!Qbhf!297!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 186 Appendix B: System management SCSISelect The Altos G900 system includes an onboard Adaptec® SCSI controller with two SCSI channels (A and B). The host adapter includes an onboard Adaptec® SCSISelect configuration utility that allows you to view and configure the settings of the host adapter and devices in the server.
BB!H:11!vh!.!FO/cppl!!Qbhf!298!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 187 Software updates Your system comes with preinstalled firmware for the system BIOS, baseboard management controller (BMC), and hot-swap controller (HSC). A FRU/SDR load utility is included on the System CD. Updates are available in two forms: • A software update package (SUP) containing all updates (BIOS, BMC, HSC, and FRU/SDR) • Individual files, one for each update To use either form of update, you must create bootable diskettes.
BB!H:11!vh!.!FO/cppl!!Qbhf!299!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 188 4 Appendix B: System management At the DOS prompt, for an unformatted diskette, type: format a:/s or, for an already formatted diskette, type: sys a: 5 Press Enter. Software update packages A Software Update Package (SUP) contains all the necessary files to perform BIOS, BMC, HSC, and FRU/SDR, or other software updates.
BB!H:11!vh!.!FO/cppl!!Qbhf!29:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 189 Individual updates This section gives procedures for performing individual updates of the BIOS, BMC or HSC firmware, and FRU/SDR data. BIOS updates The IFLASH utility is a DOS-based utility used to install BIOS updates. IFLASH.EXE is included with the BIOS update file. To update the BIOS: 1 Download the software update along with any ReadMe, Release Notes, and other files listed on the Web page for the update.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:1!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 190 Appendix B: System management Changing the BIOS language You can use the BIOS update utility to change the language used for text in the BIOS setup user interface: 1 Insert the diskette holding the BIOS update files into the floppy drive and boot the server. 2 Follow the instructions that appear on the screen, choosing to update the language files.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:2!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 191 7 If you are updating the BMC firmware, run the FRU/SDR load utility. For more information on the FRU/SDR load utility, refer to page 183. FRU/SDR updates The Field Replacement Unit (FRU) and Sensor Data Record (SDR) load utility is a DOS-based program used to update the server FRU and SDR configuration. The utility is included with the update file.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:5!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This appendix shows sample sheets for recording information about the system. Procedures for calculating the system’s power consumption is also discussed.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:6!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 195 Equipment log Use the blank equipment log provided here to record information about the system. Some of this information might be required when running the System Setup Utility (SSU). Item System Server board set Processor (speed and cache) Video display Keyboard Mouse Diskette drive A CD-ROM drive (5.25inch peripheral drive 1) 5.25-inch peripheral drive 2 5.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:7!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 196 Appendix C: Equipment log and configuration worksheets Calculating power consumption The total combined wattage for the system configuration must be less than the output of your power supplies. Use the two worksheets in this section to calculate the power used by your system. For current and voltage requirements of add-in boards and peripherals, refer to the vendor documents.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:8!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 197 Power Usage Worksheet 1 Device Current (maximum) voltage level +3.3 V PCI slot 5 PCI slot 6 PCI slot 7 PCI slot 8 1st 3.5-inch hard disk drive 2nd 3.5-inch hard disk drive 3rd 3.5-inch hard disk drive 4th 3.5-inch hard disk drive 5th 3.5-inch hard disk drive 3.5-inch diskette drive CD-ROM drive 2nd 5.
BB!H:11!vh!.!FO/cppl!!Qbhf!2:9!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 198 Appendix C: Equipment log and configuration worksheets Power Usage Worksheet 1 Device Current (maximum) voltage level 3rd 5.25-inch peripheral drive +3.3 V +5 V 5V Standby +12 V -12 V Fans Total Current Calculating the total combined power used by the system 1 From the previous worksheet, enter the total current for each column in the Power Usage Worksheet 2.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!311!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This appendix helps you identify and solve problems that might occur while you are using the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!312!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 201 Troubleshooting The subsequent sections discuss items you will find useful in managing common system problems. Read it before calling a technician if a problem occurs. Solutions to more serious problems require opening up the system. Do not attempt to open the system by yourself. Contact your dealer or an authorized service center for assistance.
BB!H:11!vh!.!FO/cppl!!Qbhf!313!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 202 Appendix D: Troubleshooting • Are hard disk drives properly formatted or configured? • Are all device drivers properly installed? • Are the configuration settings made with the SSU correct? • Is the operating system properly loaded? Refer to the operating system documentation.
BB!H:11!vh!.!FO/cppl!!Qbhf!314!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 203 If problems persist, contact the software vendor's customer service representative. After the system has been running correctly Problems that occur after the system has been running correctly with no hardware or software changes often indicate equipment failure. However, recent changes made to the system, such as hardware or software that has been added or removed, might also be the source of the problems.
