USER GUIDE WIMAX 802.
USER GUIDE RG300 WiMAX IEEE 802.16e Indoor Gateway with 3.5 and 3.7 GHz Frequency Band Support, Up to Two LAN (RJ-45) Ports, One VoIP (RJ-11) Port, and 802.
COMPLIANCES FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
COMPLIANCES EC CONFORMANCE DECLARATION Marking by the above symbol indicates compliance with the Essential Requirements of the R&TTE Directive of the European Union (1999/5/EC). This equipment meets the following conformance standards: ◆ EN 60950-1 (IEC/UL 60950-1) - Product Safety ◆ EN 302 326, EN 300 328, EN 301 489-1/-4/-17 - EMC requirements for radio equipment This device is intended for use in all European Community countries.
ABOUT THIS GUIDE PURPOSE This guide details the hardware features of the RG300 WiMAX 802.16e Indoor Gateway, including its physical and performance-related characteristics, and how to install the device and use its configuration software. AUDIENCE This guide is for PC users with a working knowledge of computers. You should be familiar with Windows operating system concepts.
ABOUT THIS GUIDE SEPTEMBER 2011 REVISION This is the first revision of this guide. This guide is valid for software version 1.1.0.6.
CONTENTS SECTION I COMPLIANCES 3 ABOUT THIS GUIDE 5 CONTENTS 7 FIGURES 11 TABLES 13 GETTING STARTED 14 1 INTRODUCTION 15 RG300 Hardware Description 16 Wi-Fi Option 16 Power Status LED 17 Wi-Fi Status LED 17 WiMAX Signal LEDs 18 LAN Ports 18 VoIP Phone Port 19 Power Adapter Socket 19 Reset Button 19 2 INSTALLING THE RG300 20 Package Checklist 20 Installation Overview 20 Select a Location 20 Cable Connections 21 3 INITIAL CONFIGURATION 23 Accessing the Web Managem
CONTENTS SECTION II Common Web Page Buttons 28 WEB CONFIGURATION 29 4 SYSTEM SETTINGS 30 System Status 31 Administrator Settings 32 Firmware Upgrade 33 Configuration Tools 34 System Time 35 System Log 36 Reset 37 5 WAN CONFIGURATION 38 WAN Settings 39 Dynamic IP Address 40 Static IP Settings 40 L2TP Settings 41 PPTP Settings 41 DNS 42 DDNS 43 6 LAN CONFIGURATION 44 LAN Settings 45 DHCP Client List 46 7 NAT CONFIGURATION 47 NAT Settings 48 Port Mapping 48 DMZ
CONTENTS Host Filtering 55 9 ROUTING CONFIGURATION Routing Table 58 Static Route 59 10 UPNP CONFIGURATION 60 UPnP 61 11 VOIP SETTINGS 62 Connection Type 63 SIP Account 63 SIP Settings 65 Speed Dial 66 Dial Plan 66 Call Feature 68 Phone Settings 70 Codecs 71 12 WI-FI SETTINGS 73 Basic Wireless Settings 74 Advanced Wireless Settings 76 Wireless Security 77 Wired Equivalent Privacy (WEP) 78 WPA Pre-Shared Key 79 ACL Settings 81 13 QOS CONFIGURATION 82 QoS Settings
CONTENTS Cannot Connect to the Internet 89 Cannot Access Web Management 90 Forgot or Lost the Password 90 Resetting the Unit 90 B HARDWARE SPECIFICATIONS 91 Physical Specifications 91 WiMAX Specifications 92 VoIP Specifications 92 Wi-Fi Specifications 93 Compliances 94 C CABLES AND PINOUTS 95 Twisted-Pair Cable Assignments 95 10/100BASE-TX Pin Assignments 95 Straight-Through Wiring 96 Crossover Wiring 97 RJ-11 Port 98 GLOSSARY 99 INDEX 104 – 10 –
FIGURES Figure 1: Front of the RG300 16 Figure 2: RG300 LED Indicators 17 Figure 3: Back of the RG300 18 Figure 4: RG300 Connections 21 Figure 5: Login Page 23 Figure 6: Home Page 24 Figure 7: WiMAX Account Login 25 Figure 8: Confirm Settings 26 Figure 9: Setup Wizard Finished 26 Figure 10: Advanced Setup 27 Figure 11: Common Web Page Buttons 28 Figure 12: System Status – Internet 31 Figure 13: System Status – Gateway 31 Figure 14: System Status – TR069 32 Figure 15: System Stat
FIGURES Figure 32: NAT Settings 48 Figure 33: Port Mapping 48 Figure 34: DMZ Settings 49 Figure 35: ALG Settings 50 Figure 36: Firewall Settings 52 Figure 37: Client Filtering Settings 52 Figure 38: Port Filtering 53 Figure 39: MAC Filtering 54 Figure 40: URL Filtering 55 Figure 41: Host Filtering 55 Figure 42: Routing Table 58 Figure 43: Static Route 59 Figure 44: UPnP Setting 61 Figure 45: Connection Type 63 Figure 46: SIP Account Settings 63 Figure 47: SIP Settings 65 Fig
TABLES Table 1: Power Status LED 17 Table 2: Wi-Fi Status LED 17 Table 3: WiMAX Signal Status LEDs 18 Table 4: LAN Port Status LED 19 Table 5: Dial Plan Elements 67 Table 6: Troubleshooting Chart 89 Table 7: 10/100BASE-TX MDI and MDI-X Port Pinouts 96 Table 8: RJ-11 Port Pinout 98 – 13 –
SECTION I GETTING STARTED This section provides an overview of the RG300, and describes how to install and mount the unit. It also describes the basic settings required to access the management interface and run the setup Wizard.
