Ferrari 1200 Series Service Guide Service guide files and updates are available on the ACER/CSD web; for more information, please refer to http://csd.acer.com.
Revision History Please refer to the table below for the updates made on Ferrari 1200 Series service guide.
Copyright Copyright © 2008 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of Acer Incorporated. Disclaimer The information in this guide is subject to change without notice.
Conventions The following conventions are used in this manual: IV SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives bits and pieces of additional information related to the current topic. WARNING Alerts you to any damage that might result from doing or not doing specific actions. CAUTION Gives precautionary measures to avoid possible hardware or software problems. IMPORTANT Reminds you to do specific actions relevant to the accomplishment of procedures.
Preface Before using this information and the product it supports, please read the following general information. 1. This Service Guide provides you with all technical information relating to the BASIC CONFIGURATION decided for Acer's "global" product offering. To better fit local market requirements and enhance product competitiveness, your regional office MAY have decided to extend the functionality of a machine (e.g. add-on card, modem, or extra memory capability).
VI
Table of Contents Chapter one System Specifications 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Your Acer Notebook tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Right View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Removing the Lower Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 Removing the DIMM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 Removing the WLAN Board Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 Removing the Hard Disk Drive Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 Main Unit Disassembly Process . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Appendix A Model Definition and Configuration 148 Appendix B Test Compatible Components 149 Microsoft® Windows® Vista Environment Test . . . . . . . . . . . . . . . . . . . . . . . . . . . .
X
Chapter 1 System Specifications Features Below is a brief summary of the computer’s many feature: Platform AMD Better By Design program, featuring: • AMD Turion™ X2 Ultra dual-core mobile processor • AMD Turion™ X2 dual-core mobile processor • AMD Athlon™ X2 dual-core mobile processor • AMD M780G Chipset • Acer InviLink™ Nplify™ 802.11b/g/Draft-N, or • Acer InviLink™ 802.
international language support • Empowering Key • Easy-launch buttons featuring capacitive technology: email, Internet, programmable, Ferrari World • Front-access switches: WLAN, Bluetooth® Audio • Dolby®-certified surround sound system with two built-in stereo speakers • High-definition audio support • S/PDIF (Sony/Philips Digital Interface) support for digital speakers • MS-Sound compatible • Acer PureZone technology with two built-in stereo microphones featuring beam forming, echo cancella
System Block Diagram PCB Layer Stackup DIMM1 DDR2 SODIMM DIMM2 DDR II 667/800 DDR II 667/800 New card Mini Card Port Replicator Giffin S1g2 Socket OUT Power Switch G577BR91U Project code:91.4BA01.001 PCB P/N :08225 AMD 16x16 USB RJ45/CRT//DVI-D/SPDIF/MIC in/Line in/Line out/AC Jack HyperTransport IN DDR2 SODIMM PCI-E x 1 PCI-E x 1 CPU V_CORE ISL6265HR INPUT LAN XFORM Broadcom 5764M PCI-E x 1 CLK GEN. RS780M INPUT INT.
Your Acer Notebook tour After knowing your computer features, let us show you around your new Ferrari computer. Front View Icon 4 Item Description 1 Acer Crystal Eye webcam Web camera for video communication. 2 Display screen Also called Liquid-Crystal Display (LCD), displays computer output. 3 Empowering key Lanuch Acer Empowering Technology 4 Power button Turns the computer on and off. 5 Keyboard For entering data into your computer.
Icon Item Description 8 Speakers Left and right speakers deliver stereo audio output. 9/13 Status indicators Light-Emitting Diodes (LEDs) that light up to show the status of the computer's functions and components. 10 Click buttons (left and right) The left and right buttons function like the left and right mouse buttons. 11 Acer BioProtection fingerprint reader Acer Bio-Protection fingerprint reader supporting Acer FingerNav 4-way control function.
Closed Front View Icon 6 Item Description 1 4-pin IEEE 1394 port Connects to IEEE 1394 devices. 2 Headphones/ speaker/line-out jack with S/PDIF support Connects to audio line-out devices (e.g., speakers, headphones). 3 Line-in jack Accepts audio line-in devices (e.g., audio CD player, stereo walkman). 4 Microphone-in jack Accepts input from external microphones. 5 Easy-launch buttons Buttons for launching frequently used programs. 6 Infrared port Interfaces with infrared devices (e.g.
Left View # Icon Item Description 1 Ventilation slots Enable the computer to stay cool, even after prolonged use. 2 Ethernet (RJ-45) port Connects to an Ethernet 10/100-based network. 3 2 USB 2.0 ports Connect to USB 2.0 devices (e.g., USB mouse, USB camera). 4 ExpressCard/54 slot Accepts one ExpressCard/54 module.
Icon 7 8 Item Modem (RJ-11) port Description Connects to a phone line.
Rear View # Icon Item Description 1 Kensington lock slot Connects to a Kensington-compatible computer security lock. 2 Acer EasyPort I connector Connects to Acer EasyPort IV. 3 External display (VGA) port Connects to a display device (e.g., external monitor, LCD projector).
Base View # 10 Icon Item Description 1 Battery bay Houses the computer's battery pack. 2 Battery lock Locks the battery in position 3 Battery release latch Releases the battery for removal. 4 Memory compartment Houses the computer’s main memory. 5 Acer Disk AntiShock Protection (DASP) Protects the hard disk drive from shorcks and bumps. 6 Ventilation slots and cooling fan Enable the computer to stay cool, even after prolonged use.
Bluetooth optical mouse # Icon Item Description 1 Left click button Press the left button to perform selection and execution functions. 2 Scroll wheel To scroll up or down a page. 3 Right click button Press the right button to perform selection and execution functions. 4 Status indicator Indicates the Bluetooth connection/pairing status and the mouse’s battery status. 5 Battery release latch Release the battery for removal.
Bluetooth VoIP phone (optional) Description # 12 Icon Item Description 1 ExpressCard interface connector Connects the computer’s ExpressCard interface. 2 Speaker Speaker delivers audio output. 3 Cancel button Hang up the call. Hold for at 2 seconds to power on/off. 4 Function button Hold for least 3 seconds to enable BT pairing. Switch between headset or hands-free after the call is accepted. 5 OK button Answer an incoming call. 6 Microphone Internal microphone for sound recording.
Indicators The computer has several easy-to-read status indicators: The front panel indicators are visible even when the computer cover is closed. Icon Function Description Power Indicates the computer's power status. Battery Indicates the computer's battery status. Bluetooth Indicates the status of Bluetooth communication. Wireless LAN Indicates the status of wireless LAN communication. Caps Lock Lights up when Caps Lock is activated. Num Lock Lights up when Num Lock is activated.
