ICONIA Tab A100/A101 SERVICE GUIDE
Revision History Refer to the table below for the updates made to this service guide. Date Chapter Updates Service guide files and updates are available on the ACER/CSD Website. For more information, go to http://csd.acer.com.tw. The information in this guide is subject to change without notice. Copyright Copyright © 2011 by Acer Incorporated. All rights reserved.
Conventions The following conventions are used in this manual: ! WARNING: Indicates a potential for personal injury. ! CAUTION: Indicates a potential loss of data or damage to equipment. + IMPORTANT: Indicates information that is important to know for the proper completion of a procedure, choice of an option, or completing a task. + IMPORTANT: Follow local regulations for battery and circuit board disposal. Batteries and Circuit Boards >10 cm² have been highlighted with a yellow rectangle.
General Information This service guide provides all technical information relating to the basic configuration for Acer global product offering. To better fit local market requirements and enhance product competitiveness, your regional office may have decided to extend the functionality of a machine (such as add-on cards, modems, or extra memory capabilities). These localized features are not covered in this generic service guide.
CHAPTER 1 Hardware Specifications Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Form Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 LCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Audio Codec and Amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-24 Audio Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Wireless Module 802.11b/g/n . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 VRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-25 USB Port . . . . . . . . . . . . . . . . . . . . . . .
IO Board Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29 IO Board Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30 Microphone Module Removal . . . . . . . . . . . . . . . . . . . . . . . . 3-32 Microphone Module Installation. . . . . . . . . . . . . . . . . . . . . . 3-32 3G Antenna Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33 3G Antenna Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 5 Jumper and Connector Locations Mainboard Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Mainboard Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 CHAPTER 6 Field Replaceable Unit List Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHAPTER 1 Hardware Specifications
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Form Factor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 LCM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Network . . . . . . . . . .
AC Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 System Power Management . . . . . . . . . . . . . . . . . . . . . . . . . . 1-26 Card Reader . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27 System LED Indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-27 System DMA Specification . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4
Hardware Specifications and Configurations Features 0 The following is a summary of the computer’s many features: Form Factor 7" 0 Tablet CPU 0 Tegra GPU 250 Dual cortex A9, 1GHz Ultra Low Power GeForce® GPU Memory 0 RAM: LP DDR2 up to 1GB, POP type, discrete on board eMMC: 8G(default) LCM 0 7" WSVGA LCM (1024*600 CMI and CPT) View angle 70 degree at least at each 4 site LVDS interface Network 2G: 3G 0 GSM/GPRS/EDGE 850MHz / 900MHz / 1800Mhz / 1900Mhz Module Er
Camera 0 Rear camera: 5M Camera with Auto focus (Chicony / Aptina 5140) with flash lights (single LED) Detail spec Focus speed < 0.7 sec at 5 lux with flash lights (single LED) Min exposure time: 1/15 sec 720p H.264 @ 30fps/14Mbps recording VGA H.
Audio 0 Single Dual analog Microphone (Noise / echo cancellation) Speaker: above 1.0W/pcs, chamber size is 1cc around each 3.5mm Audio Jack 4ring (with Mic) Dolby Operation System 0 Gingerbread Dimension and Weight 0 Dimensions 195 (L) x 117 (W) x 13.1 (H) mm Weight WIFI 3G SKU < 410g(target) SKU < 430g(target) Expansion Slot MicroSD 0 memory card up to 32G (SDHC 2.
Others 0 Reset hole Docking support (HDMI, power, audio) Accessories 0 In Box Charger + Plug QSG Optional Earphone Micro SD Card Docking + IR remote Pouch 1-8 Hardware Specifications and Configurations
Notebook Tour 0 Front View 0 3 2 1 4 Figure 1-1. Front View Table 1-1.
Rear View 0 2 1 Figure 1-2. Front View Table 1-2.
Top View 0 3 Figure 1-3. 2 1 Top View Table 1-3.
Left View 0 1 Figure 1-4. 2 3 Left View Table 1-4. Left View # Icon Item 1 Headphones/ Speaker Jack 2 Power/ Resume Button 3 Microphone 1-12 Description Power on machine or resume from sleep mode.
Right View 0 6 1 2 Figure 1-5. 3 5 4 Right View Table 1-5. Right View # Icon Item 1 Reset Button 2 micro-HDMI Port 3 Docking Port 4 micro-USB Connector 5 DC-IN Jack 6 Speakers Hardware Specifications and Configurations Description Micro (Type D) HDMI port.
Bottom View (N/A) Figure 1-6. 0 Bottom View Table 1-6.
Hardware Specifications and Configurations ENE KBC KB930 Android HomeKey Touch-key ENE 3534 SMBUS GND LODRV BTST HIDRV Charger IC BQ24725 nBATDRV nACDRV T20 System input - Figure 1-7. + Adapter in(12V/1.
Specification Tables 0 Computer specifications Item Metric Imperial Dimensions Length 195.0 mm 7.68 inch Width 117 mm 4.61 in Height (front to rear) 13.1mm 0.52in Weight (equipped with optical drive, flash drive, and battery) ~405 g 0.9 lbs Weight (equipped with optical drive, flash drive, and battery) Build-in battery Build-in battery Input power Operating voltage 12.0 V dc @ 1.5 A - 18 W Operating current 1.
System Board Major Chips Item Specification Core logic Tegra 250 Dual cortex A9, 1GHz VGA Integrated with CPU LAN N/A USB 2.
Processor Specifications Item T20 CPU Speed (GHz) Cores/ Threads Bus Speed (FSB/ DMI/QBI) 1 GHz 2 Cores 64 bits Mfg Tech (nm) 40 nm Cache Size 1 MB Package 23x23 FCBGA Voltage 1.0-1.
Memory Combinations (N/A) Slot 1 (MB) Slot 2 (MB) Total Memory (MB) Video Interface (Integrated) Item Specification Chipset Package Interface Compatibility Sampling rate Hardware Specifications and Configurations 1-19
BIOS (N/A) Item Specification BIOS vendor BIOS Version BIOS ROM type BIOS ROM size Features LAN Interface Item Specification LAN Chipset N/A (No LAN Port) LAN connector type N/A (No LAN Port) LAN connector location N/A (No LAN Port) Features UMTS /WCDMA a. 3G dual band / b. 3G qual band / c. LTE n HSDPA up to 7.2Mbps/ HSUPA up to 5.
Hard Disk Drive (AVL components) (N/A) Item Specification Vendor & Model Name Capacity (GB) Bytes per sector Data heads Drive Format Disks Spindle speed (RPM) Performance Specifications Buffer size Interface Fast data transfer rate (Mbits / sec, max) Media data transfer rate (Mbytes/sec max) DC Power Requirements Voltage tolerance Super-Multi Drive (N/A) Item Specification Vendor & Model name Performance Specification Transfer rate (KB/sec) Buffer Memory Interface Applicable disc format Loading mechanis
BD Drive (N/A) Items Specifications Vendor & Model name Performance Specification Transfer rate (KB/sec) Buffer Memory Interface Applicable disc format Loading mechanism Power Requirement Input Voltage LED 7.1” Item Specification Vendor/Model name CMI/AT070TNA2 Screen Diagonal (mm) 255.52 mm Active Area (mm) 222.72 mm x 125.28 mm Display resolution (pixels) 1024 x 3(RGB) x 600 Pixel Pitch (mm) 0.2175mm × 0.