1 INTRODUCTION The RG300 WiMAX 802.16e Indoor Gateway is a WiMAX subscriber station designed to provide Internet access for a home or small office. The unit provides a gateway function between a WiMAX service provider and a local Ethernet LAN. The device enables a service provider to deliver last mile broadband wireless access as an alternative to wired DSL or cable modems. The RG300 includes up to two RJ-45 Ethernet ports for LAN connections and one RJ-11 Voice over IP (VoIP) phone port.
CHAPTER 1 | Introduction RG300 Hardware Description RG300 HARDWARE DESCRIPTION The front of the RG300 provides an array of system status indicators. The back includes two LAN ports for 10/100 Mbps Ethernet connections, one RJ-11 VoIP phone port, and a DC power jack. Figure 1: Front of the RG300 WI-FI OPTION The RG300 includes an 802.11b/g/n Wi-Fi support. This unit includes internal antennas for local wireless connections to PCs.
CHAPTER 1 | Introduction RG300 Hardware Description POWER STATUS LED The RG300 includes a Power LED indicator that simplifies installation and WiMAX network troubleshooting. The LED, which is located on the front panel, is described in the following table. Figure 2: RG300 LED Indicators Power Status LED Wi-Fi Status LED WiMAX Signal LEDs Table 1: Power Status LED Status Description On Green The unit has completed entry to a WiMAX network.
CHAPTER 1 | Introduction RG300 Hardware Description WIMAX SIGNAL LEDS The RG300 includes seven WiMAX signal strength LED indicators that display the current WiMAX receive signal status. The LEDs, which are located on the front panel, are described in the following table. Table 3: WiMAX Signal Status LEDs LED Status Description 1 On Blue Indicates the receive signal is 5 dB or more. 2 On Blue Indicates the receive signal is 8 dB or more. 3 On Blue Indicates the receive signal is 12 dB or more.
CHAPTER 1 | Introduction RG300 Hardware Description The RJ-45 ports include a built-in LED status indicator. This LED indicator is described in the following table. Table 4: LAN Port Status LED LED Status Description Link/Activity On Green Ethernet port has a valid link with an attached device. Flashing Green The port is transmitting or receiving data. Off Ethernet port has no link with another device.
2 INSTALLING THE RG300 This section describes how to install and connect the RG300 WiMAX 802.16e Indoor Gateway. PACKAGE CHECKLIST The RG300 package includes: ◆ RG300 unit ◆ RJ-45 Category 5 network cable ◆ AC power adapter ◆ Quick Installation Guide ◆ User Guide CD INSTALLATION OVERVIEW Before installing the RG300, verify that you have all the items listed in the package checklist above. If any of the items are missing or damaged, contact your local dealer.
CHAPTER 2 | Installing the RG300 Cable Connections ◆ The device should be accessible for network cabling and allow the status LED indicators to be clearly visible. NOTE: If the RG300 displays a weak WiMAX receive signal, try moving it to another location. CABLE CONNECTIONS The RG300 is a plug-and-play device, so once it has been connected to your PC and powered up, it is fully operable.
CHAPTER 2 | Installing the RG300 Cable Connections 3. Connect Category 5 or better Ethernet cables from the RG300’s LAN ports to the network ports of your PCs. Alternatively, you can connect the LAN port to an Ethernet switch or other device. Make sure the length of each cable does not exceed 100 meters (328 ft). If a PC is powered on, the RJ-45 LAN port LED on the RG300 will turn on to indicate a valid link. 4.
3 INITIAL CONFIGURATION The RG300 initial configuration steps can be made through its web management interface using the Setup Wizard. It is recommended to make the initial changes by connecting a PC directly to one of the RG300’s LAN ports. ACCESSING THE WEB MANAGEMENT INTERFACE The RG300 has a default IP address of 192.168.1.1 and a subnet mask of 255.255.255.0.
CHAPTER 3 | Initial Configuration Accessing the Web Management Interface Language – Selects English or Traditional Chinese as the web interface language. NOTE: It is recommended that you configure a user password as the first step under “Administrator Settings” on page 32 to control management access to the unit. HOME PAGE The home page displays the current status of the WiMAX connection. To configure basic settings for the current operating mode, click Basic Setup.
CHAPTER 3 | Initial Configuration Using the Basic Setup Wizard ◆ Signal Strength (RSSI) – The current signal strength value of the received WiMAX radio signal. ◆ Signal Quality (CINR) – An indication of the carrier-to-interferenceplus-noise-ratio (CINR), which measures the strength of the receive signal compared to other interference and noise. ◆ Connection Status – The current status of the WiMAX connection. ◆ Central Frequency – The center frequency of the WiMAX signal.