Press < > to run the Acer Empowering Technology. The mail and Web browser buttons are pre-set to email and Internet programs, but can be reset by users. To set the Web browser, mail and programmable buttons, run the Acer Launch Manager. Press Ferrari World to browse the Ferrari World website. Icon Description Empowering Technology Launch Acer Empowering Technology.
Function Left Button (1) Right Button Main touchpad (2) Select Click once. Tap once. Drag Click and hold, then use finger on the touchpad to drag the cursor. Tap twice (at the same speed as double-clicking a mouse button); rest your finger on the touchpad on the second tap and drag the cursor. Access context menu Click once. NOTE: When using the touchpad, keep it - and your fingers - dry and clean.
Using the Keyboard The keyboard has full-sized keys and an embedded numeric keypad, separate cursor, lock, Windows, function and special keys. Lock Keys and embedded numeric keypad The keyboard has three lock keys which you can toggle on and off. Lock key Description Caps Lock When Caps Lock is on, all alphabetic characters typed are in uppercase. Num Lock + When Num Lock is on, the embedded keypad is in numeric mode.
Windows Keys The keyboard has two keys that perform Windows-specific functions. Key Description Windows key Pressed alone, this key has the same effect as clicking on the Windows Start button; it launches the Start menu.
Hot Keys The computer employs hotkeys or key combinations to access most of the computer’s controls like sreen brightness, volume output and the BIOS utility. To activate hot keys, press and hold the key before pressing the other key in the hotkey combination. Hotkey 18 Icon Function Description + Hotkey help Displays help on hotkeys. + Acer eSettings Management Launches Acer eSettings Management in Acer Empowering Technology.
Special Key You can locate the Euro symbol and the US dollar sign at the upper-center and/or bottom-right of your keyboard. The Euro symbol 1. Open a text editor or word processor. 2. Hold and then press the <5> key at the upper-center of the keyboard. NOTE: Note: Some fonts and software do not support the Euro symbol. Please refer to www.microsoft.com/ typography/faq/faq12.htm for more information. The US dollar sign 1. Open a text editor or word processor. 2.
Acer Empowering Technology The Empowering Technology toolbar makes it easy for you to access frequently used functions and manage your new Acer system. Displayed by default in the upper half of your screen, it provides access to the following utilities: • Acer eNet Management hooks up to location-based networks intelligently. • Acer ePower Management optimizes battery usage via customizable power plans. • Acer ePresentation Management connects to a projector and adjusts display settings.
Acer eNet Management can save network settings for a location to a profile, and automatically switch to the appropriate profile when you move from one location to another. Settings stored include network connection settings (IP and DNS settings, wireless AP details, etc.), as well as default printer settings. Security and safety concerns mean that Acer eNet Management does not store username and password information.
Acer ePower Management Acer ePower Management features a straightforward user interface for configuring your power management options. To access this utility, select "Acer ePower Management" from the Empowering Technology toolbar, run the program from the Acer Empowering Technology program group in Start menu, or right-click the Windows power icon in the system tray and select "Acer ePower Management".
To switch between power plans: 1. Select the power plan you wish to switch to from the drop-down list. 2. Click "Apply". To edit a power plan: Editing a power plan allows you to adjust system settings like LCD brightness and CPU speed. You can also turn on/off system components to extend battery life. 1. Switch to the power plan you wish to edit 2. Adjust settings as required. 3. Click "Apply" to save your new settings.
Acer eAudio Management Acer eAudio Management allows you to easily control the enhanced sound effects of Dolby® Home Theater™ on your system. Select "Movie" or "Game" mode to experience the awesome realism of 5.1-channel surround sound from just 2 speakers, via Dolby Virtual Speaker technology. "Music" mode lets you enjoy your favorite tunes, in vivid detail.
NOTE: If the restored resolution is not correct after disconnecting a projector, or you need to use an external resolution that is not supported by Acer ePresentation Management, adjust your display settings using Display Properties or the utility provided by the graphics vendor. Acer eDataSecurity Management (for selected models) Acer eDataSecurity Management is an encryption utility that protects your files from being accessed by unauthorized persons.
The Acer eDataSecurity Management setup wizard will prompt you for a supervisor password and default encryption password. This password will be used to encrypt files by default, or you can choose to enter your own password when encrypting a file. NOTE: The password used to encrypt a file is the unique key that the system needs to decrypt it. If you lose the password, the supervisor password is the only other key capable of decrypting the file.
Acer eLock Management Acer eLock Management is simple yet effective utility that allows you to lock removable storage, optical and floppy drive devices to ensure that data can't be stolen while your system is unattended. • Removable Storage Devices — includes USB disk drives, USB pen drives, USB flash drives, USB MP3 drives, USB memory card readers, IEEE 1394 disk drives, and any other removable storage devices that can be mounted as a file system when plugged into the system.
•User backup image •Current system configuration •Application • backup Restore and recovery: •Factory default image •User backup image •From previously-created CD/DVD •Reinstall applications/drivers NOTE: If your computer did not come with a Recovery CD or System CD, please use Acer eRecovery Management's "System backup to optical disc" feature to burn a backup image to CD or DVD.
• Lets you set an asset tag for your system. Windows Mobility Center The Windows Mobility Center collects key mobile-related system settings in one easy-to-find place, so you can quickly configure your Acer system to fit the situation as you change locations, networks or activities. Settings include display brightness, power plan, volume, wireless networking on/off, external display settings, display orientation and synchronization status.
• 30 Start Windows Mobility Center from the Accessories program group in the Start menu.
Using the System Utilities Acer GridVista (dual-display compatible) NOTE: This feature is only available on certain models. To enable the dual monitor feature of the notebook, first ensure that the second monitor is connected, then select Start, Control Panel, Display and click on Settings. Select the secondary monitor (2) icon in the display box and then click the check box Extend my windows desktop onto this monitor. Finally, click Apply to confirm the new settings and click OK to complete the process.
NOTE: Please ensure that the resolution setting of the second monitor is set to the manufacturer's recommended value. Launch Manager Launch Manager allows you to set the four easy-launch buttons located above the keyboard. You can access the Launch Manager by clicking on Start > All Programs > Launch Manager to start the application. Norton Internet Security Norton Internet Security is an anti-virus utility that can protect against viruses, keeping your data safe and secure.
3. Select Run Scan to scan your system. 4. When the scan is complete, review the results of the scan. NOTE: For optimal security, run a Full System Scan when scanning your computer for the first time. You can schedule customized virus scans that run unattended on specific dates and times or at periodic intervals. If you are using the computer when the scheduled scan begins, it runs in the background so that you do not have to stop working.