LCD Inverter (N/A) Item Specification Vendor & Model name Brightness conditions Input voltage (v) Input current (mA) Output voltage (V, RMS) Output current (mA, RMS) Output voltage frequency (KHz) Display Supported Resolution (LCD) Resolution 16 bits 32 bits Intel NVIDIA ATI X X X V X 1024x 3(RGB) x 600 Graphics Controller (N/A) Item Specification VGA Chip Supports Display Supported Resolution (GPU) Resolution 16 bits 32 bits Intel NVDIA ATI X X X V X 1024x 3(RGB) x 600 Bluetooth I
Bluetooth Module Item Controller Specifications Azurewave AW-NH611 - Broadcom BCM4329 SoC Features Fully support BT 2.
Audio Interface Item Specification Audio Controller Wolfson WM8903 Audio onboard or optional On board Mono or Stereo Stereo Resolution Support 24bit Compatibility I2S audio Interface Sampling rate Sample rate up to 44.1KHz Internal microphone Yes Internal speaker/quantity Yes/(1W speakers x2) Wireless Module 802.11b/g/n Item Chipset Specification Azurewave AW-NH611 - Broadcom BCM4329 SoC Data throughput 802.11b/g: 11~54 Mbps 802.11n: MCS 0-7 Protocol IEEE 802.
USB Port Item Specification USB compliance level USB2.0 Protocol EHCI Number of USB port(s) 1 Location one at the right side Output Current HDMI Port Item Specification Compliance level HDMI1.3a Data throughput Up to 16.7 million colors Number of HDMI port(s) 1 Location one at the right side AC Adapter Item Specification Input rating 18W Maximum input AC current 0.5A(RMS) at 100Vac Inrush current 60A Max. @230Vac Efficiency Refer to EPS 2.
Card Reader Item Specification Chipset Embedded in T20 SOC.
System Interrupt Specification (N/A) Hardware IRQ System Function IRQ0 IRQ1 IRQ2 IRQ3 IRQ5* IRQ6 IRQ7* IRQ8 IRQ9* IRQ10* IRQ11 IRQ12 IRQ13 IRQ14 IRQ15 *Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none. NOTE: ExpressCards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15.
System IO Address Map I/O address (hex) System function (shipping configuration) 000 - 00F DMA controller no. 1 010 - 01F Unused 020 - 021 Interrupt controller no.
System I/O Address Specifications I/O address (hex) System function (shipping configuration) 220 - 22F Entertainment audio 230 - 26D Unused 26E - 26 Unused 278 - 27F Unused 280 - 2AB Unused 2A0 - 2A7 Unused 2A8 - 2E7 Unused 2E8 - 2EF Reserved serial port 2F0 - 2F7 Unused 2F8 - 2FF Infrared port 300 - 31F Unused 320 - 36F Unused 370 - 377 Secondary diskette drive controller 378 - 37F Parallel port (LPT1/default) 380 - 387 Unused 388 - 38B FM synthesizer-OPL3 38C - 3AF Unuse
CHAPTER 2 Diagnostic Utilities
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Diagnostic Tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 NGA EUU Installation Procedure. . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Picasso Diagnostic Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Utilities Introduction 0 The ICONIA Tab A100/A101 has a set of software tools designed to diagnose problems with its hardware components. Diagnostic Tools 0 To access the diagnostic tools utility guide, click here. NGA EUU Installation Procedure NOTE: 0 NOTE: Before installing EEU software, make sure ICONIA tablet is not connected to a computer. 1. Install EUU software on a PC. When the following dialog is shown, click OK to continue. Figure 2-1. Starting Installation 2.
3. Install USB driver. (Figure 2-3) Figure 2-3. USB Driver Installation 4. To enable USB debugging, on the device, go to the Settings/Applications/Development menu and click the USB debugging checkbox. (Figure 2-4.) Figure 2-4.
5. Follow the instructions shown in Figure 2-5 to find OS image version. Figure 2-5. Finding OS Image Version 6. If image version is not available, follow instructions in Figure 2-6 to manually reset device. When procedure is complete, go to Step 1 of this procedure. Figure 2-6.
7. If image version is available, current and new version information is shown. Click Next to continue. (Figure 2-7) Figure 2-7. Image Versions 8. Enter CPU ID of device. Click Next to continue. (Figure 2-8) NOTE: NOTE: Maximum number of characters for ID is sixteen (16). Figure 2-8.
9. Upgrade process begins as shown in Figure 2-9 + IMPORTANT: Upgrade process will not complete if USB cable is unplugged. Figure 2-9. Upgrade Process 10. If upgrade process is successful, Figure 2-10 is shown. If an upgrade error is shown, go to step 12, If a CPU ID value error is identified, go to step 19. Figure 2-10. Upgrade Process Success 11. Click Finish to exit.
12. If CPU ID is correct but upgrade process is not successful, Figure 2-11 is shown. Figure 2-11. Upgrade Process Failure 13. Click Retry to start upgrade process. Go to Step 8. 14. Click Exit to cancel upgrade process. 15. If upgrade process is cancelled, a confirmation dialog is shown. (Figure 2-12) Figure 2-12. Upgrade Process Cancellation Confirmation Dialog 16. Click No to return to Retry dialog in Step 12. 17. Click Yes to confirm cancellation.
18. Click OK to exit the program. (Figure 2-13) Figure 2-13. Final Cancellation Dialog 19. If CPU ID value is not correct, Figure 2-14 is shown. Upgrade process failed because wrong CPU ID value was entered. Follow instructions for recovery. Figure 2-14. Wrong CPU ID 20. Click Retry to start upgrade process. Go to Step 8. 21. Click Exit to cancel upgrade process.
22. If upgrade process is cancelled, a confirmation dialog is shown. (Figure 2-15) Figure 2-15. Upgrade Process Cancellation Confirmation Dialog 23. Click No to return to Retry dialog in Step 19. 24. Click Yes to confirm cancellation. 25. Click OK to exit program. (Figure 2-16) Figure 2-16.
Picasso Diagnostic Tool Diagnostic Utilities 0 2-11
2-12 Diagnostic Utilities
CHAPTER 3 Maintenance Procedures
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Recommended Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Maintenance Flowchart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 SIM/Micro-SD Card Removal . . . . . . . . . . . . .
Machine Maintenance Procedures Introduction 0 This chapter contains general information about the notebook, a list of tools needed to perform the required maintenance and step by step procedures on how to remove and install components from the notebook computer. General Information 0 The product previews seen in the following procedures may not represent the final product color or configuration. Cable paths and positioning may also differ from the actual model.
Maintenance Flowchart 0 The flowchart in Figure 3-1 provides a graphic representation of the module removal and installation sequences. It provides information on what components need to be removed and installed during servicing. Figure 3-1.
Getting Started 0 The flowchart (Figure 3-1) identifies sections illustrating the entire removal and install sequence. Observe the order of the sequence to avoid damage to any of the hardware components. Perform the following prior to performing any maintenance procedures: 1. Place system on a flat work surface. 2. Make sure device is powered up. 3. Disconnect AC Adapter (A) and remove all cables from system and peripherals. (Figure 3-2) . A B Figure 3-2. Device Overview with Power Button 4.
SIM/Micro-SD Card Removal NOTE: 0 NOTE: SIM/Micro-SD card not available in non-3G SKU 1. Open SIM/Micro-SD card cover. (Figure 3-4) A Figure 3-4. SIM/micro-SD Card Removal 2. Press in SIM card (B) to unlock and remove from spring locking mechanism. (Figure 3-5) B Figure 3-5.
C Figure 3-6. micro-SD Card (non-3G SKU) 3. Press in Micro-SD card (C) to unlock and remove from spring locking mechanism. (Figure 3-5 and Figure 3-6) 4. Secure SIM/Micro-SD card cover. SIM/Micro-SD Card Installation 0 1. Open SIM/Micro-SD card cover (A). (Figure 3-4) 2. Install and press in to secure SIM card (B). (Figure 3-5) 3. Install and and press in to secure Micro-SD card (C). 4. Close and secure SIM/Micro-SD card cover.