CHAPTER 3 | Initial Configuration Using the Basic Setup Wizard ■ Preview – Displays the current user account that will be used. ■ Password – The user password required for authentication as provided by the WiMAX operator. 2. Apply Settings – Click “Confirm” to apply the basic settings. Figure 8: Confirm Settings 3. Basic Setup Finished – When the Basic Setup steps are completed the unit reboots and attempts to connect to the specified WiMAX network. Log in again to return to the Home page.
CHAPTER 3 | Initial Configuration The Advanced Setup Menu THE ADVANCED SETUP MENU The Advanced Setup menu provides access to all the configuration settings available for the RG300. Figure 10: Advanced Setup Each primary menu item is sumarized below with links to the relevant section in this guide where configuration parameters are described in detail: ◆ System – Configures general device settings. See page 30. ◆ WAN – Configures WAN settings. See page 39. ◆ LAN – Configures LAN settings. See page 44.
CHAPTER 3 | Initial Configuration Common Web Page Buttons COMMON WEB PAGE BUTTONS The web management interface includes some common buttons that are displayed at the top of each page. Figure 11: Common Web Page Buttons The list below describes these common buttons: ◆ Apply — Applies all new configuration changes on the current page and saves them to memory. ◆ Home — Returns to the web management home page. ◆ Logout — Immediately closes the current web management session.
SECTION II WEB CONFIGURATION This section provides details on configuring the RG300 using the web browser interface.
4 SYSTEM SETTINGS The RG300’s System menu allows you to perform general management functions for the unit, including setting the system time, configuring an access password, and upgrading the system software.
CHAPTER 4 | System Settings System Status SYSTEM STATUS The system status page displays connectivity status information for the unit’s WiMAX (WAN) and LAN interfaces, and the number of clients connected to the network. Figure 12: System Status – Internet Internet – Displays WAN (WiMAX) connection status: ◆ WAN IP – Displays the IP address assigned by the service provider. ◆ Subnet Mask – Displays the WAN subnet mask assigned by the service provider.
CHAPTER 4 | System Settings Administrator Settings Figure 14: System Status – TR069 TR069 Status – Displays the type of the TR069 connection:: ◆ Connected Type – Displays the TR069 connection type. Figure 15: System Status – Information Information – Displays the number of connected clients, as well as the unit’s LAN and WAN MAC addresses: ◆ Connected Clients – Displays the number of connected clients, if any. ◆ LAN MAC Address – Displays the LAN MAC address.
CHAPTER 4 | System Settings Firmware Upgrade ◆ Current Password – You need to first enter your current administrator password to be able to configure a new one. (Default: admin) NOTE: If your RG300 unit is not configured with the standard default login Username/Password, use the default values on the label affixed to the unit. ◆ New Password – Enter a new administrator password. (Range: 3~12 characters) ◆ Confirm New Password – Enter the new password again for verification.
CHAPTER 4 | System Settings Configuration Tools ■ Start Time – Sets the auto upgrade start time. ■ End TIme – Sets the auto upgrade end time. ■ Update Interval – A time interval (in seconds) for checking the Info URL for new software information. ■ Limit Rate – Places a limit on the firmware download rate from the server. ■ Info URL – A text string that indicates the location of an Auto Upgrade information file on an FTP server.
CHAPTER 4 | System Settings System Time Figure 19: Restore Configuration Settings SYSTEM TIME The RG300 uses the Simple Network Time Protocol (SNTP) to set its internal clock based on periodic updates from a time server. Maintaining an accurate time on the device enables the system log to record meaningful dates and times for event entries. SNTP uses Coordinated Universal Time (or UTC, formerly Greenwich Mean Time, or GMT) based on the time at the Earth’s prime meridian, zero degrees longitude.
CHAPTER 4 | System Settings System Log ◆ Sync with host – Sets the unit’s time from the web management PC’s system time. ◆ Current Date (yyyy:mm:dd) – The current date of the system clock. ◆ New Date (yyyy:mm:dd) – Sets the system clock date. ◆ Set Time Zone – SNTP uses Coordinated Universal Time (or UTC, formerly Greenwich Mean Time, or GMT) based on the time at the Earth’s prime meridian, zero degrees longitude.
CHAPTER 4 | System Settings Reset by specifying a minimum severity level. Error message levels range from the most severe (Emergency) to least severe (Debug). The message levels that are logged include the specified minimum level up to the Emergency level. ◆ Max Size — The maximum memory size to be used for log messages on the Gateway. (Range: 1-512 KB) ◆ Set — Click to set the Max Size and System Log Level values. RESET The Reset page allows you to restart the device’s software.
5 WAN CONFIGURATION The information in this chapter covers the configuration options for the RG300’s WAN connection.
CHAPTER 5 | WAN Configuration WAN Settings WAN SETTINGS Select the WAN connection type used by your service provider and specify DNS (Domain Name System) servers. Figure 23: WAN Settings The unit can be connected to your ISP in one of the following ways: ◆ NONE – No IP Address assigned. ◆ DHCP IP Address – Selects configuration for an Internet connection using DHCP for IP address assignment. ◆ Static IP Address – Selects configuration for an Internet connection using a fixed IP assignment.