Hardware Specifications and Configurations Processor Item Specification CPU type AMD Turion™ X2 Dual-Core Mobile processor RM-70/RM-72/RM74/RM-75 (1000KB L2 cache, 2.0/2.1/2.2/2.2 GHz), supporting AMD HyperTransport™ 3.0 technology AMD Turion™ X2 Ultra Dual-Core Mobile Processor ZM-80/ZM82/ZM-84/ZM-85/ZM-86/ZM-87 (2000KB L2 cache, 2.1/2.2/2.3/23/ 2.4/2.4 GHz), supporting AMD HyperTransport™ 3.
OS shut down at 105 ° C; H/W shot down at 110 ° .C BIOS Item Specification BIOS vendor Phoenix BIOS Version 1.02 (MP version) BIOS ROM type SST/AMD 1MB CMOS Boot Block Flash Memory BIOS ROM size 1M byte FLASH ROM SST BIOS package 10-lead TSOP (10mmx20mm) Supported protocols ACPI 1.0b/2.0/3.0 compliance, PCI 2.2, System/HDD Password Security Control, INT 13H Extenstions, PnP BIOS 1.0a SMBIOS 2.4, BIOS Boot Specification, Simple Boot Flag 1.
Memory Combinations Slot 1 Slot 2 Total Memory 0MB 256MB 256MB 0MB 512MB 512MB 0MB 1024MB 1024MB 0MB 2048MB 2048MB 256MB 256MB 512MB 256MB 512MB 768MB 256MB 1024MB 1280MB 256MB 2048MB 2304MB 512MB 256MB 768MB 512MB 512MB 1024MB 512MB 1024MB 1536MB 512MB 2048MB 2560MB 1024MB 0MB 1024MB 1024MB 256MB 1280MB 1024MB 512MB 1536MB 1024MB 1024MB 2048MB 1024MB 2048MB 3072MB 2048MB 0MB 2048MB 2048MB 256MB 2304MB 2048MB 512MB 2560MB 2048MB 1024MB 3072MB
Bluetooth Interface Item Specification Connector type USB Wireless Module 802.11b/g Item Specification Chipset Acer InviLink™ Nplify™ 802.11a/b/g/Draft-N Wi-Fi CERTIFIED® network connection, supporting Acer SignalUp™ wireless technology, or Acer InviLink™ 802.11b/g Wi-Fi CERTIFIED® network connection, supporting Acer SignalUp™ wireless technology Data throughput 11~54 Mbps, up to 270 Mbps for Draft-N Protocol 802.
Hard Disk Drive Interface Item Voltage tolerance 5V(DC) +/- 5% 5V(DC) +/- 5% 5V(DC) +/- 5% Super-Multi Drive module Item Specification Vendor & model name PANASONIC Super-Multi DRIVE 9.5mm Slot DL 8X UJ-875 Performance Specification With CD Diskette With DVD Diskette Transfer rate (KB/sec) Sustained: Max 3.6Mbytes/sec Sustained: Max 10.
Audio Interface Item Specification Audio Controller Realtek ALC883 Azalia and Amplifier Maxim MAX9710 & MAX4411 Audio onboard or optional Built-in Mono or Stereo Stereo Resolution 18 bit stereo full duplex Compatibility HD audio Interface; S/PDIF output for PCM or AC-3 content Sampling rate 1Hz resolution VSR (Variable Sampling Rate) Internal microphone Yes Internal speaker / Quantity Yes/2 (1.
Keyboard Item Specification Keyboard controller NS PC97541V Total number of keypads 84-/85-key Windows logo key Yes Internal & external keyboard work simultaneously Plug USB keyboard to the USB port directly: Yes Battery Item Specification Vendor & model name Panasonic 3S2P Battery Type Li-ion Pack capacity 6Cell 2.9 MAH Number of battery cell 6 Package configuration 3 cells in series, 2 series in parallel Normal voltage 11.1V Charge voltage 19.0 v LCD 12.
LCD 12.1” inch Item Specification Temperature Range( ° C) 0 to +50 -20 to +60 Operating Storage (shipping) AC Adaptor Item Specification Input rating 90V AC to 264V AC, 47Hz to 63Hz Maximum input AC current 1.7A Inrush current 220A@115VAC 220A@230VAC Efficiency 82% min. @115VAC input full load System Power Management ACPI mode Power Management Mech. Off (G3) All devices in the system are turned off completely. Soft Off (G2/S5) OS initiated shutdown.
42 Chapter 1
Chapter 2 System Utilities BIOS Setup Utility The BIOS Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/ Output System). Your computer is already properly configured and optimized, and you do not need to run this utility. However, if you encounter configuration problems, you may need to run Setup. Please also refer to Chapter 4 Troubleshooting when problem arises.
Navigating the BIOS Utility There are six menu options: Information, Main, Advanced, Security, Boot, and Exit. Follow these instructions: • To choose a menu, use the left and right arrow keys. • To choose an item, use the up and down arrow keys. • To change the value of a parameter, press F5 or F6. • A plus sign (+) indicates the item has sub-items. Press Enter to expand this item. • Press Esc while you are in any of the menu options to go to the Exit menu.
Information The Information screen displays a summary of your computer hardware information. NOTE: The system information is subject to different models. Parameter Description CPU Type This field shows the CPU type and speed of the system. CPU Speed This field shows the speed of the CPU. IDE0 Model Name This field shows the model name of HDD installed on primary IDE master. IDE0 Serial Number This field displays the serial number of HDD installed on primary IDE master.
Main The Main screen allows the user to set the system time and date as well as enable and disable boot option and recovery.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Format/Option System Time Sets the system time. The hours are displayed with 24-hour format. Format: HH:MM:SS (hour:minute:second) System Time System Date Sets the system date. Format MM/DD/YYYY (month/day/ year) System Memory This field reports the memory size of the system.
Advanced The Advanced screen allows the user to set the serial, infrared and parallel ports.
Security The Security screen contains parameters that help safeguard and protect your computer from unauthorized use.
The table below describes the parameters in this screen. Settings in boldface are the default and suggested parameter settings. Parameter Description Option Supervisor Password Is Shows the setting of the Supervisor password Clear or Set User Password Is Shows the setting of the user password. Clear or Set HDD Password Is Shows the setting of the hard disk password. Clear or Set Set Supervisor Password Press Enter to set the supervisor password.
Removing a Password Follow these steps: 1. Use the w and y keys to highlight the Set Supervisor Password parameter and press the e key. The Set Password box appears: 2. Type the current password in the Enter Current Password field and press e. 3. Press e twice without typing anything in the Enter New Password and Confirm New Password fields. The computer then sets the Supervisor Password parameter to “Clear”. 4.
If the current password entered does not match the actual current password, the screen will show you the Setup Warning. If the new password and confirm new password strings do not match, the screen will display the following message.