Lower Case Removal 0 Prerequisite: SIM/Micro-SD Card Removal 1. Starting from top of device, release top cover. (Figure 3-7 and Figure 3-8) 3-8 Figure 3-7. Releasing Top Cover (1 of 2) Figure 3-8.
2. Rotate the device and continue to remove all the covers from the right, bottom and left sides of the bezel. (Figure 3-9 through Figure 3-14) Figure 3-9. Releasing Right Cover (1 of 2) Figure 3-10.
Figure 3-11. Releasing Bottom Cover (1 of 2) Figure 3-12.
Figure 3-13. Releasing Left Cover (1 of 2) Figure 3-14.
3. Remove screws (A) from top and bottom of bezel. (Figure 3-15 and Figure 3-16) A Figure 3-15. Bezel Screws (1 of 2) A Figure 3-16.
4. Grasp lower case and bezel as shown in Figure 3-17. Figure 3-17. Removing Lower Case (1 of 3) 5. Separate lower case from bezel locking latches. (Figure 3-18) Figure 3-18.
6. Remove lower case from bezel. (Figure 3-19) Figure 3-19.
Lower Case Installation 0 1. Install and secure lower case locking latches (not shown) on bezel. 2. Install and secure screws (A) on bezel. (Figure 3-15 and Figure 3-16) 3. Install and secure top, right, bottom and left side covers to bezel. (Figure 3-9 through Figure 3-14) ID A Machine Maintenance Procedures Size M2.0x3.
Battery Removal 0 Prerequisite: Lower Case Removal 1. Locate battery (A) on shield case. (Figure 3-20) A Figure 3-20. Battery 2. Disconnect battery cable (B) from mainboard connector (C). (Figure 3-21) B C Figure 3-21.
3. Remove screws (D) from shielding case. (Figure 3-22 and Figure 3-23) D Figure 3-22. Battery Screws (1 of 2) D Figure 3-23.
NOTE: NOTE: Make sure antenna and GPS cables (E) are clear of battery before removal E Figure 3-24. GPS and Antenna Cables 4. Remove battery from shield case. Battery Installation 0 1. Install battery (A) on shielding case. (Figure 3-20) NOTE: NOTE: Place cables (E) between battery and 3G module. (Figure 3-24) 2. Install and secure screws (D) to shielding case. (Figure 3-22 and Figure 3-23) 3. Connect battery cable (B) to mainboard connector (C). (Figure 3-21) 4. Install lower case.
3G Module Removal 0 Prerequisite: Battery Removal 1. Locate 3G module (A) on LCD support plate. (Figure 3-25) A Figure 3-25. 3G Module Overview 2. Disconnect GPS (C) and RF (B) cables from 3G module connectors labeled aux and main. (Figure 3-26) B C D Figure 3-26. 3G, RF and WLAN Cables 3. Disconnect WLAN main (D) cable from mainboard connector.
4. Remove screw (E) from shielding case. a A E Figure 3-27. 3G Module, Mainboard Connector and 3G Screw 5. Remove 3G module (A) from mainboard connector (a). 6. Disconnect RF cable (F) from IO board connector. (Figure 3-28) F Figure 3-28. RF Cable 7. Remove RF cable (F).
3G Module Installation 0 1. Connect RF cable (F) to IO board connector. (Figure 3-28) 2. Install 3G module (A) on mainboard. (Figure 3-27) 3. Install and secure screw (E) to mainboard. ! CAUTION: Route the WLAN antenna around the IO board FPC to prevent it from being disconnected from mainboard. 4. Connect WLAN antenna (D) to mainboard connector. (Figure 3-26) 5. Connect GPS (C) and RF (B) cables to 3G module connectors labeled auxiliary and main. 6. Install battery.
DC-In Cable Removal 0 Prerequisite: Battery Removal 1. Locate DC-IN cable (A) on bezel. (Figure 3-29) A Figure 3-29. DC-IN Cable Overview 2. Disconnect DC-IN cable (A) from mainboard connector (B). (Figure 3-30) B C A Figure 3-30. DC-IN Cable, Jack and Mainboard Connector 3. Remove DC-IN cable jack (C) from bezel guide. 4. Remove DC-IN cable.
DC-In Cable Installation 0 1. Install and secure DC-IN jack on bezel. (Figure 3-30) 2. Connect DC-In cable (A) to mainboard connector (B). 3. Install lower case.
Speaker Module Removal 0 Prerequisite: Battery Removal 1. Locate speaker modules (A) on bezel. (Figure 3-31) A Figure 3-31. Speaker Modules Overview 2. Disconnect Home key FFC (B) from mainboard connector (C). (Figure 3-32) B C Figure 3-32.
3. Disconnect speaker cable (D) from mainboard connector (E). (Figure 3-33) D E Figure 3-33. Speaker Modules Overview 4. Remove screws (F) from LCD support plate. (Figure 3-34 and Figure 3-35) F Figure 3-34.
F Figure 3-35. Speaker Module Screws (2 of 2) 5. Remove speakers from bezel. Speakers Installation 0 1. Install speakers (A) on bezel. (Figure 3-31) 2. Install and secure screws (F) to support plate. (Figure 3-34 and Figure 3-35) 3. Connect speaker cable (D) to mainboard connector (E). (Figure 3-33) 4. Connect home key FFC (B) to mainboard connector (C). (Figure 3-32) 5. Install battery. ID F 3-26 Size Quantity M2.0x4.
IO Board FPC Removal 0 Prerequisite: Battery Removal (non-3G SKU) 3G Module Removal (3G SKU) 1. Locate IO Board FPC (A). (Figure 3-36) A Figure 3-36. IO Board FPC Overview 2. Remove adhesive tape (B) securing FPC to support plate. (Figure 3-37) B A C D Figure 3-37. IO Board FPC and Mainboard Connectors 3. Disconnect FPC (A) from mainboard connector (C). 4. Disconnect FPC (A) from IO board connector (D). 5. Remove FPC.
IO Board FPC Installation 0 1. Connect FPC (A) to mainboard connector (C). (Figure 3-37) 2. Connect FPC (A) to IO board connector (D). 3. Install tape (B) on FPC and secure to support plate. 4. Install battery. (non-3G SKU) 5. Install 3G module.
IO Board Removal 0 Prerequisite: IO Board FPC Removal 1. Locate IO Board (A). (Figure 3-38) A Figure 3-38. IO Board Overview 2. Disconnect 3G antenna cable (B) from IO board connector. (Figure 3-39) G D E C F B Figure 3-39. IO Board Cables and Screw 3. Disconnect microphone cable (C) from IO board connector (D). 4. Disconnect light sensor cable (E) from IO board connector (F). 5. Remove screw (G) from bezel. 6. Remove board from bezel.
7. Disconnect RF cable from IO board connector (H). H Figure 3-40. IO Board and RF Cable IO Board Installation 0 1. Connect RF cable (H) to IO board connector. (Figure 3-40) NOTE: NOTE: Light sensor must be secured in support plate guide. Microphone cable must be under IO board. 2. Align IO board with bezel guides (J). (Figure 3-41) NOTE: NOTE: RF cable must be secured under IO board guides (K). K J J Figure 3-41. IO Board and Bezel Guides 3. Install board on bezel.
4. Install and secure screw (G) to bezel. (Figure 3-39) 5. Connect light sensor cable (E) to IO board connector (F). 6. Connect microphone cable (C) to IO board connector (D). 7. Connect 3G antenna cable (B) to IO board connector. 8. Install IO Board FPC. ID G Machine Maintenance Procedures Size M2.0x3.
