Brief Overview/Resumen breve/ Aperçu rapide Accessories – M2Smart®SE Accesorios – M2Smart®SE Accessoires – M2Smart®SE Version/ Versión: 1.02 M2Smart®SE_Set_Brief Overview_V1.
U.S. Edition 2021/EE. UU. Edición 2021/Édition français 2021 © Copyright ACD Group All Rights Reserved This document may not be duplicated or made accessible to third parties without written permission by ACD. Todos los derechos reservados Este documento no se puede reproducir ni facilitar a terceros sin consentimiento por escrito de ACD. Tous droits réservés Ce document ne peut pas être dupliqué ou rendu accessible àtiers sans l'autorisation écrite d'ACD. M2Smart®SE_Set_Brief Overview_V1.
Table of Contents/Índice/Table des matières English 1 Introduction .................................................................................................. 4 2 Transportation and Storage .......................................................................... 6 3 Scope of Delivery ......................................................................................... 6 4 Commissioning and Operation of M2Modules .............................................. 6 4.1 M2Modules ....................
Français 9 Mise en service et fonctionnement des M2Modules ................................... 32 9.1 M2UHF-RFID Shortrange ....................................................................................... 32 9.1.1 Exposition aux RF .............................................................................................. 32 9.2 M2UHF-RFID Midrange .......................................................................................... 32 9.2.1 Exposition aux RF .................................
Figure 3: DS2Smart® Charging and transmission box Figure 4: DS2Smart® Charging box Figure 5: DS2Smart® Developer box Figure 6: DSBattery 2-fold Figure 7: M2Grip5 Figure 8: M2 logistics protective caps Figure 9: Replacement Battery M2Smart®SE_Set_Brief Overview_V1.
2 Transportation and Storage ATTENTION The rechargeable battery for the Mobile Handheld Computer is a lithium ion rechargeable battery pack. Lithium ion rechargeable batteries can explode if they are subjected to fire or heat. The rechargeable battery pack may not be taken apart and subjected to fire or heat (greater than 60 °C/140 °F). Do not set the Mobile Handheld Computer, battery, docking station or power supply near heat sources (heater blowers, etc.
ATTENTION Do not set the modules near heat sources (heater blowers, etc.) and never subject them to direct solar radiation, excess quantities of dust or shocks. Make sure that there is no stumbling hazard due to connection cable or power supplies. The modules may not be used in areas subject to explosion. ATTENTION ATTENTION Before using the modules, any connection cables must be checked for damage. Damaged parts must be replaced. For this, please contact ACD Elektronik GmbH.
4.1.3 Attaching and removing the modules The upper plug-in module and the lower plug-in module can be attached and removed as shown in the following figures. Figure 10: Attaching and removing the upper plug-in module Figure 11: Attaching and removing the lower plug-in module When attaching and removing the modules, please do not reach into the area of the plug-in sliding mechanism, as there is a risk of injury due to jamming during sliding.
4.2 M2UHF-RFID Shortrange The M2UHF-RFID Shortrange is described below. It is a plug-in module for reading UHF-RFID tags, which can be used for the upper plug-in sliding mechanism. Figure 12: M2UHF-RFID Shortrange 4.2.1 Security Advices The M2UHF-RFID Shortrange is designt for occupational use only.
4.2.2 Handling After the M2UHF-RFID Shortrange attachable module has been plugged into the main device on the upper plug-slide mechanism, it can be used for reading UHF-RFID tags. To do this, start a software application to initialize the module. Then the read process can be carried out with the software application. Figure 13: M2UHF-RFID Shortrange Antenna and Radiation The red box represents where the antenna is palced and the red lines indicate the radiation of HF signal.
4.2.3 Technical Data M2UHF-RFID Shortrange The table below includes the technical data for the M2UHF-RFID Shortrange plug-in module. Technical Data Housing Protection class Operating temperature Storage temperature Rel. humidity Device dimensions Weight Interfaces Frequency range EU Frequency range USA and Canada Read range Antenna type RFID protocols Output power 4.2.4 ABS/PC IP54 -20 °C to 50 °C/-4 °F to 122 °F Condensation of the device must be avoided.