Boot This menu allows the user to decide the order of boot devices to load the operating system. Bootable devices includes the distette drive in module bay, the onboard hard disk drive and the CD-ROM in module bay. Information P h o e n i x Tr u s t e d C o r e ( t m ) S e t u p U t i l i t y Advanced Security Boot Main Exit Item Specific Help Boot priority order: 1: 2: 3: 4: 5: 6: 7: IDE0: XXXXXXXXXXX-(XX) CD/DVD: XXXXXXXXXXX-XXX XX-XXXX-XX PCI LAN: MBA vXX.X.
Exit The Exit screen contains parameters that help safeguard and protect your computer from unauthorized use. Information Main P h o e n i x Tr u s t e d C o r e ( t m ) S e t u p U t i l i t y Advanced Security Boot Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Load Setup Defaults Discard Changes Save Changes F1 Help Esc Exit Select Item Select Menu Exit System Setup and save your changes to CMOS.
BIOS Flash Utility The BIOS flash memory update is required for the following conditions: • New versions of system programs • New features or options • Restore a BIOS when it becomes corrupted. Use the Phlash utility to update the system BIOS flash ROM. NOTE: If you do not have a crisis recovery diskette at hand, then you should create a Crisis Recovery Diskette before you use the Phlash utility. NOTE: Do not install memory-related drivers (XMS, EMS, DPMI) when you use the Phlash.
Remove HDD/BIOS Utility This section provide you with removing HDD/BIOS method: Remove HDD Password: • If you key in wrong HDD password for three time, “HDD password error code” would display on the screen. See the image below. • If you need to solve HDD password locked problem, you can run HDD_PW.EXE 1. Key in “hdd_pw 15494 0” 2. Select “2” 3. Choose one upper-case string • 56 Reboot system and key in “0KJFN42” or “UVEIQ96” to HDD user password.
Remove BIOS Password: • Chapter 2 If you key in wrong Supervisor Password for three time, “System Disabled” would display on the screen. See the image below.
• If you need to solve BIOS password locked problem, you can run BIOS_PW.EXE 1. Key in “bios_pw 14452 0” 2. Choose one upper-case string • 58 Reboot the system and key in “qjjg9vy” or “07yqmjd” to BIOS user password.
Chapter 2 59
60 Chapter 2
Chapter 3 Machine Disassembly and Replacement This chapter contains step-by-step procedures on how to disassemble the notebook computer for maintenance and troubleshooting.
General Information Pre-disassembly Instructions Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals. 2. Unplug the AC adapter and all power and signal cables from the system. 3. Place the system on a flat, stable surface. 4. Remove the battery pack.
External Module Disassembly Process External Modules Disassembly Flowchart The flowchart below gives you a graphic representation on the entire disassembly sequence and instructs you on the components that need to be removed during servicing. For example, if you want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly frame in that order.
Removing the Battery Pack 1. Turn base unit over. 2. Slide the battery lock/unlock latch to the unlock position. 3. Slide and hold the battery release latch to the release position (1), then slide out the battery pack from the main unit (2). Removing the SD dummy card 1. 64 Push the SD dummy card all the way in to eject it.
2. Pull it out from the slot. Removing the ExpressCard dummy card 1. Push the ExpressCard dummy card all the way in to eject it. 2. Pull it out from the slot. Removing the Lower Cover 1. See “Removing the Battery Pack” on page 64.
2. Remove the three captive screws on the lower cover. 3. Use a plastic screw driver to carefully pry open the lower cover. 4. Remove the lower cover from the lower case. Removing the DIMM 66 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65..
3. Push out the latches on both sides of the DIMM socket to release the DIMM. 4. Remove the DIMM module. Removing the WLAN Board Modules 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. Disconnect the antenna cables from the WLAN board.
4. Move the antenna away from the WLAN board and remove the two screws (F) on the WLAN board to release the WLAN board. Step 1~2 5. Size (Quantity) M2 x L4 (2) Color Black Torque 1.6 kgf-cm Detach the WLAN board from the WLAN socket. NOTE: When attaching the antenna back to the WLAN board, make sure the cable are arranged properly. Removing the Hard Disk Drive Module 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3.
4. Slide out the hard disk drive module from the bay. NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it. 5. Remove the four screws (C) securing the hard disk to the bracket. Step 1~4 Chapter 3 Size (Quantity) M3 x L4 (4) Color Silver Torque 3.
Main Unit Disassembly Process Main Unit Disassembly Flowchart MAIN UNIT DISASSEMBLY MAIN UNIT KEYBOARD Ax2 MIDDLE COVER Ax4, Fx2 LCD MODULE B x 2, A x 10 Fx1 UPPER CASE Bx2 Fx2 Bx2 MAIN BOARD OPTICAL DISK DRIVE MODULE FINGERPRINT MODULE CARD READER BOARD TOUCH PAD BOARD Bx1 Ex1 Ex1 BUTTON BOARD BRACKET MODEM BOARD OPTICAL DISK DRIVE Fx2 OPTICAL LOCKER BRACKET Ex4 BUTTON BOARD Fx2 LEFT AND RIGHT SPEAKER MODULE CPU/VGA THERMAL MODULE CPU Screw List 70 Item Screw Color Part No.
Removing the Keyboard 1. See “Removing the Battery Pack” on page 64. 2. Push down on the lock and release the latches securing the keyboard to the upper case. 3. Carefully pry loose the keyboard and turn it over on the touchpad area.
4. Remove the adhesive strip over the connector. 5. Disconnect the keyboard cable from the main board to remove the keyboard. Removing the Middle Cover 1. 72 See “Removing the Battery Pack” on page 64.
2. See “Removing the Keyboard” on page 71. 3. Disconnect the switch connector from the mainboard. 4. Remove the two screws (A) securing the middle cover. Step 1~2 Chapter 3 Size (Quantity) M2.5 x L6 (2) Color Black Torque 3.
5. Carefully pry loose the middle cover and remove it from the system. Removing the LCD Module 74 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71.
5. Remove the two screws (F) from the left hinge cover and carefully pry loose and remove the left hinge cover. Step 1~2 6. Size (Quantity) M2 x L4 (2) Color Black Torque 1.6 kgf-cm Carefully pry loose the latch on the right hinge cover; close the LCD panel and then pull up the right hinge cover to remove.
7. 76 Carefully pull out the wireless antenna cables from the hole and remove any adhesive tapes securing the cables.
8. Remove the large adhesive tape by the battery bay area and carefully pull the wireless antenna cables throught the routing hole. 9. Disconnect the LCD cable connector from the main board.
10. Remove the four screws (A) from the left and right hinge of the LCD module. Step 1~4 Size (Quantity) M2.5 x L6 (4) Color Black Torque 4.0 kgf-cm 11. Carefully remove the LCD module from the base unit. NOTE: When connecting the cable back to the unit, please note that the cable should be routed well. Separating the Upper Case from the Lower Case 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3.
11. Disconnect the touchpad cable from the TPAD1 on the main board. 12. Remove the thirteen screws (2 x B, 10 x A, 1 x F) on the bottom and top panel.
