Table of Contents Important Safety Instructions....................................................... 3 Federal Communications Commission.......................................... 5 Connecting the Monitor and Swivel Base.................................... 6 Removing the Monitor and Swivel Base...................................... 6 Introduction ................................................................................... 7 Installation ...............................................................
Important Safety Instructions 1. Please read these instructions thoroughly. 2. Please keep this guide for future use. 3. Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol sprays to clean this device. Use a clean dampened cloth in stead. 4. To avoid damaging the device, only use factory-approved accessories. 5. Protect the device against moisture. 6. In order to set up the device, first place it on a stable surface.
f- The device shows obvious signs of a defect. 16. Use only approved original spare parts, or parts in accordance with the original parts, for repairs. The use of incorrect/unauthorized spare parts may cause further damage. 17. Please contact your service center for any questions regarding service and repairs to guarantee the device’s performance and reliability. 18. The power socket must be installed near the equipment to be easily accessible.
Federal Communications Commission ( FCC Statement ) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Connecting the Monitor and Swivel Base 1. Place the monitor with its tube down on a stable surface. 2. Align the four tabs of the swivel base with the slots in the bottom of the monitor. 3. Insert the tabs into the slots of the monitor 4. Now slowly slide the swivel base toward the front of the monitor till you hear the spring lock click into place. Removing the Monitor and Swivel Base If you need to remove the swivel base, push the spring lock and then pull the swivel base away from the monitor.
Introduction Congratulations on your purchase of this new high performance 17” Monitor. Using state-of-the-art electronics, this monitor supports a 1280 x 1024 resolution. The on-screen display allows you to customize the display settings to suit your individual taste. Features 17-inch monitor with a large, viewable screen for comfortable viewing. OSD user controls for easy and accurate adjustment of the screen image. Energy Star compliant for reduced power consumption.
Installation 1. Connect the monitor signal cable 1 to the 15-pin mini D-sub (VGA) on the back of the computer. 2. Connect the power cord to the power connector on the back panel of the monitor, then plug the other end into an electrical outlet that is easily accessible, and close to the monitor. 3. First turn on the power of the computer, then that of the monitor. 4. Adjust the tilt of the swivel base for maximum viewing comfort. The installation of your monitor is now complete.
User Controls 1. Power Switch 2. Power LED Indicator LED color Turns the monitor on 3. Select Button • Launches On -Screen Display • Make sure the select 4. Status Green On Amber Sleep Backward and Forward Buttons • Backward button (left arrow) moves backward through menu options or decreases adjustment levels. functions or adjustments • Exit menus and On-Screen • Forward button (right Display arrow) moves forward through menu options or increases adjustment levels.
OSD Function Description 1. Press the key to display the OSD menu. 2. To select a function, press the highlighted. 3. Press the 4. Use the 5. Press the 6. Select the select the and keys until the desired function is key to choose the function. and keys to increase or decrease the parameter level of the setting. key to save the new setting. icon if you want to exit the OSD function, and then press the key once.
OSD Icon Summary Icon Function Brightness Contrast H. Size H. Position V. Size Function Description Adjusts display brightness Adjusts display contrast Increases and decreases screen width Shifts display image right or left Increase and decrease screen height V. Position Shifts display image up or down Pin. Balance Adjusts each side of Pincushion Pincushion Parallelogram Trapezoid Rotation Color Temp.
Specification Screen Size Dot Pitch (mm) Surface Viewable Image Area 17” CRT 0.28 Non –glare 16.14” (41.0 cm) Input Signal Video Sync. RGB Analog 0.7Vp-p/75 Ohm a. Separate H/V,TTL(+/-) b. Composite H+V,TTL(+/-) Scanning Frequency Horizontal (KHz) Vertical (Hz) Max. Resolution 30-70 50-160 1280 x 1024 Signal Cable 15-pin mini D-sub Power Consumption Power Supply Max.
Troubleshooting Please refer to the following solutions for the failure symptoms that occur the most frequent. If the symptom remains after trying these suggested solutions, please contact your local authorized service center. Problem: Power LED is not lit when monitor is powered on. Check to make sure that the power cord is connected properly. Make sure that the extension cord or the surge protector is turned on if the monitor is plugged into a power extension cord or a surge protector.