User's Manual

ManualsBrandsAccton Technology ManualsComputers & AccessoriesDraft 11n Dual band Wireless Access Point

Table Of Contents

Compliances
About This Guide
Contents
Figures
Tables
Index of CLI Commands
Getting Started
Introduction
- Key Hardware Features
- Description of Capabilities
- Package Contents
- Hardware Description
Network Topologies
- Interference Issues
- Infrastructure Wireless LAN
- Infrastructure Wireless LAN for Roaming Wireless PCs
- Infrastructure Wireless Bridge
Installing the access point
- Location Selection
- Mounting on a Horizontal Surface
- Mounting on a Wall
- Connecting and Powering On
Initial Configuration
- Connecting to the Login Page
- Home Page and Main Menu
- Common Web Page Buttons
- Quick Start
- Main Menu Items
Web Configuration
System Settings
- Administration Settings
- IP Address
- Radius Settings
  - Primary and Secondary RADIUS Server Setup
  - RADIUS Accounting
- System Time
- SpectraLink Voice Priority
- VLAN Configuration
- System Logs
- Quick Start Wizard
Management Settings
- Remote Management Settings
- Access Limitation
- Simple Network Management Protocol
Advanced Settings
- Local Bridge Filter
- Link Layer Discovery Protocol
- Access Control Lists
Wireless Settings
- Spanning Tree Protocol (STP)
- Authentication
  - Local Authentication
  - RADIUS MAC Authentication
- Interface Mode
- Radio Settings
- Virtual Access Points (VAPs)
- QoS
Maintenance Settings
- Upgrading Firmware
- Running Configuration
- Resetting the Access Point
Status Information
- AP Status
  - AP System Configuration
  - AP Wireless Configuration
- Station Status
- System Logs
Command Line Interface
- Using the Command Line Interface
  - Console Connection
  - Telnet Connection
  - Entering Commands
- General Commands
- System Management Commands
  - System Management Commands
- System Logging Commands
- System Clock Commands
- DHCP Relay Commands
- SNMP Commands
- Flash/File Commands
- RADIUS Client Commands
- 802.1X Authentication Commands
- MAC Address Authentication Commands
- Filtering Commands
- Spanning Tree Commands
- WDS Bridge Commands
- Ethernet Interface Commands
- Wireless Interface Commands
- Wireless Security Commands
- Link Layer Discovery Commands
- VLAN Commands
- WMM Commands
Appendices
Troubleshooting
- Diagnosing LED Indicators
- Before Contacting Technical Support
Hardware Specifications
Cables and Pinouts
- Twisted-Pair Cable Assignments
- 10/100BASE-TX Pin Assignments
- Straight-Through Wiring
- Crossover Wiring
- 1000BASE-T Pin Assignments
  - Cable Testing for Existing Category 5 Cable
  - Adjusting Existing Category 5 Cabling to Run 1000BASE-T
- Console Port Pin Assignments
Glossary
Index

HAPTER

| Management Settings

Simple Network Management Protocol

– 71 –

affect. Clicking ‘OK’ returns to the home page. Changes will not be

saved upon a reboot unless the running configuration file is saved.

VIEW ACCESS

CONTROL MODEL

To configure SNMPv3 management access to the AP, follow these steps:

1. Specify read and write access views for the AP MIB tree.

2. Configure SNMP user groups with the required security model (that is,

SNMP v1, v2c, or v3) and security level (authentication and privacy).

3. Assign SNMP users to groups, along with their specific authentication

and privacy passwords.

Figure 32: SNMP VACM

CREATING VIEWS

SNMPv3 views are used to restrict user access to specified portions of the

MIB tree. The are no predefined views by default.

The following items are displayed on the VACM page.

◆ View Name – The name of the SNMP view. (Range: 1-32 characters)

◆ Type – Indicates if the object identifier of a branch within the MIB tree

is included or excluded from the SNMP view.

◆ OID – Allows you to configure the object identifiers of branches within

the MIB tree. Wild cards can be used to mask a specific portion of the

OID string.