Microphone Module Removal 0 Prerequisite: IO Board Removal 1. Locate microphone module (A).(Figure 3-42) A Figure 3-42. Microphone Module Overview 2. Remove microphone (A) from bezel guides. Microphone Module Installation 0 1. Install and secure microphone (A) in bezel guide (B) facing out. (Figure 3-43) A B Figure 3-43. Installing Microphone Module in Bezel Guide 2. Install IO Board.
3G Antenna Removal 0 Prerequisite: IO Board Removal 1. Locate 3G Antenna (A). (Figure 3-44) A B Figure 3-44. 3G Antenna Overview 2. Release 3G antenna foil (B) secured to support plate. 3. Remove 3G antenna from bezel. 3G Antenna Installation 0 1. Install 3G antenna (A) on bezel. (Figure 3-44) 2. Secure 3G antenna foil (B) on support plate. 3. Install IO Board.
Light Sensor Module Removal 0 Prerequisite: IO Board Removal 1. Locate light sensor module (A). (Figure 3-45) A Figure 3-45. Light Sensor Module Overview 2. Remove light sensor module (A) from bezel. Light Sensor Module Installation 0 1. Install and secure light sensor module (A, Figure 3-45) in clips in bezel guides (B). (Figure 3-46) B B Figure 3-46. Light Sensor Module Bezel Guides 2. Install IO Board.
GPS Antenna Removal 0 Prerequisite: 3G Module Removal (3G SKU) Speaker Module Removal (non-3G SKU) 1. Locate GPS Antenna (A). (Figure 3-47) B A Figure 3-47. GPS Antenna Overview 2. Release GPS antenna foil (B) secured to support plate. 3. Remove GPS antenna (A) from bezel. GPS Antenna Installation 0 1. Install GPS antenna (A) on bezel. (Figure 3-47) 2. Secure GPS antenna foil (B) on support plate. 3. Install 3G module. (3G SKU) 4. Install speaker modules.
Mainboard Removal 0 Prerequisite: Speaker Module Removal IO Board FPC Removal 1. Locate mainboard (A). (Figure 3-48) A Figure 3-48. Mainboard Overview 2. Disconnect LVDS cable (B) from mainboard connector (C). (Figure 3-49) B C D Figure 3-49. LVDS Cable and Mainboard Connector 3. Remove tape (D) securing touch screen FPC to mainboard.
4. Disconnect touch screen FPC (E) from mainboard connector (F). (Figure 3-50) E F Figure 3-50. Touch Screen FPC and Mainboard Connector 5. Remove screws (G) from bezel. (Figure 3-51 through Figure 3-53) G G Figure 3-51.
G Figure 3-52. Mainboard Screws (2 of 3) G Figure 3-53. Mainboard Screws (3 of 3) 6. Remove mainboard from support plate.
Mainboard Installation 0 1. Install mainboard (A) on support plate. (Figure 3-48) 2. Install and secure screws (G) to bezel. (Figure 3-51 through Figure 3-53) 3. Connect touch screen FPC (E) to mainboard connector (F). (Figure 3-50) 4. Install tape (D) securing touch screen to mainboard. (Figure 3-49) 5. Connect LVDS cable (B) to mainboard connector (C). 6. Install speaker modules. 7. Install IO Board FPC. ID G Machine Maintenance Procedures Size M2.0x3.
Rear CCD Board Removal 0 Prerequisite: Mainboard Removal 1. Place bottom of mainboard on a flat surface.(Figure 3-54) A Figure 3-54. Mainboard Overview 2. Locate rear CCD board (A). 3. Remove screws (B) from CCD to mainboard. (Figure 3-55) B B Figure 3-55.
4. Disconnect and remove rear CCD board (A) from mainboard connector (C). (Figure 3-56 and Figure 3-57) C A Figure 3-56. Removing Rear CCD Board (1 of 2) Figure 3-57.
Rear CCD Board Installation 0 1. Connect CCD board (A) to mainboard connector (C). (Figure 3-58) A C Figure 3-58. Installing Rear CCD Board (1 of 2) Figure 3-59. Installing Rear CCD Board (2 of 2) 2. Install and secure screws (B) to mainboard. (Figure 3-55) 3. Install mainboard. ID B 3-42 Size M2.0x3.
WLAN Antenna Removal 0 Prerequisite: Mainboard Removal 1. Locate WLAN antenna (A). (Figure 3-60) B A Figure 3-60. WLAN Antenna Overview 2. Release WLAN antenna foil (B) secured to support plate. 3. Remove WLAN antenna (A) from bezel. WLAN Antenna Installation 0 1. Install WLAN antenna (A) on bezel. (Figure 3-60) 2. Secure WLAN antenna foil (B) on support plate. 3. Install mainboard.
Home Key Board Removal 0 Prerequisite: Mainboard Removal 1. Locate home key board (A). (Figure 3-61) A Figure 3-61. Home Key Board Overview 2. Remove home key board (A) from bezel. 3. Disconnect home key FFC (B) from board connector (C). (Figure 3-62) B C Figure 3-62.
Home Key Board Installation 0 1. Connect home key FFC (B) to board connector (C). (Figure 3-62) 2. Align home key board with bezel guide (D). (Figure 3-63) D Figure 3-63. Home Key Board Bezel Guide 3. Install and secure home key board (A) to bezel. (Figure 3-61) 4. Install mainboard.
3-46 Machine Maintenance Procedures
CHAPTER 4 Troubleshooting
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Power On Issues . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 No Display Issues. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 LCD Picture Failure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Touch Screen Failure . . . . . . . . . . . . . . .
Troubleshooting Introduction 0 This chapter contains information about troubleshooting common problems associated with the notebook. General Information 0 The following procedures are a guide for troubleshooting computer problems. The step by step procedures are designed to be performed as described. NOTE: NOTE: The diagnostic tests are intended for Acer products only. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1.
Power On Issues 0 If the system fails, perform the following: Start Check AC cable / BATT only power on OK NG Swap AC cable/ BATT OK Swap M/B Figure 4-1.
No Display Issues 0 If the display fails, perform the following: Start OK NG Can power on Go to no power Trouble shoo ng step OK NG Check LCD cable swap LCD cable OK LCD panel NG Swap LCD panel OK Swap M/B Figure 4-2.
LCD Picture Failure 0 If the LCD picture fails, perform the following: Start OK NG Check LCD cable Swap LCD cable OK Check LCD panel NG Swap LCD panel OK Swap M/B Figure 4-3.
Touch Screen Failure 0 If the touch screen fails, perform the following: Start OK NG Check touch screen cable Swap touch screen cable OK NG Check touch screen small/B Swap touch screen small/B OK Check touch screen panel NG Swap touch screen panel OK Swap M/B Figure 4-4.
Internal Speaker Failure 0 If the internal speakers fail, perform the following: Start OK Check SPK NG Swap SPK OK Swap M/B Figure 4-5.
Internal Microphone Failure 0 If the internal microphone fails, perform the following: Start OK Check the front MIC and the back MIC OK Swap the front MIC NG OK Check the front MIC OK Swap M/B Figure 4-6.
USB Failure/mini-USB Failure 0 If the USB fails, perform the following: Start OK NG Check the USB/B to M/B FFC Swap the USB/B to M/B FFC OK Check the USB/B NG Swap the USB/B OK Swap M/B Figure 4-7.
Front Camera Failure 0 If the front camera fails, perform the following: Start OK Check the front camera NG Swap the front camera OK Swap M/B Figure 4-8.
Back Camera Failure 0 If the back camera fails, perform the following: Start OK Check the back camera NG Swap the back camera OK Swap M/B Figure 4-9.