CHAPTER 5 | WAN Configuration WAN Settings ◆ PPTP – Selects configuration for an Internet connection using the Point-to-Point Tunneling Protocol, an access protocol often used for virtual private networks. NOTE: For the Dynamic IP Address (DHCP) option, the unit requires no further configuration. Selecting other WAN types displays the parameters that are required for configuring the connection.
CHAPTER 5 | WAN Configuration WAN Settings ◆ Netmask – Indicates the subnet mask, such as 255.255.255.0. ◆ Gateway – The gateway IP address provided by your service provider. ◆ Configured DSCP (Differentiated Services Code Point) – Sets the default DSCP priority for all egress packets not classified by other rules. L2TP SETTINGS If your service provider supports Layer 2 Tunneling Protocol (L2TP) for your Internet connection, configure the settings described below.
CHAPTER 5 | WAN Configuration DNS ◆ Server IP – The IP address of the PPTP server, as specified by the service provider. ◆ Username – Enter your user name for connecting to the PPTP service, as supplied by the service provider. (Range: 1-20 characters) ◆ Password – Specify the password for your PPTP connection, as supplied by the service provider.
CHAPTER 5 | WAN Configuration DDNS DDNS Dynamic DNS (DDNS) provides users on the Internet with a method to tie a specific domain name to the unit’s dynamically assigned IP address. DDNS allows your domain name to follow your IP address automatically by changing your DNS records when your IP address changes. The RG300 provides access to a number DDNS service providers, such as DynDns.org, Easydns.com, and ZoneEdit.com. To set up an DDNS account, visit the website of one of the supported service providers.
6 LAN CONFIGURATION The information in this chapter covers the configuration options for the RG300’s LAN functions.
CHAPTER 6 | LAN Configuration LAN Settings LAN SETTINGS The RG300 must have a valid IP address for management using a web browser and to support other features. The unit has a standard default IP address of 192.168.1.1. You can use this IP address or assign another address that is compatible with your existing local network. The unit can also be enabled as a Dynamic Host Configuration Protocol (DHCP) server to allocate IP addresses to local PCs.
CHAPTER 6 | LAN Configuration DHCP Client List ◆ Lease Time – Selects a time limit for the use of an IP address form the IP pool. When the time limit expires, the client has to request a new IP address. (Options: 1hr, 3hr, 6hr, 8hr, 12hr, 1 day, 3 days, 1 week) ◆ Static Leases – Maps IP addresses to PC MAC addresses so that the CPE always assigns the same IP to specific computers on the LAN. ■ MAC Address – The unique MAC address of a computer in the LAN.
7 NAT CONFIGURATION The information in this chapter covers the configuration options for the RG300’s Network Address Translation (NAT) functions.
CHAPTER 7 | NAT Configuration NAT Settings NAT SETTINGS Network Address Translation (NAT) is a standard method of mapping multiple “internal” IP addresses to one “external” IP address on devices at the edge of a network. For the RG300, the internal (local) IP addresses are the IP addresses assigned to local PCs by the DHCP server, and the external IP address is the IP address assigned to the WiMAX interface.
CHAPTER 7 | NAT Configuration DMZ The following parameters are displayed on this page: ◆ Private IP – The IP address of the server on the local Ethernet network. The specified address must be in the same subnet as the RG300 and its DHCP server address pool. Alternatively, the IP address can be set by selecting a PC from the DHCP client list. ◆ Use Client List – Allows the Private IP to be selected from the DHCP client list.
CHAPTER 7 | NAT Configuration ALG NOTE: Adding a host to the DMZ may expose your local network to a variety of security risks, so only use this option as a last resort. ALG The RG300 supports the passthrough of three of the most commonly used VPN protocols; PPTP, L2TP, and IPsec, as well as VoIP SIP traffic. The VPN protocols allow remote users to establish a secure connection to their corporate network.
8 FIREWALL CONFIGURATION The information in this chapter covers the configuration options for the RG300’s firewall functions.
CHAPTER 8 | Firewall Configuration Firewall Settings FIREWALL SETTINGS The RG300 provides extensive firewall protection by restricting connection parameters to limit the risk of intrusion and defending against a wide array of common hacker attacks. You can also block access to the Internet from clients on the local network based on IP addresses and TCP/UDP port numbers, or specific MAC addresses.
CHAPTER 8 | Firewall Configuration Port Filtering The following parameters are displayed on this page: ◆ Target IP – Specifies an IP address or range on the local network to filter. ◆ Destination Port Range – Specifies a TCP/UDP port number range to filter. (Range: 1-65535 or Any) ◆ Protocol – Specifies the the port type. (Options: TCP, UDP, Any) ◆ Add – Adds a new IP address to the filter table. ◆ Remove – Removes an IP address from the filter table.
CHAPTER 8 | Firewall Configuration MAC Filtering ◆ Port Number — Specifies a custom-defined range of TCP/UDP ports to block. ◆ Schedule to Block — Configures the days of the week and times to block the defined traffic. MAC FILTERING You can block access to the Internet from clients on the local network based on MAC addresses. You can configure up to 20 MAC address filters on the unit.