BB!H:11!vh!.!FO/cppl!!Qbhf!315!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 204 Appendix D: Troubleshooting Verifying proper operation of key system lights As POST determines the system configuration, it tests for the presence of each mass storage device installed in the system. As POST checks each device, the activity light for that device should turn on briefly.
BB!H:11!vh!.!FO/cppl!!Qbhf!316!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 205 Frequently asked questions (FAQs) This section provides possible solutions for specific problems. Try the solutions in the order given. If you cannot correct the problem, contact your service representative or authorized dealer for assistance.
BB!H:11!vh!.!FO/cppl!!Qbhf!317!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 206 Appendix D: Troubleshooting • Are the video monitor switch settings correct? • Is the video monitor signal cable properly installed? • Is the onboard video controller enabled? • If you are using an add-in video controller board, do the following: 1 Verify that the video controller board is fully seated in the PCI add-in board connector (and verify that the video monitor is plugged in to the active video controller).
BB!H:11!vh!.!FO/cppl!!Qbhf!318!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 207 If the system power LED is on, but the fans are not rotating properly, check the following: • Are any of the fan fault indicators lit? Is so, try replacing the corresponding fan module.
BB!H:11!vh!.!FO/cppl!!Qbhf!319!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 208 Appendix D: Troubleshooting • Are all relevant switches and jumpers on the hard drive and adapter board set correctly? • Is the hard drive properly configured? Note: The front panel hard disk indicators are for SCSI devices. The hard drive activity indicator on the front panel lights when a SCSI device controlled by the onboard SCSI host controller is in use. This indicator does not display CD-ROM activity.
BB!H:11!vh!.!FO/cppl!!Qbhf!31:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 209 The activity indicator doesn't light. • Make sure you've loaded the correct network drivers. • The network might be idle. Try accessing a server. The onboard network interface controller (NIC) stopped working when an add-in adapter was installed. • Make sure the cable is connected to the port from the onboard NIC. • Make sure your PCI BIOS is current. • Make sure the other adapter supports shared interrupts.
BB!H:11!vh!.!FO/cppl!!Qbhf!321!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 210 Appendix D: Troubleshooting • Try a different copy of the software to see if the problem is with the copy you are using. • Make sure all cables are installed correctly. • If other software runs correctly on the system, contact your vendor about the failing software. If the problem persists, contact the software vendor's customer service representative for assistance.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!323!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN This appendix includes tables of codes and error messages that may be encountered when operating the system.
BB!H:11!vh!.!FO/cppl!!Qbhf!324!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 213 Standard BIOS post codes The table below lists the port-80 codes displayed during the boot process. A beep code is a series of individual beeps on the PC speaker, each of equal length. The table describes the error conditions associated with each beep code and the corresponding POST check point code as seen by a port 80h card. For example, if an error occurs at checkpoint 22h, the BIOS issues the beep code 1-3-1-1.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!328!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 217 CP Beeps 96 98 Reason Clear huge ES segment register 1-2 Search for option ROMs.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!32:!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 219 Recovery BIOS POST codes The table below lists the port-80 codes displayed during a recovery boot process.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!332!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 221 BMC beep codes The table below lists the beep codes generated by the BMC.
BB!H:11!vh!.!FO/cppl!!Qbhf!333!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 222 Appendix E: Codes and error messages POST error messages and codes The table below lists POST error codes and their associated messages. The BIOS prompts the user to press a key in case of serious errors. Some of the error messages are preceded by the string "Error" to highlight the fact that these indicate a system that might be malfunctioning. All POST errors and warnings are logged in the system event log.
BB!H:11!vh!.
BB!H:11!vh!.
BB!H:11!vh!.!FO/cppl!!Qbhf!336!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 225 Code Error Message Failure Description 0B92: Internal Use Area of BMC FRU corrupted. SROM storing chassis information failed Available for use except for FRU command and emergency management port function. 0B93: BMC SDR Repository empty. BMC device (chip) failed 0B94: IPMB signal lines do not respond. SMC (Satellite Management Controller) failed Available for use except for the access function to SMC via IPMB.
BB!H:11!vh!.!FO/cppl!!Qbhf!337!!Gsjebz-!Kbovbsz!28-!3114!!8;24!QN 226 Code 8503: Appendix E: Codes and error messages Error Message Failure Description Invalid System Configuration Data System configuration data destroyed System Configuration Data Read Error System configuration data read error Resource Conflict PCI card resource is not mapped correctly.
BB!H:11!vh!.
BB!H:11!vh!.