M2UHF-RFID Midrange The M2UHF-RFID Midrange is described below. It is a plug-in module for reading UHF-RFID tags, which can be used for the upper plug-in sliding mechanism. Figure 14: M2UHF-RFID Midrange 4.2.7 Security Advices The M2UHF-RFID Midrange is designt for occupational use only. ATTENTION ATTENTION Removal of the plug-in module on the upper plug-slide mechanism of the device: Please do not reach into the area around the scanner glass; there is a risk of injury due to pinching when sliding.
4.2.8 Handling After the M2UHF-RFID Midrange attachable module has been plugged into the main device on the upper plug-slide mechanism, it can be used for reading UHF-RFID tags. To do this, start a software application to initialize the module. Then the read process can be carried out with the software application. Figure 15: M2UHF-RFID Shortrange Antenna and Radiation The red box represents where the antenna is palced and the red lines indicate the radiation of HF signal. .
4.2.9 Technical Data M2UHF-RFID Midrange The table below includes the technical data for the M2UHF-RFID Midrange plug-in module. Technical Data Housing Protection class Operating temperature Storage temperature Rel. humidity Device dimensions Weight Interfaces Frequency range EU Frequency range USA and Canada Read range Antenna type RFID protocols Output power EU Output power USA and Canada ABS/PC IP54 -20 °C to 50 °C/-4 °F to 122 °F Condensation of the device must be avoided.
Commissioning and Operation of Accessories 4.3 4.3.1 Docking station DS2Smart® Charging and transmission box, DS2Smart® Charging box and DS2Smart® Developer box Security Advices ATTENTION ATTENTION Only ACD original power supplies and rechargeable batteries approved by ACD may be used for the operation of the Mobile Handheld Computer and docking station! The use of components that have not been approved can cause the destruction of the backhand scanner or docking station.
Place the docking station correctly on a smooth and clean underground, which is not exposed to direct sunlight. ATTENTION ATTENTION The charging and communication contacts are very sensitive! The Mobile Handheld Computer and the replacement rechargeable battery may only be inserted in and removed from the docking station as described above. Do not touch the contact with your fingers or with objects such as pens, screwdrivers, etc.
Place the docking station correctly on a smooth and clean underground, which is not exposed to direct sunlight. ATTENTION ATTENTION The charging and communication contacts are very sensitive! The Mobile Handheld Computer and the replacement rechargeable battery may only be inserted in and removed from the docking station as described above. Do not touch the contact with your fingers or with objects such as pens, screwdrivers, etc.
4.3.5 Disposal of the DS2Smart® All components should be disposed of properly at the end of their technical lifetime. ATTENTION 4.4 4.4.1 Docking station DS2Battery 2-fold Security Advices ATTENTION ATTENTION Only ACD original power supplies and rechargeable batteries approved by ACD may be used for the operation of the Mobile Handheld Computer and docking station! The use of components that have not been approved can cause the destruction of the backhand scanner or docking station.
4.4.2 Inserting the replacement rechargeable battery in and removing it from the docking station To insert the replacement rechargeable battery in the device, tip it diagonally downward and place it in the rechargeable battery compartment. Insert the rechargeable battery so that the contacts are aligned with the contacts of the docking station. Press the rechargeable battery into the rechargeable battery compartment until it snaps in audibly.
4.4.3 Status LEDs The status LEDs of the DS2Battery docking station will be described below. Figure 22: Status LEDs of the DS2Battery Charging cradle for replacement rechargeable battery CHARGE LED lit red: Replacement battery is being charged CHARGE LED lit green: Replacement battery is fully charged CHARGE LED not lit: There is no replacement battery inserted in the docking station ® The charging time of a battery of the M2Smart SE is approx. 4.5 hours at room temperature. 4.4.
4.5 M2Grip5 ® ® A handle is available as an accessory for the M2Smart SE. It can be attached to the M2Smart SE without tools. Figure 23: M2Grip5 The upper and lower slide mechanisms remain untouched and can therefore still be used for different ® ® M2Modules. It is still possible to charge the M2Smart SE with M2Grip5 in the DS2Smart . ® ® Please note that the M2Grip5 is suitable for the M2Smart SE without scanner and for the M2Smart SE with 2D shortrange scanner (SE4770). 4.5.