CHAPTER 8 | Firewall Configuration URL Filtering URL FILTERING The RG300 provides a method for blocking Internet access based on Uniform Resource Locator (URL) keywords. By filtering URLs accessed from the network, users can be prevented from reaching prohibited online content. Figure 40: URL Filtering The following items are displayed on this page: ◆ String — Specifies text keyword contained in URLs that will be filtered. (Maximum 256 characters; invalid characters [‘ “ & ' # \].
CHAPTER 8 | Firewall Configuration Host Filtering ◆ Add — Enters a domain name keyword for a host filtering. For example, myhost.example.com. ◆ Remove — Removes an entry from the filter table.
9 ROUTING CONFIGURATION The information in this chapter covers the configuration options for the RG300’s Routing functions.
CHAPTER 9 | Routing Configuration Routing Table ROUTING TABLE The Routing Table displays the list of static routes on the unit. Figure 42: Routing Table The following parameters are displayed in this section on this page: ◆ Route – The IP address that identifies the IP subnet of the remote network. ◆ Gateway – The IP address of the router within the local IP subnet that forwards traffic to the remote IP subnet. ◆ Netmask – The mask that identifies the IP subnet of the remote network.
CHAPTER 9 | Routing Configuration Static Route STATIC ROUTE Static routes allow a manual method to set up routing between specific destination networks, subnetworks, or hosts. Static routes may be required to force the use of a specific route to a subnet. Static routes do not automatically change in response to changes in network topology, so only configure a small number of stable routes to ensure network accessibility.
10 UPNP CONFIGURATION The information in this chapter covers the configuration options for the RG300’s Universal Plug and Play Forum (UPnP) feature.
CHAPTER 10 | UPnP Configuration UPnP UPNP UPnP (Universal Plug and Play Forum) provides inter-connectivity between devices supported by the same standard. Figure 44: UPnP Setting The following parameters are displayed in this section on this page: ◆ UPnP – Enables UpnP support on the unit. ◆ NAT-PMP (NAT Port Mapping Protocol) – Allows a computer in a private network (behind a NAT router) to automatically configure the router to allow parties outside the private network to contact it.
11 VOIP SETTINGS Voice over Internet Protocol (VoIP) technology is a way of using the Internet to make phone calls. Phone calls can be tranmitted over the Internet by encoding a voice call into data packets at one end and then decoding it back into voice calls at the other end. This encoding and decoding is from a analog signal (your voice) into a digital signal (data packets) and then back into an analog signal.
CHAPTER 11 | VoIP Settings Connection Type CONNECTION TYPE The VoIP Connection Type page defines which CPE IP address to use when connecting with the service provider's VoIP service. Figure 45: Connection Type The following parameters are displayed on this page: ◆ WAN — Uses the same IP address as currently configured for the WAN interface. ◆ Static IP Address — Sets a static IP address to connect to the VoIP service.
CHAPTER 11 | VoIP Settings SIP Account The following parameters are displayed on this page: ◆ Proxy Enable — When enabled, forwards SIP messages to a SIP proxy instead of a SIP domain. ◆ Enable — Enables the VoIP ports on the Gateway. ◆ Telephone Number — The phone number that is assigned to this phone line. ◆ The same with Telephone Number — Uses the specified Telephone Number as the Outgoing Display Name. ◆ Outgoing Display Name — The name that is displayed to the other party during a call.
CHAPTER 11 | VoIP Settings SIP Settings SIP SETTINGS The SIP Setting page allows you to configure RTP, DTMF, and FAX settings. Figure 47: SIP Settings The following items are displayed on this page: ◆ RTP Port — The Real-time Transport Protocol (RTP) and Real-time Control Protocol (RTCP) do not use specified port numbers. You can specify a port base that the RTP and RTCP traffic can use.
CHAPTER 11 | VoIP Settings Speed Dial SPEED DIAL The Speed Dial page allows you to configure up to eight VoIP numbers that are immediately dialed when a user enters the Speed Dial Key sequence (as defined on the Dial Plan page) followed by a speed dial number. Figure 48: Speed Dial DIAL PLAN Dial-plan strings specify key sequences used for specific calling features (Transfer, New Call, 3-way conference), as well as defining call restriction filters.
CHAPTER 11 | VoIP Settings Dial Plan Figure 49: Dial Plan Settings The function of elements allowed in a dial plan are described in the table below: Table 5: Dial Plan Elements Element Example Description x xxxx Represents a digit of any value ( 0 to 9) that can be dialed on a phone. This example has a rule with four digits of any number. . xx. Indicates zero or more occurrences of the previous symbol.
CHAPTER 11 | VoIP Settings Call Feature CALL FEATURE The RG300 allows you to configure several call features, such as call waiting and call-forwarding. Other call features can be implemented by pressing specific phone buttons or entering dial patterns. NOTE: Some call features may be dependent on support at the SIP server. Check with the SIP service provider. Figure 50: Call Features The following items are displayed on this page: ◆ Call Waiting — Enables a call waiting alert.