P-Sensor Failure 0 If the P-sensor fails, perform the following: Start OK NG Check conduc ve co on on the Lower Add conduc ve co on OK Check related Mylar on the MB NG Add related Mylar OK Swap M/B Figure 4-10.
3G Function Failure 0 If the 3G function fails, perform the following: Start OK NG Check the 3G antenna Swap the 3G Main antenna OK Check the 3G card NG Swap the 3G card OK Swap M/B Figure 4-11.
Wireless Function Test Failure 0 If the wireless function fails, perform the following: Start OK Check the W/L antenna NG Swap the antenna OK Swap M/B Figure 4-12.
GPS Function Test Failure (Wi-Fi SKU) 0 If the GPS function (Wi-Fi SKU) test fails, perform the following: Start OK Check the GPS antenna NG Swap the antenna OK Swap M/B Figure 4-13.
GPS Function Test Failure (3G SKU) 0 If the GPS function test (3G SKU) fails, perform the following: Start OK NG Check the 3G Aux antenna Swap the 3G Aux antenna OK Check the 3G card NG Swap the 3G card OK Swap M/B Figure 4-14.
Docking Station Test Failure 0 If the docking station test fails, perform the following: Start OK NG Check the Docking/B to M/B FFC Swap the Docking/B to M/B FFC OK Check the Docking/B NG Swap the Docking/B OK Swap M/B Figure 4-15.
Other Functions Failure 0 1. Check component connection to mainboard. 2. To test for mainboard fault, swap mainboard.
4-20 Troubleshooting
CHAPTER 5 Jumper and Connector Locations
Mainboard Top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Mainboard Bottom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumper and Connector Locations Mainboard Top 0 JP10 JP67 JP2 JP70 U129 JP12 JMIN2 U1 JHDMI1 SW6 Figure 5-1. Mainboard Top Table 5-1.
Mainboard Bottom ANT3 0 JP5 ANT5 PJP1 U19 JP73 JP58 JMIN2 JLVDS3 JP55 PJP2 Figure 5-2. Mainboard Bottom Table 5-2.
CHAPTER 6 Field Replaceable Unit List
Exploded Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6 Screw List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU List This chapter provides users with a FRU (Field Replaceable Unit) listing in global configurations for the ICONIA Tab A100/A101. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). NOTE: NOTE: When ordering FRU parts, check the most up-to-date information available on the regional web or channel. Part number changes will not be noted on the printed Service Guide.
Exploded Diagrams 0 Main Assembly 0 16 15 14 1 2 13 3 12 4 5 11 10 6 7 9 8 Figure 6-1.
Table 6-1. Main Assembly Exploded Diagram No. Description P/N 1 ANTENNA - WLAN 50.H6S02.004 2 ANTENNA - GPS 50.H6S02.005 3 HOME KEY BOARD 55.H6S02.003 4 CAMERA BOARD INCL. 5M CAMERA 55.H6S02.001 5 MAINBOARD MB.H6R00.001 6 SPEAKER L+R 23.H6S02.002 7 TOP STRIP COVER 60.H6W02.001 8 RIGHT STRIP COVER 60.H6S02.005 9 BOTTOM STRIP COVER 60.H6S02.003 10 LOWER CASE IMR INCL. CAMERA LENS 60.H6S02.001 11 FFC FOR IO BOARD 50.H6S02.002 12 IO BOARD 55.H6S02.002 13 MIC SET 23.
FRU List 0 Table 6-2. FRU List Category Description P/N ADAPTER Adapter PHIHONG 18W 12V/1.5A Black PSA18R-120P(AI)-R LF AP.0180P.002 Adapter PHIHONG 18W 12V/1.5A 1.1x3.0x7.5 Black PSA18R-120P(AI)-R, w/i 150cm cable LF AP.0180P.003 Battery SANYO BAT-711 Prismatic 2S1P SANYO 2 Cell 1530mAh Main COMMON BT.00203.005 CAMERA BOARD INCL. 5M CAMERA - FOR WIFI 55.H6S02.001 CAMERA BOARD INCL. 5M CAMERA - FOR 3G 55.H6V02.001 IO BOARD FOR 3G 55.H6S02.002 IO BOARD FOR WIFI 55.H6S02.
Table 6-2. FRU List (Continued) Category Description P/N FFC FOR IO BOARD 50.H6S02.002 FFC FOR HOME KEY BOARD 50.H6S02.003 EXTERNAL USB CABLE XZ.70200.115 EXTERNAL HDMI CABLE XZ.70200.117 AC CLIP 18W -EU 27.L0302.001 AC CLIP 18W -US 27.L0302.002 AC CLIP 18W -CN 27.L0302.003 AC CLIP 18W -UK 27.H6002.001 AC CLIP 18W -AU 27.H6002.002 AC CLIP 18W -ARG 27.H6002.003 AC CLIP 18W -BRZ 27.H6002.004 CASE/COVER/BRACKET ASSEMBLY LOWER CASE IMR INCL. CAMERA LENS 60.H6S02.
Table 6-2. FRU List (Continued) Category Description P/N ANTENNA - GPS FOR 3G 50.H6S02.005 ANTENNA - GPS FOR WIFI 50.H6S02.006 ANTENNA - 3G EU 50.H6W02.002 ANTENNA - 3G US 50.H6V02.001 CAMERA 2M 57.H6S02.001 Mainboard A100_8u Nvidia Tegra 250 Rev 1.0, W/WIFI&CPU&RAM MB.H6R00.001 Mainboard A100_16u Nvidia Tegra 250 Rev 1.0, W/WIFI&CPU&RAM MB.H6S00.001 MIC SET 23.H6S02.001 SPEAKER L+R 23.H6S02.
Screw List 0 Table 6-3. Screw List Category Description P/N SCREW FRU List SCREW 2D 2.5L K 4.05D NI NL 86.H6S02.001 SCREW 2D 4.0L K 4.0D NI NL 0.3T 86.H6S02.002 SCREW 2.0D 3.0L K 3.6 ZK NL+CR3+ 86.H6S02.
6-10 FRU List
CHAPTER 7 Model Definition and Configuration
A100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 A101 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Model Definition and Configuration A100 0 Table 7-1. BOM Name, RO & NS Model Country P/N BOM Name RO NS A100 AU/NZ XE.H6RAN.001 A100_8u AAP ACA A100 AU/NZ XE.H6SAN.001 A100_16u AAP ACA A100 BE XE.H6REN.005 A100_8u EMEA ACH A100 BE XE.H6SEN.001 A100_16u EMEA ACH A100 CA XE.H6RPN.004 A100_8u PA AAC A100 CA XE.H6SPN.001 A100_16u PA AAC A100 ES XE.H6RPN.005 A100_8u PA AAC A100 ES XE.H6SPN.002 A100_16u PA AAC A100 Eastern Europe XE.H6REN.
Table 7-1. BOM Name, RO & NS (Continued) Model 7-4 Country P/N BOM Name RO NS A100 MY XE.H6RAN.004 A100_8u AAP ASSSB A100 MY XE.H6SAN.004 A100_16u AAP ASSSB A100 Nordic XE.H6REN.013 A100_8u EMEA EMEA A100 Nordic XE.H6SEN.012 A100_16u EMEA EMEA A100 PH XE.H6RAN.006 A100_8u AAP APHI A100 PH XE.H6SAN.005 A100_16u AAP APHI A100 PL XE.H6REN.012 A100_8u EMEA ASK A100 PL XE.H6SEN.010 A100_16u EMEA ASK A100 RU XE.H6REN.007 A100_8u EMEA ACR A100 RU XE.