4.5.3 Removing M2Grip5 from the M2Smart®SE To remove the M2Grip5, slide the side sections of the M2Grip5 off the device. Then you can guide the M2Grip5 out of the upper retaining strap attachment. Figure 25: Removing M2Grip5 from M2Smart®SE (1/2) Figure 26: Removing M2Grip5 from M2Smart®SE (2/2) After the M2Grip5 is removed, the retaining strap can be attached again. M2Smart®SE_Set_Brief Overview_V1.
4.6 M2 logistics protective caps ® M2 logistics protective caps are another accessory for the M2Smart SE. Their purpose is to increase fall protection. M2 logistics protective caps are designed for the upper and lower blind cap. Figure 27: M2 logistics protective caps ® ® To charge the M2Smart SE in the DS2Smart , the M2 logistics protective caps must be removed. 4.6.1 Security Advices Unintended use of the M2Grifp5 should be avoided. ATTENTION 4.6.
Figure 29: Attaching the lower logistics protective cap 4.6.3 Removing M2 logistics protective caps from the M2Smart®SE ® To remove the upper and lower M2 logistics protective caps from the M2Smart SE, remove them from the blind caps. Figure 30: Removing the upper logistics protective cap First loosen the retaining strap, then remove the lower logistics protective cap and reinsert the retaining strap. M2Smart®SE_Set_Brief Overview_V1.
Figure 31: Removing the lower logistics protective cap M2Smart®SE_Set_Brief Overview_V1.
4.7 4.7.1 Replacement Battery Security Advices ATTENTION ATTENTION ATTENTION The rechargeable battery for the Mobile Handheld Computer is a lithium ion rechargeable battery pack. Lithium ion rechargeable batteries can explode if they are subjected to fire or heat. The rechargeable battery pack may not be taken apart and subjected to fire or heat (greater than 60 °C/140 °F).
To insert the rechargeable battery in the device, tip it diagonally downward and place it in the rechargeable battery compartment. Insert the rechargeable battery so that the contacts are aligned with the contacts of the device. Then the rechargeable battery can be folded downward so that the lock snaps in. Then the hand strap can be hooked back in. Figure 33: Inserting the rechargeable battery M2Smart®SE_Set_Brief Overview_V1.
5 Instructions for Cleaning and Care Clean the module by setting it down on a surface (e.g. table). This way, you can hold it securely and the module cannot slip out of your hands during the cleaning process. ATTENTION Do not use any corrosive chemicals, cleaning solutions or strong cleaning agents in order to clean the Mobile Handheld Computer, battery and docking station. All components must be disposed of properly at the end of their technical lifetime.
6 Support If you need additional assistance, please contact our support hotline: ///ACD Elektronik GmbH Engelberg 2 88480 Achstetten, Germany Tel.: +49 7392 708-488 E-mail: support.technik@acd-elektronik.de Web: https://www.acd-gruppe.de/en/ The support hotline is available for you Monday to Thursday from 8:00 am to 5:00 pm (CET) and Friday from 8:00 am to 3:00 pm (CET).
8 Manufacturer’s Representations and Warranties ACD Elektronik GmbH Engelberg 2 88480 Achstetten Germany Phone: +49 7392 708-0 Fax: +49 7392 708-190 These Representations and Warranties are applicable to all customers (the “Customers” and each, individually, a “Customer”) purchasing products (the “Products”) manufactured by ACD Elektronik GmbH (the “Company”). 1. Warranty and Limitations: 1.
1.9 All requests and notices under this Warranty shall be directed to: ACD Elektronik GmbH Engelberg 2 88480 Achstetten Germany Phone: +49 7392 708-0 Email: info@acd-elektronik.de 1.10. THE WARRANTY SET FORTH IN SECTION 1.1 IS MADE IN LIEU OF ALL OTHER WARRANTIES (WHETHER EXPRESS OR IMPLIED), RIGHTS OR CONDITIONS, AND CUSTOMER ACKNOWLEDGES THAT EXCEPT FOR SUCH LIMITED WARRANTY, THE PRODUCTS ARE PROVIDED “AS IS.
9 Mise en service et fonctionnement des M2Modules L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : L’appareil ne doit pas produire de brouillage; L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement. 9.1 9.1.