CHAPTER 11 | VoIP Settings Call Feature ◆ ■ Early Transfer — During a call press the “Flash” button, which puts the caller on hold, then enter the new call key sequence (as defined on the Dial Plan page; default “**”). You can then dial the transfer number. When you hear the transfer number ringtone, enter the transfer key sequence (as defined on the Dial Plan page; default “*#”) and then hang up.
CHAPTER 11 | VoIP Settings Phone Settings PHONE SETTINGS The Phone Settings page allows you to configure control features that affect a phone connected to a VoIP port. Figure 51: Phone Settings The following items are displayed on this page: ◆ Caller ID Block — Check this box to enable a block on the displayed ID of incoming calls. ◆ Echo Cancellation — Enables a time delay for voice echo cancellation.
CHAPTER 11 | VoIP Settings Codecs CODECS A codec (coder/decoder) is the way a voice analog signal is converted into a digital bitstream to send over the network, and how it is converted back into an analog signal at the receiving end. Codecs differ in the type of data compression that is used to save network bandwidth and in the time delay caused in the signal. This results in different voice quality experienced by the user.
CHAPTER 11 | VoIP Settings Codecs ◆ Priority List — The Gateway automatically negotiates the codec to use for each called party. You can specify a priority for the codecs that you prefer to use. Select a codec in the list, then use the UP and DOWN buttons to set the priority. The Gateway attempts to use the codec highest in the list before trying the next lower one.
12 WI-FI SETTINGS The RG300 includes an IEEE 802.11n radio interface for local Wi-Fi communications. The Wi-Fi set up pages include configuration options for the radio signal characteristics and Wi-Fi security.
CHAPTER 12 | Wi-Fi Settings Basic Wireless Settings BASIC WIRELESS SETTINGS From the WiFi menu, click on Basic to configure basic settings for the unit’s Wi-Fi radio interface. The unit’s radio can operate in six modes, IEEE 802.11b/g mixed, 802.11b only, 802.11g only, 802.11n only, 802.11g/n mixed, and 802.11b/g/n mixed. Note that IEEE 802.11g is backward compatible with 802.11b, and 802.11n is backward compatible with 802.11b/g at slower data transmit rates.
CHAPTER 12 | Wi-Fi Settings Basic Wireless Settings ■ 11b/g/n Mixed: All 802.11b/g/n clients can communicate with the Wi-Fi radio (up to 150 Mbps), but data transmission rates may be slowed to compensate for 802.11b/g clients. ◆ SSID — The name of the wireless network service provided by the WiFi radio. Clients that want to connect to the network must set their SSID to the same as that of the Wi-Fi radio.
CHAPTER 12 | Wi-Fi Settings Advanced Wireless Settings ADVANCED WIRELESS SETTINGS The Advanced Settings page includes additional parameters concerning the wireless network and Wi-Fi Multimedia settings. Figure 54: Advanced Wireless Settings The following items are displayed on this page: ◆ Beacon Period — The rate at which beacon signals are transmitted from the access point. The beacon signals allow wireless clients to maintain contact with the access point.
CHAPTER 12 | Wi-Fi Settings Wireless Security frames to a receiving station to negotiate the sending of a data frame. After receiving an RTS frame, the station sends a CTS (clear to send) frame to notify the sending station that it can start sending data. If the RTS threshold is set to 0, the access point always sends RTS signals. If set to 2347, the access point never sends RTS signals.
CHAPTER 12 | Wi-Fi Settings Wireless Security Figure 55: Security Mode Options The supported security mechanisms and their configuration parameters are described in the following sections: ◆ OPEN, SHARED — See “Wired Equivalent Privacy (WEP)” on page 79. ◆ WPAPSK, WPA2PSK, WPAPSK/WPA2PSK mixed mode — See “WPA Pre-Shared Key” on page 80.
CHAPTER 12 | Wi-Fi Settings Wireless Security ◆ Encrypt Type — Selects WEP for data encryption (OPEN mode only). ◆ Default ID — Selects the WEP key number to use for authentication or data encryption. If wireless clients have all four WEP keys configured to the same values, you can change the encryption key to any of the settings without having to update the client keys. (Range: 1~4) ◆ Key 1~4 Type — Sets WEP key type as ASCII or hexadecimal. ◆ Key 1~4 String — Sets WEP key values.
CHAPTER 12 | Wi-Fi Settings Wireless Security ■ ◆ ◆ WPAPSK/WPA2PSK mixed mode — Clients using WPA or WPA2 with a Pre-shared Key are accepted for authentication. The default data encryption type is TKIP/AES. EncryptType — Selects the data encryption type to use. (Default is determined by the Security Mode selected.) ■ TKIP — Uses Temporal Key Integrity Protocol (TKIP) keys for encryption. WPA specifies TKIP as the data encryption method to replace WEP.
CHAPTER 12 | Wi-Fi Settings ACL Settings ACL SETTINGS Wireless clients can be authenticated for network access by checking their MAC address against a local database configured on the RG300. You can configure a list of up to 32 wireless client MAC addresses in the filter list to allow network access. Figure 58: ACL Settings The following items are displayed on this page: ◆ Enable — Enables the ACL feature. ◆ MAC Address — Physical address of a client.