Step Size (Quantity) Color Torque 1~2 M2 x L3 (2) Black 1.6 kgf-cm 3~6 M2.5 L6 (4) Black 3.0 kgf-cm 7 M2 x L4 (1) Black 1.6 kgf-cm 8~13 M2.5 L6 (6) Black 3.0 kgf-cm 13. Gently remove the upper case from the lower case. Removing the Button Board 80 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5.
9. See “Removing the Middle Cover” on page 72. 10. See “Removing the LCD Module” on page 74. 11. See “Separating the Upper Case from the Lower Case” on page 78. 12. Release the latch and disconnect the two cables from the button board.
13. Disconnect the fingerprint cable from the button board.
14. Remove the two screws (B) securing the button board bracket and remove the button board bracket together with the button board. Step 1~2 Size (Quantity) M2 x L3 (2) Color Black Torque 1.6 kgf-cm 15. Remove the one screw (B) and remove the button board from the bracket.
Step 1 Size (Quantity) M2 x L3 (1) Color Black Torque 1.6 kgf-cm Removing the Fingerprint Board Module 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71.
13. Remove the adhesive tape. 14. Remove the three screws (B) securing the fingerprint module to the upper case. Step 1~3 Size (Quantity) M2 x L3 (3) Color Black Torque 1.6 kgf-cm 15. Remove the fingerprint board module from the upper case.
Removing theTouch Pad Board Module 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9. See “Removing the Middle Cover” on page 72. 10.
Removing the Optical Drive Module 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9. See “Removing the Middle Cover” on page 72. 10.
14. Remove the one screw (G) securing the locker bracket and remove the locker bracket from the optical disk drive module. Step 1 88 Size (Quantity) M2 x L2.5 (1) Color Black Torque 1.
Removing the Main Board 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9. See “Removing the Middle Cover” on page 72. 10.
14. Disconnect the bluetooth cable from the BLUE1 on the main board. 15. Disconnect the modem cable from the MDCDK1 on the main board. 16. Disconnect the cable from the modem board.
17. Disconnect the cable from the card reader board. 18. Remove the three screws (D) securing the main board in place. Step 1~3 Size (Quantity) M2.5 x L4 (3) Color Black Torque 3.0 kgf-cm 19. Carefully remove the main board.
Removing the CPU and VGA Heatsink Module 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9. See “Removing the Middle Cover” on page 72. 10.
15. Carefully lift up the heatsink module. Removing the CPU 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9.
15. Lift up carefully to remove the CPU. NOTE: When installing the CPU, make sure to install the CPU with PIN 1 at the corner as shown. Removing the Modem Board 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7.
13. Remove the one screw (E) securing the modem card. Step 1 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.6 kgf-cm 14. Remove the modem board from the main board. Removing the Speaker Modules 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7.
12. See “Removing the Main Board” on page 89. 13. Remove any adhesive tape securing the speaker cables. 14. Remove the two screws (F) holding the left and right speakers. Step 1~2 96 Size (Quantity) M2 x L4 (2) Color Silver Torque 1.
15. Remove the left and right speakers from the upper case. Removing the Card Reader Board 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the SD dummy card” on page 64. 3. See “Removing the ExpressCard dummy card” on page 65. 4. See “Removing the Lower Cover” on page 65. 5. See “Removing the DIMM” on page 66. 6. See “Removing the WLAN Board Modules” on page 67. 7. See “Removing the Hard Disk Drive Module” on page 68. 8. See “Removing the Keyboard” on page 71. 9.
13. Remove the one screw (E) securing the bracket to the card reader board. Step 1 Size (Quantity) M2 x L4 (1) Color Silver Torque 1.6 kgf-cm 14. Remove the bracket from the card reader board. 15. Remove the card reader board from the lower case.
LCD Module Disassembly Process LCD Module Disassembly Flowchart LCD MODULE DISASSEMBLY LCD MODULE Hx6 LCD BEZEL Ix6 LCD ASSEMBLY Jx2 LCD FPC CABLE LEFT LCD BRACKET Jx2 LCD BACK PANEL RIGHT LCD BRACKET ANTENNAS VGA CAMERA Screw List Item Screw Color Part No. H M2 x L4 Black 86.00G58.725 I M2 x L4 Silver 86.00G92.524 J M2 x L3 Silver 86.00C07.
Removing the LCD Bezel 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7. Remove the four screw covers and the two rubber cover. 8. Remove the six screws (H) on the LCD module as shown. Step 1~6 100 Size (Quantity) M2 x L4 (6) Color Black Torque 1.
9. Carefully pry open the LCD bezel and place the bezel on top of the LCD panel. 10. Disconnect the microphone cable and remove the bezel from the LCD panel.
Removing the LCD module with the Brackets 102 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7. See “Removing the LCD Bezel” on page 100. 8. Disconnect the cable from the web camera.
9. Remove the six screws (I) securing the LCD module. Step 1~6 Size (Quantity) M2 x L4 (6) Color Silver Torque 1.6 kgf-cm 10. Remove the LCD with the brackets from the back cover. Removing the FPC Cable 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7.
9. Disconnect the inverter board cable from its connector. 10. Detach the acetic tapes holding the FPC cable from the LCD panel and detach the acetic tape securing the FPC connector.
11. Disconnect the FPC cable from the LCD panel. Removing the LCD Brackets 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7. See “Removing the LCD Bezel” on page 100. 8. See “Removing the LCD module with the Brackets” on page 102. 9.
10. Remove the four screws (J) securing the left and right LCD brackets to remove the brackets. Step 1~4 Size (Quantity) M2 x L3 (4) Color Silver Torque 1.6 kgf-cm Removing the Antennas 106 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7.
10. Remove the tapes holding the antenna cables in place and release the cables from the latches. 11. Remove the antenna cables from the back cover.
Removing the Web Camera 108 1. See “Removing the Battery Pack” on page 64. 2. See “Removing the Lower Cover” on page 65. 3. See “Removing the WLAN Board Modules” on page 67. 4. See “Removing the Keyboard” on page 71. 5. See “Removing the Middle Cover” on page 72. 6. See “Removing the LCD Module” on page 74. 7. See “Removing the LCD Bezel” on page 100. 8. See “Removing the LCD module with the Brackets” on page 102. 9. Remove the Web camera from the back cover.
Chapter 4 Troubleshooting Use the following procedure as a guide for computer problems. NOTE: The diagnostic tests are intended to test only Acer products. Non-Acer products, prototype cards, or modified options can give false errors and invalid system responses. 1. Obtain the failing symptoms in as much detail as possible. 2. Verify the symptoms by attempting to re-create the failure by running the diagnostic test or by repeating the same operation. 3.