Table 7-1. BOM Name, RO & NS (Continued) Model Country P/N BOM Name RO NS A100 West EU-1 XE.H6SEN.008 A100_16u EMEA EMEA A100 West EU-1 XE.H6SEN.009 A100_16u EMEA EMEA A100 ZA XE.H6REN.008 A100_8u EMEA AAF A100 ZA XE.H6SEN.007 A100_16u EMEA AAF Table 7-2. Description & Mobile Device Model Country P/N Description Mobile Device A100 AU/NZ XE.H6RAN.001 A100 Tablet None AAP_GEN4 AndroidAU-Tab-1 AU- Blue Wi-Fi only N N Tablet A100 AU/NZ XE.H6SAN.
Table 7-2. Description & Mobile Device (Continued) Model 7-6 Country P/N Description Mobile Device A100 GCTWN XE.H6STN.001 A100 Tablet None AAP_GEN4TW AndroidTW-Tab-1 US- Blue Wi-Fi only_16G N N Tablet A100 HK XE.H6RCN.001 A100 Tablet None AAP_GEN4TW AndroidHK-Tab-1 UK- Blue Wi-Fi only N N Tablet A100 HK XE.H6SCN.001 A100 Tablet None AAP_GEN4TW AndroidHK-Tab-1 UK- Blue Wi-Fi only_16G N N Tablet A100 ID XE.H6RAN.
Table 7-2. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A100 MOYO XE.H6REN.010 A100 Tablet None EMEA_GEN5 AndroidME-6 EU- Blue Wi-Fi only N N Tablet A100 MOYO XE.H6SEN.013 A100 Tablet None EMEA_GEN5 AndroidME-6 EU- Blue Wi-Fi only_16G N N Tablet A100 MX XE.H6RPN.003 A100 Tablet EMEA_GEN3 AndroidMexico-Tab-1 US- Blue Wi-Fi only N N Tablet A100 MX XE.H6SPN.
Table 7-2. Description & Mobile Device (Continued) Model 7-8 Country P/N Description Mobile Device A100 SG XE.H6RAN.007 A100 Tablet None AAP_GEN4 AndroidSG-Tab-1 UK- Blue Wi-Fi only N N Tablet A100 SG XE.H6SAN.006 A100 Tablet None AAP_GEN4 AndroidSG-Tab-1 UK- Blue Wi-Fi only_16G N N Tablet A100 TH XE.H6RAN.008 A100 Tablet None AAP_GEN4 AndroidTH-Tab-1 EU- Blue Wi-Fi only N N Tablet A100 TH XE.H6SAN.
Table 7-2. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A100 WW S7.H6RWN.001 A100 Sample None Bar-type WiFi 7.0 WSVGA Blue AU plug N N Tablet A100 WW S7.H6RWN.002 A100 Sample None Bar-type WiFi 7.0 WSVGA Blue EU plug N N Tablet A100 WW S7.H6RWN.003 A100 Sample None Bar-type WiFi 7.0 WSVGA Blue CN plug NN Tablet A100 WW S7.H6RWN.004 A100 Sample None Bar-type WiFi 7.0 WSVGA Blue UK plug N N Tablet A100 WW S7.H6RWN.
Table 7-3. CPU, Memory 1 & Band Model Country P/N CPU Memory1 Band A100 AU/NZ XE.H6RAN.001 NV-TEGRA250 eMMC8GB None A100 AU/NZ XE.H6SAN.001 NV-TEGRA250 eMMC16GB None A100 BE XE.H6REN.005 NV-TEGRA250 eMMC8GB None A100 BE XE.H6SEN.001 NV-TEGRA250 eMMC16GB None A100 CA XE.H6RPN.004 NV-TEGRA250 eMMC8GB None A100 CA XE.H6SPN.001 NV-TEGRA250 eMMC16GB None A100 ES XE.H6RPN.005 NV-TEGRA250 eMMC8GB None A100 ES XE.H6SPN.
Table 7-3. CPU, Memory 1 & Band (Continued) Model Country P/N CPU Memory1 Band A100 PH XE.H6RAN.006 NV-TEGRA250 eMMC8GB None A100 PH XE.H6SAN.005 NV-TEGRA250 eMMC16GB None A100 PL XE.H6REN.012 NV-TEGRA250 eMMC8GB None A100 PL XE.H6SEN.010 NV-TEGRA250 eMMC16GB None A100 RU XE.H6REN.007 NV-TEGRA250 eMMC8GB None A100 RU XE.H6SEN.006 NV-TEGRA250 eMMC16GB None A100 SG XE.H6RAN.007 NV-TEGRA250 eMMC8GB None A100 SG XE.H6SAN.
Table 7-4. Wifi Module, Battery & Adapter Model Country P/N Wifi Module Battery Adapter A100 AU/NZ XE.H6RAN.001 WiFi Module 2CELL1.53 18W A100 AU/NZ XE.H6SAN.001 WiFi Module 2CELL1.53 18W A100 BE XE.H6REN.005 WiFi Module 2CELL1.53 18W A100 BE XE.H6SEN.001 WiFi Module 2CELL1.53 18W A100 CA XE.H6RPN.004 WiFi Module 2CELL1.53 18W A100 CA XE.H6SPN.001 WiFi Module 2CELL1.53 18W A100 ES XE.H6RPN.005 WiFi Module 2CELL1.53 18W A100 ES XE.H6SPN.
Table 7-4. Wifi Module, Battery & Adapter (Continued) Model Country P/N Wifi Module Battery Adapter A100 PH XE.H6RAN.006 WiFi Module 2CELL1.53 18W A100 PH XE.H6SAN.005 WiFi Module 2CELL1.53 18W A100 PL XE.H6REN.012 WiFi Module 2CELL1.53 18W A100 PL XE.H6SEN.010 WiFi Module 2CELL1.53 18W A100 RU XE.H6REN.007 WiFi Module 2CELL1.53 18W A100 RU XE.H6SEN.006 WiFi Module 2CELL1.53 18W A100 SG XE.H6RAN.007 WiFi Module 2CELL1.53 18W A100 SG XE.H6SAN.
A101 0 Table 7-5. BOM Name, RO & NS Model Country P/N BOM Name RO NS A101 AU/NZ XE.H6TAN.001 A101_8u900770W AAP ACA A101 AU/NZ XE.H6UAN.001 A101_16u900770W AAP ACA A101 AU/NZ XE.H6VAN.003 A101_8u3G5521GW AAP ACA A101 AU/NZ XE.H6WAN.001 A101_16u3G5521GW AAP ACA A101 BE XE.H6TEN.005 A101_8u900770W EMEA ACH A101 BE XE.H6UEN.013 A101_16u900770W EMEA ACH A101 BE XE.H6VEN.005 A101_8u3G5521GW EMEA ACH A101 BE XE.H6WEN.
Table 7-5. BOM Name, RO & NS (Continued) Model Country P/N BOM Name RO NS A101 IN XE.H6VAN.004 A101_8u3G5521GW AAP AIL A101 IN XE.H6WAN.002 A101_16u3G5521GW AAP AIL A101 IT XE.H6TEN.003 A101_8u900770W EMEA AIT A101 IT XE.H6UEN.001 A101_16u900770W EMEA AIT A101 IT XE.H6VEN.002 A101_8u3G5521GW EMEA AIT A101 IT XE.H6WEN.001 A101_16u3G5521GW EMEA AIT A101 MOYO XE.H6TEN.010 A101_8u900770W EMEA AME A101 MOYO XE.H6UEN.
Table 7-5. BOM Name, RO & NS (Continued) Model Country P/N BOM Name RO NS A101 RU XE.H6WEN.004 A101_16u3G5521GW EMEA ACR A101 SG XE.H6TAN.007 A101_8u900770W AAP ACS A101 SG XE.H6UAN.006 A101_16u900770W AAP ACS A101 SG XE.H6VAN.009 A101_8u3G5521GW AAP ACS A101 SG XE.H6WAN.006 A101_16u3G5521GW AAP ACS A101 TH XE.H6TAN.008 A101_8u900770W AAP ATH A101 TH XE.H6UAN.007 A101_16u900770W AAP ATH A101 TH XE.H6VAN.001 A101_8u3G5521GW AAP ATH A101 TH XE.H6WAN.