13 QOS CONFIGURATION The RG300 supports Quality of Service (QoS) settings that enable traffic rate limits to be set for all or specific LAN clients.
CHAPTER 13 | QoS Configuration QoS Settings QOS SETTINGS From the QoS Settings page, you can set rate limits for outbound (WiMAX uplink) traffic from all or specified clients. Figure 59: QoS Settings The following parameters are displayed on this page: ◆ ◆ General — Sets QoS parameters that apply to all LAN clients (except those listed in the QoS Rules table): ■ Enable — Enables the QoS settings on the Gateway.
14 VLAN SETTINGS The VLAN configuration pages include the following options: ◆ “VLAN Settings” on page 84 – 84 –
CHAPTER 14 | VLAN Settings VLAN Settings VLAN SETTINGS From the VLAN Settings page, you can assign ports to a VLAN group. When a device connects to the network, it automatically assumes the VLAN of the port. If the user changes ports and needs access to the same VLAN, the user must manually make a port-to-VLAN assignment for the new connection. Figure 60: VLAN Settings The following parameters are displayed on this page: ◆ Enable — Enables the VLAN settings on the Gateway.
15 TUNNEL SETTINGS The Tunnel configuration pages include the following options: ◆ “Tunnel Settings” on page 87 – 86 –
CHAPTER 15 | Tunnel Settings Tunnel Settings TUNNEL SETTINGS The Tunnel Settings page allows to set up a Generic Routing Encapsulation (GRE) tunnel between the CPE and another network. The GRE tunnel enables routing protocols and other non-IP traffic to be routed between networks. Figure 61: Tunnel Settings The following parameters are displayed on this page: ◆ ◆ General — ■ Enable — Enables the GRE tunnel on the CPE. ■ Tunnel IP Address — A private IP assigned to the CPE's GRE tunnel interface.
SECTION III APPENDICES This section provides additional information and includes these items: ◆ “Troubleshooting” on page 89 ◆ “Hardware Specifications” on page 91 ◆ “Cables and Pinouts” on page 95 – 88 –
A TROUBLESHOOTING DIAGNOSING LED INDICATORS Table 6: Troubleshooting Chart Symptom Action Power LED is Off ◆ AC power adapter may be disconnected. Check connections between the unit, the AC power adapter, and the wall outlet. Power LED is Red ◆ The unit has detected a system error. Reboot the unit to try and clear the condition. ◆ If the condition does not clear, contact your local dealer for assistance. ◆ ◆ Move the location of the unit.
APPENDIX A | Troubleshooting Cannot Access Web Management CANNOT ACCESS WEB MANAGEMENT If the management interface cannot be accessed using a web browser: ◆ Be sure the management station is correctly configured for TCP/IP. The IP settings should be set to “obtain an IP address automatically.” ◆ Try a Ping command from the management station to the unit’s IP address to verify that the entire network path between the two devices is functioning correctly.
B HARDWARE SPECIFICATIONS PHYSICAL SPECIFICATIONS PORTS 1~2 LAN ports, 10/100BASE-TX with auto-negotiation, RJ-45 connector 1 FXS port, RJ-11 connector NETWORK INTERFACE RJ-45 connector, auto MDI/X: 10BASE-T: RJ-45 (100-ohm, UTP cable; Category 3 or better) 100BASE-TX: RJ-45 (100-ohm, UTP cable; Category 5 or better) LED INDICATORS System: Power, WiMAX signal strength, WiFi, Ports: Link/Activity AC POWER ADAPTER Input: 100-240 VAC, 50-60 Hz, 0.
APPENDIX B | Hardware Specifications WiMAX Specifications WIMAX SPECIFICATIONS ANTENNAS Pattern: Monopole Antenna (Omnidirectional) Transmit and Receive: One transmit and two receive with Maximal-Ratio Combining (MRC). Support for transmitter diversity. 3.5 GHz Gain: 6 dBi 3.7 GHz Gain: 9.9 dBi Impedance: 50 Ohm OPERATING FREQUENCY 3.5 GHz: 3300-3600 MHz CE-3.7 GHz: 3600-3750 MHz FCC-3.7 GHz: 3650-3700 MHz CHANNEL BANDWIDTH 3.5 GHz model: 5 and 10 MHz 3.
APPENDIX B | Hardware Specifications Wi-Fi Specifications Echo cancellation Adaptive jitter buffer, up to 200 milliseconds DTMF tone detection and generation CALL FEATURES Caller ID number and name Caller ID Block Call transfer Call waiting/hold/retrieve 3-way conference call Call blocking T.38 fax relay Dial plan Speed dial Call forwarding: No Answer/Busy/All REN (RING EQUIVALENT 3 REN total in system NUMBER) WI-FI SPECIFICATIONS MAXIMUM 802.