System Check Procedures External Diskette Drive Check Do the following to isolate the problem to a controller, driver, or diskette. A write-enabled, diagnostic diskette is required. NOTE: Make sure that the diskette does not have more than one label attached to it. Multiple labels can cause damage to the drive or cause the drive to fail. Do the following to select the test device. 1. Boot from the diagnostics diskette and start the diagnostics program. 2.
• External keyboard If any of these devices do not work, reconnect the cable connector and repeat the failing operation. Memory check Memory errors might stop system operations, show error messages on the screen, or hang the system. 1. Boot from the diagnostics diskette and start the doagmpstotics program (please refer to main board. 2. Go to the diagnostic memory in the test items. 3. Press F2 in the test items. 4. Follow the instructions in the message window.
Check the Power Adapter Unplug the power adapter cable from the computer and measure the output voltage at the plug of the power adapter cable. See the following figure Pin 1: +19 to +20.5V Pin 2: 0V, Ground 1. If the voltage is not correct, replace the power adapter. 2. If the voltage is within the range, do the following: • Replace the System board. • If the problem is not corrected, see “Undetermined Problems” on page 129. • If the voltage is not correct, go to the next step.
Check the Battery Pack To check the battery pack, do the following: From Software: 1. Check out the Power Management in control Panel 2. In Power Meter, confirm that if the parameters shown in the screen for Current Power Source and Total Battery Power Remaining are correct. 3. Repeat the steps 1 and 2, for both battery and adapter. 4. This helps you identify first the problem is on recharging or discharging. From Hardware: 1. Power off the computer. 2.
Power-On Self-Test (POST) Error Message The POST error message index lists the error message and their possible causes. The most likely cause is listed first. NOTE: Perform the FRU replacement or actions in the sequence shown in FRU/Action column, if the FRU replacement does not solve the problem, put the original part back in the computer. Do not replace a non-defective FRU. This index can also help you determine the next possible FRU to be replaced when servicing a computer.
Index of Error Messages Error Code List Error Codes Error Messages 006 Equipment Configuration Error Causes: 1. CPU BIOS Update Code Mismatch 2. IDE Primary Channel Master Drive Error (THe causes will be shown before “Equipment Configuration Error”) 010 Memory Error at xxxx:xxxx:xxxxh (R:xxxxh, W:xxxxh) 070 Real Time Clock Error 071 CMOS Battery Bad 072 CMOS Checksum Error 110 System disabled. Incorrect password is specified.
Error Message List Error Messages 116 FRU/Action in Sequence System timer error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Real time clock error RTC battery Run BIOS Setup Utility to reconfigure system time, then reboot system. System board Previous boot incomplete - Default configuration used Run “Load Default Settings” in BIOS Setup Utility.
Error Message List No beep Error Messages FRU/Action in Sequence No beep, power-on indicator turns off and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 111.. Ensure every connector is connected tightly and correctly. Reconnect the DIMM. LED board. System board. No beep, power-on indicator turns on and LCD is blank. Power source (battery pack and power adapter). See “Power System Check” on page 111..
Phoenix BIOS Beep Codes Code Beeps Verify Real Mode 03h Disable Non-Maskable Interrupt (NMI) 04h Get CPU type 06h Initialize system hardware 08h Initialize chipset with initial POST values 09h Set IN POST flag 0Ah Initialize CPU registers 0Bh Enable CPU cache 0Ch Initialize caches to initial POST values 0Eh Initialize I/O component 0Fh Initialize the local bus IDE 10h Initialize Power Management 11h Load alternate registers with initial POST values 12h Restore CPU control word du
Code Beeps POST Routine Description 3Ch Advanced configuration of chipset registers 3Dh Load alternate registers with CMOS values 42h Initialize interrupt vectors 45h POST device initialization 46h 2-1-2-3 Check ROM copyright notice 48h Check video configuration against CMOS 49h Initialize PCI bus and devices 4Ah Initialize all video adapters in system 4Bh QuietBoot start (optional) 4Ch Shadow video BIOS ROM 4Eh Display BIOS copyright notice 50h Display CPU type and speed 51h In
Code POST Routine Description Detect and install external RS232 ports 83h Configure non-MCD IDE controllers 84h Detect and install external parallel ports 85h Initialize PC-compatible PnP ISA devices 86h Re-initialize onboard I/O ports 87h Configure Motherboard Configurable Devices (optional) 88h Initialize BIOS Area 89h Enable Non-Maskable Interrupts (NMIs) 8Ah Initialize Extended BIOS Data Area 8Bh Test and initialize PS/2 mouse 8Ch Initialize floppy controller 8Fh Determine number
Code Beeps POST Routine Description B9h Prepare Boot BAh Initialize DMI parameters BBh Initialize PnP Option ROMs BCh Clear parity checkers BDh Display MultiBoot menu BEh Clear screen (optional) BFh Check virus and backup reminders C0h Try to boot with INT 19 C1h Initialize POST Error Manager (PEM) C2h Initialize error logging C3h Initialize error display function C4h Initialize system error handler C5h PnPnd dual CMOS (optional) C6h Initialize notebook docking (optional) C7h
Code 122 Beeps F5h Boot to Mini DOS F6h Clear Huge Segment F7h Boot to Full DOS Chapter 4
Index of Symptom-to-FRU Error Message LCD-Related Symptoms Symptom / Error Action in Sequence LCD backlight doesn't work LCD is too dark LCD brightness cannot be adjusted LCD contrast cannot be adjusted Enter BIOS Utility to execute “Load Setup Default Settings”, then reboot system. Reconnect the LCD connectors. Keyboard (if contrast and brightness function key doesn't work).
Power-Related Symptoms Symptom / Error Action in Sequence The system doesn’t power-off. Power source (battery pack and power adapter). See “Power System Check” on page 111. Hold and press the power switch for more than 4 seconds. System board Battery can’t be charged See “Check the Battery Pack” on page 113. Battery pack System board PCMCIA-Related Symptoms Symptom / Error Action in Sequence System cannot detect the PC Card (PCMCIA) PCMCIA slot assembly System board PCMCIA slot pin is damaged.
Power Management-Related Symptoms Symptom / Error Action in Sequence The system doesn't resume from hibernation mode. See “Save to Disk (S4)” on page 41. Hard disk connection board Hard disk drive System board The system doesn't resume from standby mode after opening the LCD. See “Save to Disk (S4)” on page 41. LCD cover switch System board Battery fuel gauge in Windows doesn’t go higher than 90%. Remove battery pack and let it cool for 2 hours.
Keyboard/Touchpad-Related Symptoms Symptom / Error Touchpad does not work. Action in Sequence Reconnect touchpad cable. Touchpad board System board Modem-Related Symptoms Symptom / Error Internal modem does not work correctly. Action in Sequence Modem phone port modem combo board System board NOTE: If you cannot find a symptom or an error in this list and the problem remains, see “Undetermined Problems” on page 129.