Table 7-5. BOM Name, RO & NS (Continued) Model Country P/N BOM Name RO NS A101 WW S7.H6TWN.014 A101_8u900770W WW WW A101 WW S7.H6TWN.015 A101_8u900770W WW WW A101 WW S7.H6VWN.001 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.002 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.003 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.004 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.005 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.006 A101_8u3G5521GW WW WW A101 WW S7.H6VWN.
Table 7-6. Description & Mobile Device Model Country P/N Description Mobile Device A101 AU/NZ XE.H6TAN.001 A101 Tablet 900 AAP_GEN4 AndroidAU-Tab-1 AU- Blue EM770W N N Tablet A101 AU/NZ XE.H6UAN.001 A101 Tablet 900 AAP_GEN4 AndroidAU-Tab-1 AU- Blue EM770W_16G N N Tablet A101 AU/NZ XE.H6VAN.003 A101 Tablet 3G AAP_GEN4 AndroidAU-Tab-1 AU- Blue F5521gw N N Tablet A101 AU/NZ XE.H6WAN.001 A101 Tablet 3G AAP_GEN4 AndroidAU-Tab-1 AU- Blue F5521gw_16G N N Tablet A101 BE XE.H6TEN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N A101 Eastern Europe XE.H6VEN.013 A101 Tablet 3G EMEA_GEN3 AndroidEE-Tab-1 EU- Blue F5521gw N N Tablet A101 Eastern Europe XE.H6WEN.011 A101 Tablet 3G EMEA_GEN3 AndroidEE-Tab-1 EU- Blue F5521gw_16G N N Tablet A101 GCTWN XE.H6TTN.001 A101 Tablet 900 AAP_GEN4TW AndroidTW-Tab-1 US- Blue EM770W N N Tablet A101 GCTWN XE.H6UTN.001 A101 Tablet 900 AAP_GEN4TW AndroidTW-Tab-1 US- Blue EM770W_16G N N Tablet A101 GCTWN XE.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 IN XE.H6TAN.002 A101 Tablet 900 AAP_GEN4 AndroidIN-Tab-1 EU- Blue EM770W N N Tablet A101 IN XE.H6UAN.002 A101 Tablet 900 AAP_GEN4 AndroidIN-Tab-1 EU- Blue EM770W_16G N N Tablet A101 IN XE.H6VAN.004 A101 Tablet 3G AAP_GEN4 AndroidIN-Tab-1 EU- Blue F5521gw N N Tablet A101 IN XE.H6WAN.002 A101 Tablet 3G AAP_GEN4 AndroidIN-Tab-1 EU- Blue F5521gw_16G N N Tablet A101 IT XE.H6TEN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 MX XE.H6VPN.004 A101 Tablet 3G EMEA_GEN3 AndroidMexico-Tab-1 US- Blue F5521gw N N Tablet A101 MX XE.H6WPN.002 A101 Tablet 3G EMEA_GEN3 AndroidMexico-Tab-1 US- Blue F5521gw_16G N N Tablet A101 MY XE.H6TAN.004 A101 Tablet 900 AAP_GEN4 AndroidMY-Tab-1 UK- Blue EM770W N N Tablet A101 MY XE.H6UAN.004 A101 Tablet 900 AAP_GEN4 AndroidMY-Tab-1 UK- Blue EM770W_16G N N Tablet A101 MY XE.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 PL XE.H6TEN.012 A101 Tablet 900 EMEA_GEN6 AndroidPL EU- Blue EM770W N N Tablet A101 PL XE.H6UEN.010 A101 Tablet 900 EMEA_GEN6 AndroidPL EU- Blue EM770W_16G N N Tablet A101 PL XE.H6VEN.012 A101 Tablet 3G EMEA_GEN6 AndroidPL EU- Blue F5521gw N N Tablet A101 PL XE.H6WEN.009 A101 Tablet 3G EMEA_GEN6 AndroidPL EU- Blue F5521gw_16G N N Tablet A101 RU XE.H6TEN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 TH XE.H6VAN.001 A101 Tablet 3G AAP_GEN4 AndroidTH-Tab-1 EU- Blue F5521gw N N Tablet A101 TH XE.H6WAN.007 A101 Tablet 3G AAP_GEN4 AndroidTH-Tab-1 EU- Blue F5521gw_16G N N Tablet A101 TR XE.H6TEN.009 A101 Tablet 900 EMEA_CUS5TR AndroidTR-4 EU- Blue EM770W N N Tablet A101 TR XE.H6UEN.004 A101 Tablet 900 EMEA_CUS5TR AndroidTR-4 EU- Blue EM770W_16G N N Tablet A101 TR XE.H6VEN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 VN XE.H6TAN.009 A101 Tablet 900 AAP_GEN4 AndroidVN-Tab-1 EU- Blue EM770W N N Tablet A101 VN XE.H6UAN.008 A101 Tablet 900 AAP_GEN4 AndroidVN-Tab-1 EU- Blue EM770W_16G N N Tablet A101 VN XE.H6VAN.002 A101 Tablet 3G AAP_GEN4 AndroidVN-Tab-1 EU- Blue F5521gw N N Tablet A101 VN XE.H6WAN.008 A101 Tablet 3G AAP_GEN4 AndroidVN-Tab-1 EU- Blue F5521gw_16G N N Tablet A101 WW S7.H6TWN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 WW S7.H6VWN.001 A101 Sample 3G Bar-type HSUPA 7.0 WSVGA Blue AU plug N N Tablet A101 WW S7.H6VWN.002 A101 Sample 3G Bar-type HSUPA 7.0 WSVGA Blue CN plug N N Tablet A101 WW S7.H6VWN.003 A101 Sample 3G Bar-type HSUPA 7.0 WSVGA Blue EU plug N N Tablet A101 WW S7.H6VWN.004 A101 Sample 3G Bar-type HSUPA 7.0 WSVGA Blue UK plug N N Tablet A101 WW S7.H6VWN.
Table 7-6. Description & Mobile Device (Continued) Model Country P/N Description Mobile Device A101 West EU-1 XE.H6UEN.007 A101 Tablet 900 EMEA_GEN3 AndroidWEU4 EU- Blue EM770W_16G N N Tablet A101 West EU-1 XE.H6UEN.008 A101 Tablet 900 EMEA_GEN3 AndroidWEU5 EU- Blue EM770W_16G N N Tablet A101 West EU-1 XE.H6VEN.001 A101 Tablet 3G EMEA_GEN1 AndroidWEU3 EUUK Blue F5521gw N N Tablet A101 West EU-1 XE.H6VEN.
Table 7-7. CPU, Memory 1 & Band (Continued) Model Country P/N CPU Memory1 Band A101 AU/NZ XE.H6VAN.003 NV-TEGRA250 eMMC8GB 3G A101 AU/NZ XE.H6WAN.001 NV-TEGRA250 eMMC16GB 3G A101 BE XE.H6TEN.005 NV-TEGRA250 eMMC8GB 900 A101 BE XE.H6UEN.013 NV-TEGRA250 eMMC16GB 900 A101 BE XE.H6VEN.005 NV-TEGRA250 eMMC8GB 3G A101 BE XE.H6WEN.013 NV-TEGRA250 eMMC16GB 3G A101 CA XE.H6TPN.004 NV-TEGRA250 eMMC8GB 900 A101 CA XE.H6UPN.003 NV-TEGRA250 eMMC16GB 900 A101 CA XE.