APPENDIX B | Hardware Specifications Compliances COMPLIANCES EMISSIONS FCC CFR 47 Part 15 Class B EN 55022 Class B EMMUNITY EN 55024 Class B EN 301 489-1/4/17 WIMAX RADIO SIGNAL US: 3.65-3.7 GHz - FCC Part 90Z CERTIFICATION CE: 3.3-3.6 GHz - EN 302 326 WI-FI RADIO SIGNAL FCC CFR 47 Part 15 Subpart C CERTIFICATION EN 300 328 SAFETY IEC/UL 60950-1 STANDARDS IEEE 802.16e-2005 WAVE 1 and WAVE 2 IEEE 802.3-2005 10BASE-T and 100BASE-TX IEEE 802.11b, 802.11g, and 802.
C CABLES AND PINOUTS TWISTED-PAIR CABLE ASSIGNMENTS For 10/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. Each wire pair is identified by two different colors. For example, one wire might be green and the other, green with white stripes. Also, an RJ-45 connector must be attached to both ends of the cable. CAUTION: Each wire pair must be attached to the RJ-45 connectors in a specific orientation.
APPENDIX C | Cables and Pinouts Twisted-Pair Cable Assignments Table 7: 10/100BASE-TX MDI and MDI-X Port Pinouts PIN MDI Signal Namea MDI-X Signal Name 1 Transmit Data plus (TD+) Receive Data plus (RD+) 2 Transmit Data minus (TD-) Receive Data minus (RD-) 3 Receive Data plus (RD+) Transmit Data plus (TD+) 6 Receive Data minus (RD-) Transmit Data minus (TD-) 4, 5, 7, 8 Not used Not used a. The “+” and “-” signs represent the polarity of the wires that make up each wire pair.
APPENDIX C | Cables and Pinouts Twisted-Pair Cable Assignments CROSSOVER WIRING If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neither port is labeled with an “X” (MDI), a crossover must be implemented in the wiring.
APPENDIX C | Cables and Pinouts RJ-11 Port RJ-11 PORT Standard telephone RJ-11 connectors and cabling can be found in several common wiring patterns. These six-pin connectors can accommodate up to three wire pairs (three telephone lines), but usually only one or two pairs of conductor pins and wires are implemented. The RJ-11 port on this device contains only one wire pair on the inner pins (3 and 4).
GLOSSARY 10BASE-T IEEE 802.3-2005 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable. 100BASE-TX IEEE 802.3-2005 specification for 100 Mbps Fast Ethernet over two pairs of Category 5 or better UTP cable. ACCESS POINT An Wi-Fi internetworking device that seamlessly connects wired and wireless networks. AUTHENTICATION The process to verify the identity of a client requesting network access.
GLOSSARY operator depending on performance requirements, operating preferences, and regulatory constraints. CPE Customer-Premises Equipment. Terminal equipment provided by a service provider that is located at a subscriber’s premises and supports a communication channel between a customer and the service provider. DNS Domain Name System. A system used for translating host names for network nodes into IP addresses. DHCP Dynamic Host Configuration Protocol.
GLOSSARY IEEE 802.16E The WiMAX standard that provides mobile broadband wireless access using Scalable Orthogonal Frequency Division Multiple Access (SOFDMA). IP ADDRESS The Internet Protocol (IP) address is a numerical identification assigned to a device that communicates in a network using the Internet Protocol. ISP Internet Service Provider. A company that offers an access service that connects customers to the Internet. LED Light emitting diode. Used for indicating a device or network condition.
GLOSSARY SSID Service Set Identifier. A name that is sent in packets over a Wi-Fi network, which functions as a password for clients connecting to the network. The SSID differentiates one Wi-Fi network from another. SNTP Simple Network Time Protocol. SNTP allows a device to set its internal clock based on periodic updates from a Network Time Protocol (NTP) server. Updates can be requested from a specific NTP server, or can be received via broadcasts sent by NTP servers. SIM Subscriber Identity Module.
GLOSSARY server. WPA provides a simple operating mode that uses just a pre-shared password for network access. WIMAX The IEEE 802.16 standard for Worldwide Interoperability for Microwave Access. The IEEE 802.16-2004 standard, known as “fixed WiMAX,” supports only point-to-point links and has no support for mobility. The IEEE 802.16e-2005 standard, known as “mobile WiMAX,” is an amendment to IEEE 802.16-2004 and supports mobility.
INDEX A F AC power adapter 19 administrator password, setting 32 administrator settings 32 Advanced Setup Menu 27 AES encryption 80 authentication type 77 authentication options 78 auto-logout time 33 factory defaults, restoring 34 firewall protection 52 firmware update 33 fixed-IP xDSL 39 fragmentation threshold 76 frequency setting 75 B beacon interval 76 button, Reset 19 C cable assignments 95 cable connections 21 channel setting 75 channels, maximum 93 checklist 20 client filter, enable 53 Codec 7
INDEX O W open system 77 operating frequency 93 WAN connection type 31 web management interface access 23 login 23 troubleshooting 90 WEP security 78 wireless network mode 74 Wizard, setup 25 WPA pre-shared key 79 P package checklist 20 panels, front and rear 16 password, setting 32 phone settings 70 ping discard 52 port indicators 17, 18 power socket 19 power supply, specifications PPTP 40, 50 private IP 49 private port 49 proxy server port 64 91 R radio mode 74 rear panel sockets 19 reboot unit 37,
RG300 E082012-AP-R02 149100000170W