Intermittent Problems Intermittent system hang problems can be caused by a variety of reasons that have nothing to do with a hardware defect, such as: cosmic radiation, electrostatic discharge, or software errors. FRU replacement should be considered only when a recurring problem exists. When analyzing an intermittent problem, do the following: 1. Run the advanced diagnostic test for the system board in loop mode at least 10 times. 2. If no error is detected, do not replace any FRU. 3.
Undetermined Problems The diagnostic problems does not identify which adapter or device failed, which installed devices are incorrect, whether a short circuit is suspected, or whether the system is inoperative. Follow these procedures to isolate the failing FRU (do not isolate non-defective FRU). NOTE: Verify that all attached devices are supported by the computer. NOTE: Verify that the power supply being used at the time of the failure is operating correctly. (See “Power System Check” on page 111.
Chapter 4 129
130 Chapter 4
Chapter 5 Jumper and Connector Locations Top and Bottom View Chapter 5 131
Clearing Password Check and BIOS Recovery This section provide you the standard operating procedures of clearing password and BIOS recovery for Ferrari 1100. Ferrari 1100 provide one Hardware Open Gap on main board for clearing password check, and one Hotkey for enabling BIOS Recovery.
• If there is no Password request, BIOS Password is cleared. Otherwise, please follow the steps and try again. NOTE: The steps are only for clearing BIOS Password ( Supervisor Password and User Password ).
BIOS Recovery by Crisis Disk BIOS Recovery Boot Block: BIOS Recovery Boot Block is a special block of BIOS. It is used to boot up the system with minimum BIOS initialization. Users can enable this feature to restore the BIOS firmware to a successful one once the previous BIOS flashing process failed. BIOS Recovery Hotkey: The system provides a function hotkey: Fn+Esc, for enable BIOS Recovery process when system is powered on during BIOS POST.
Chapter 6 FRU (Field Replaceable Unit) List This chapter gives you the FRU (Field Replaceable Unit) listing in global configurations of Ferrari 1200. Refer to this chapter whenever ordering for parts to repair or for RMA (Return Merchandise Authorization). Please note that WHEN ORDERING FRU PARTS, you should check the most up-to-date information available on your regional web or channel. For whatever reasons a part number change is made, it will not be noted on the printed Service Guide.
Ferrari 1200 Exploded Diagram 136 Chapter 6
Ferrari 1200 FRU List Category No. Part Name and description ACER PART NO. Adapter ADAPTER DELTA 65W 19V 1.7X5.5X11 YELLOW SADP-65KB DFJ LED LF AP.06501.022 ADAPTER LITE-ON 65W 1.7X5.5X11 PA1650-02AC LF LEVEL 4 AP.06503.016 ADAPTER LITE-ON 65W 19V 1.7X5.5X11 YELLOW PA-1650-02AC LV4 (FOR FLICKER ISSUE) LED LF AP.06503.023 ADAPTER HIPRO 65W 19V 1.7X5.5X11 YELLOW HP-OK065B13 LV4 (FOR FLICKER ISSUE) LED LF AP.0650A.011 ADAPTER 65W 3PIN DELTA SADP-65KB BFJA LF LEVEL-4 FOR OBL ONLY AP.06501.
Category No. Part Name and description ACER PART NO. TOUCHPAD SYNAPTICS TM-01059-004 56.FR901.001 BLUETOOTH BOARD FOXCONN BCM2045 V2 T60H928.11 BT.21100.005 VOIP PHONE FOR FERRARI7 LC.VIP00.016 MINI WLAN/B FOXCONN 802.11BGN ATHEROS XB63 BG T60H976.00 FW:V06 MINICARD NI.23600.007 WIRELESS LAN BOARD 802.11BG XB63 ATHEROS MINICARD QMI EM105 NI.23600.028 WIRELESS LAN BOARD 802.11BGN FOXCONN BCM4312 T77H030.00 MINICARD NI.23600.029 WIRELESS LAN BOARD 802.11BGN FOXCONN T77H053.
Category No. Part Name and description ACER PART NO. POWER CORD 10A 3PIN BK DENMARK 27.01518.561 POWER CORD 10A 250V 3PIN DENMARK BK 27.01518.671 POWER CORD 10A 250V 3PIN BK SOUTH AFRICA 27.01518.571 POWER CORD 16A 250V SOUTH AFRICA BK 27.01518.681 POWER CORD 10A 250V SWISS 27.01518.581 POWER CORD 10A 250V 3PIN SWISS BK 27.01518.691 POWER CORD 10A 250V 3PIN ITALY 27.01518.611 POWER CORD 10A 250V 3PIN ITALY BK 27.01518.711 POWER CORD 2.5A 250V AUSTRALIA 27.01518.
Category 140 No. Part Name and description ACER PART NO. FINGERPRINT BOARD BRACKET 33.FR901.002 CARDREADER BRACKET 33.FR901.003 HINGE COVER LEFT 42.FR901.003 HINGE COVER RIGHT 42.FR901.004 FINGERPRINT PAD COVER 42.FR901.005 DUMMY NEW CARD FOR FERRARI7 42.FR901.006 UNITLOAD COVER 42.FRA01.001 SD DUMMY CARD 42.TKJ01.
Category No. Part Name and description ACER PART NO. LOWER CASE W/MODEM&DC-IN CABLE&SPEAKER 60.FRA01.001 UPPER CASE W/FINGER PRINT HOLE 60.FRA01.002 MIDDLE COVER 42.FR901.001 SPEAKER 23.FRA01.001 CPU AMD TURIONX2 RM70 PGA 2.0G 1M 638 35W GRIFFIN B1 KC.TRM02.70K CPU AMD TURIONX2 ZM80 PGA 2.1G 2M 638 35W GRIFFIN B1 KC.TZM02.800 CPU AMD TURIONX2 ZM82 PGA 2.2G 2M 638 35W GRIFFIN B1 KC.TZM02.820 CPU AMD TURIONX2 ZM84 PGA 2.3G 2M 638 35W GRIFFIN B1 KC.TZM02.840 CPU AMD TURIONX2 ZM86 PGA 2.
Category No. Part Name and description ACER PART NO. ASSEMBLY SUPLER MULTI SLOT-IN MODULE 8X 6M.FRA01.001 OPTICAL BRACKET SUPPORT 33.FR901.005 OPTICAL BRACKET 33.FRA01.001 DVD SUPER MULTI DRIVE 8X 9.5MM SLOT-IN PANASONIC UJ867 LF W/O BEZEL SATA KU.00807.063 HDD HOLDER 42.FRA01.002 HDD 160GB 5400RPM SATA WD SEAGATE ST9160827AS F/W:2.ALA KH.16001.029 HDD 160GB 5400RPM SATA HGST HTS543216L9A300 F/W:C30C KH.16007.019 HDD 160GB 5400RPM SATA WD WD1600BEVT-22ZCT0 FW:11.01A11 KH.16008.