Table 7-7. CPU, Memory 1 & Band (Continued) Model Country P/N CPU Memory1 Band A101 IT XE.H6WEN.001 NV-TEGRA250 eMMC16GB 3G A101 MOYO XE.H6TEN.010 NV-TEGRA250 eMMC8GB 900 A101 MOYO XE.H6UEN.009 NV-TEGRA250 eMMC16GB 900 A101 MOYO XE.H6VEN.010 NV-TEGRA250 eMMC8GB 3G A101 MOYO XE.H6WEN.008 NV-TEGRA250 eMMC16GB 3G A101 MX XE.H6TPN.003 NV-TEGRA250 eMMC8GB 900 A101 MX XE.H6UPN.001 NV-TEGRA250 eMMC16GB 900 A101 MX XE.H6VPN.
Table 7-7. CPU, Memory 1 & Band (Continued) Model Country P/N CPU Memory1 Band A101 TH XE.H6TAN.008 NV-TEGRA250 eMMC8GB 900 A101 TH XE.H6UAN.007 NV-TEGRA250 eMMC16GB 900 A101 TH XE.H6VAN.001 NV-TEGRA250 eMMC8GB 3G A101 TH XE.H6WAN.007 NV-TEGRA250 eMMC16GB 3G A101 TR XE.H6TEN.009 NV-TEGRA250 eMMC8GB 900 A101 TR XE.H6UEN.004 NV-TEGRA250 eMMC16GB 900 A101 TR XE.H6VEN.009 NV-TEGRA250 eMMC8GB 3G A101 TR XE.H6WEN.010 NV-TEGRA250 eMMC16GB 3G A101 UK XE.H6TEN.
Table 7-7. CPU, Memory 1 & Band (Continued) Model Country P/N CPU Memory1 Band A101 WW S7.H6VWN.004 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.005 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.006 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.007 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.008 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.009 NV-TEGRA250 eMMC8GB 3G A101 WW S7.H6VWN.010 NV-TEGRA250 eMMC8GB 3G A101 West EU-1 XE.H6TEN.
Table 7-8. Wifi Module, Battery & Adapter (Continued) Model Country P/N Wifi Module Battery Adapter A101 BE XE.H6VEN.005 WiFi Module 2CELL1.53 18W A101 BE XE.H6WEN.013 WiFi Module 2CELL1.53 18W A101 CA XE.H6TPN.004 WiFi Module 2CELL1.53 18W A101 CA XE.H6UPN.003 WiFi Module 2CELL1.53 18W A101 CA XE.H6VPN.003 WiFi Module 2CELL1.53 18W A101 CA XE.H6WPN.001 WiFi Module 2CELL1.53 18W A101 Eastern Europe XE.H6TEN.014 WiFi Module 2CELL1.
Table 7-8. Wifi Module, Battery & Adapter (Continued) Model Country P/N Wifi Module Battery Adapter A101 MOYO XE.H6WEN.008 WiFi Module 2CELL1.53 18W A101 MX XE.H6TPN.003 WiFi Module 2CELL1.53 18W A101 MX XE.H6UPN.001 WiFi Module 2CELL1.53 18W A101 MX XE.H6VPN.004 WiFi Module 2CELL1.53 18W A101 MX XE.H6WPN.002 WiFi Module 2CELL1.53 18W A101 MY XE.H6TAN.004 WiFi Module 2CELL1.53 18W A101 MY XE.H6UAN.004 WiFi Module 2CELL1.53 18W A101 MY XE.H6VAN.
Table 7-8. Wifi Module, Battery & Adapter (Continued) Model Country P/N Wifi Module Battery Adapter A101 TR XE.H6TEN.009 WiFi Module 2CELL1.53 18W A101 TR XE.H6UEN.004 WiFi Module 2CELL1.53 18W A101 TR XE.H6VEN.009 WiFi Module 2CELL1.53 18W A101 TR XE.H6WEN.010 WiFi Module 2CELL1.53 18W A101 UK XE.H6TEN.006 WiFi Module 2CELL1.53 18W A101 UK XE.H6UEN.002 WiFi Module 2CELL1.53 18W A101 UK XE.H6VEN.006 WiFi Module 2CELL1.53 18W A101 UK XE.H6WEN.
Table 7-8. Wifi Module, Battery & Adapter (Continued) Model Country P/N Wifi Module Battery Adapter A101 WW S7.H6VWN.008 WiFi Module 2CELL1.53 18W A101 WW S7.H6VWN.009 WiFi Module 2CELL1.53 18W A101 WW S7.H6VWN.010 WiFi Module 2CELL1.53 18W A101 West EU-1 XE.H6TEN.001 WiFi Module 2CELL1.53 18W A101 West EU-1 XE.H6TEN.002 WiFi Module 2CELL1.53 18W A101 West EU-1 XE.H6TEN.004 WiFi Module 2CELL1.53 18W A101 West EU-1 XE.H6UEN.003 WiFi Module 2CELL1.
CHAPTER 8 Test Compatible Components
Android OS Environment Test. . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 A100/A101. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Android OS environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the ICONIA Tab A100/A101. Compatibility Test Report released by the Acer Mobile System Testing Department.
Android OS Environment Test 0 A100/A101 0 Table 8-1. A100/A101 Vendor Type Description P/N 3G 60027216 ERICSSON F5521gw Ericsson F5521gw LC.21300.056 60027216 ERICSSON F5521gw-NB Ericsson F5521gw-NB LC.21300.077 PLM00023 Huawei EM770W Huawei EM770W LC.21300.008 PLM00023 Huawei EM770W-Tablet Huawei EM770W-Tablet LC.21300.071 PLM00023 Huawei EM820W Huawei EM820W LC.21300.068 18W Adapter PHIHONG 18W 12V/1.5A Black PSA18R-120P(AI)-R LF AP.0180P.002 60001921 SANYO 2CELL1.
Table 8-1. A100/A101 (Continued) Vendor Type Description P/N LCD2 10001022 CMI H7WSVGA LED LCD CMI 7'' WSVGA Glare AT070TNA2 V1 LF 250nit 5ms LK.0700D.001 Camera Module Camera Module CHICONY 5M AF CJAA525 Socket Micro SOC5140 MIPI COB QM.05M06.004 Camera Module Camera Module Chicony 5M FF 725-08315LHA01 QM.05M06.001 10001079 SYNNEX eMMC16GB eMMC SanDisk Memory eMMC SDIN4C2-16G 32nm IC.0160B.001 10001079 SYNNEX eMMC8GB eMMC SanDisk Memory SDIN4C2-8G 43nm IC.0080B.
Table 8-1. A100/A101 (Continued) Vendor Type Description P/N 60003533 YOSUN eMMC16GB IC Samsung Memory KLMAG4FEJA-A001 27nm v4.41 IC.01609.004 60003533 YOSUN eMMC8GB IC Samsung Memory v4.41 KLM8G2FEJA-A001 32nm IC.08009.003 60004668 ELPIDA LPDDR2 IC Elpida Memory 168b PoP EDB8132B2PB-6D-F 40nm 8Gb IC.0800E.001 60004668 ELPIDA LPDDR2 IC Elpida Memory 168b PoP EDB4032B2PB-6D-F 40nm IC.0400E.001 60024207 KINGSTONFAR EAST eMMC8GB IC Kingston Memory KE44B-26BN/8GB 4.41 IC.0800D.
CHAPTER 9 Online Support Information
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Online Support Information Introduction 0 This section describes online technical support services available to help users repair their Acer Systems. For distributors, dealers, ASP or TPM, please refer the technical queries to a local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
9-4 Online Support Information