Category No. Part Name and description ACER PART NO. HDD 320GB 5400RPM SATA WD WD3200BEVT-22ZCT0 ML125 F/ W:01.01A01 KH.32008.013 CPU HEATSINK WITH FAN 60.FRA01.003 UPPER CASE THERMAL PIPE 60.FRA01.004 KEYBOARD 12KB-FV1 84KS BLACK US KB.INT00.171 KEYBOARD 12KB-FV1 84KS BLACK HEBREW KB.INT00.172 KEYBOARD 12KB-FV1 85KS BLACK UK KB.INT00.173 KEYBOARD 12KB-FV1 85KS BLACK TURKISH KB.INT00.174 KEYBOARD 12KB-FV1 84KS BLACK THAILAND KB.INT00.175 KEYBOARD 12KB-FV1 85KS BLACK SWISS KB.INT00.
Category No. Part Name and description ACER PART NO. KEYBOARD 12KB-FV1 88KS BLACK JAPANESE KB.INT00.188 KEYBOARD 12KB-FV1 85KS BLACK ITALIAN KB.INT00.189 KEYBOARD 12KB-FV1 84KS BLACK ISRAEL KB.INT00.190 KEYBOARD 12KB-FV1 85KS BLACK HUNGARIAN KB.INT00.192 KEYBOARD 12KB-FV1 84KS BLACK GREEK KB.INT00.193 KEYBOARD 12KB-FV1 85KS BLACK GERMAN KB.INT00.194 KEYBOARD 12KB-FV1 85KS BLACK FRENCH KB.INT00.195 KEYBOARD 12KB-FV1 85KS BLACK DANISH KB.INT00.198 KEYBOARD 12KB-FV1 85KS BLACK CZECH KB.
Category No. Part Name and description ACER PART NO. LCD/CAMERA CABLE 12.1" 50.FRA01.001 CAMERA 0.3M SUYIN CN0314-SN30OV03-1 57.TQ901.001 CAMERA 0.3M CHICONY CNF701721004971L 57.TQ901.002 LCD COVER 1 2.1" W/LOGO&ANTENNA 60.FR901.005 LCD BEZEL 12.1" W/CAMERA HOLE & MIC 60.FRA01.005 LED LCD AUO 12.1" WXGA GLARE B121EW09 V0 LF 220NIT 16MS LK.12105.014 MAINBOARD FERRARI_7_GT ATI RS780 LF W/RTC BATTERY & MODEM BOARD MB.FRA01.001 SODIMM 1GB DDRII667 NANYA NT1GT64U8HB0BN-3C LF (0.09U) KN.1GB03.
Category No. Part Name and description ACER PART NO. SODIMM 2GB DDRII667 MICRON MT16HTF25664HY-667E1 KN.2GB04.001 SODIMM 2GB DDRII667 SAMSUNG M470T5663QZ3-CE6 LF KN.2GB0B.003 SODIMM 2GB DDRII667 HYNIX HYMP125S64CP8-Y5 LF KN.2GB0G.004 RUBBER FOOT FRONT RIGHT FOR FERRARI7 47.FR901.001 RUBBER FOOT FRONT LEFT FOR FERRARI7 47.FR901.002 RUBBER FOOT BACK RIGHT FOR FERRARI7 47.FR901.003 MISCELLANEOUS LCD SCREW RUBBER RIGHT 47.FR901.008 LCD SCREW RUBBER LEFT 47.FR901.
Chapter 6 147
Appendix A Model Definition and Configuration Ferrari 1200 Series Appendix A 148
Appendix B Test Compatible Components This computer’s compatibility is tested and verified by Acer’s internal testing department. All of its system functions are tested under Windows® XP Home, Windows® XP Pro environment. Refer to the following lists for components, adapter cards, and peripherals which have passed these tests. Regarding configuration, combination and test procedures, please refer to the Ferrari 1200 series Compatibility Test Report released by the Acer Mobile System Testing Department.
Microsoft® Windows® Vista Environment Test Item Specification CRT Port Test CRT Monitor Acer 211c 21”, ViewSonic G220F, ViewSonic PF790 19” LCD Monitor Acer FP751 17” TFT LCD, Acer AL1521, Acer AL1721, ViewSonic VD201b, Westinghouse W37G, HP LP2065, HP S9500 Projector Dell 3300MP USB Port Test USB Keyboard/Mouse Microsoft Natural Keyboard Pro Dell USB Keyboard Logicool USB Mouse (OWCM-USB) Logitech USB Wheel Mouse Logitech First Wheel Mouse Dell Dell by Logitech Dell Internet Navigator Keyboard Del
Item Specification PCMCIA Test LAN/Modem Card TDK CardBus Ethernet 10/100 32-Bit CBE-10/100BTX Storage Card Hitachi Microdrive 4G 1394 Card Buffalo 1394 Interface Cardbus (IFC-ILCB/DV) USB2.0 Card IBM EtherJet CardBus Adapter 10/100 Wireless Lan Card Cisco Wireless LAN Card 802.11a (Not recommended for wireless ready model) NETGEAR Wireless LAN card 802.
152 Appendix B
Appendix C Online Support Information This section describes online technical support services available to help you repair your Acer Systems. If you are a distributor, dealer, ASP or TPM, please refer your technical queries to your local Acer branch office. Acer Branch Offices and Regional Business Units may access our website. However some information sources will require a user i.d. and password. These can be obtained directly from Acer CSD Taiwan.
154 Appendix C
Index A hotkeys AFLASH Utility Antennas Audio 16 E 51 102 Error Symptom-to-Spare Part Index 36 Euro 110 17 External CD-ROM Drive Check 106 B Battery Pack BIOS External Module Disassembly 60 package 32 password control ROM size 32 ROM type 32 vendor 32 Version 32 F 32 BIOS Supports protocol Features 1 Fingerprint Board 51 fpc cable 99 32 FRU (Field Replaceable Unit) List 39–51 Navigating 40 Hard disk 34 Hard Disk Drive Module Board Layout HDD 125 64 34 Hibernation mode brightn
LCD Brackets 101 System Check Procedures System Memory 32 LCD Module Disassembly Flowchart 95 LCD with the Brackets System Utilities 39 98 T lower cover 61 Test Compatible Components M Top Main Unit Disassembly Flowchart 161 125 Touch Pad Board 66 82 touchpad 85 Mainboard hotkey media access 16 109 Troubleshooting 105 Touchpad Check 11 Memory Check 107 Model Definition 138 Modem Board 90 on indicator U Undetermined Problems 124 utility N BIOS Notebook Manager 39–51 V 16 ho