CONTROLLER 76 WALL HANG SMART AC OUTLET USER MANUAL
WELCOME Thank you for choosing AC Infinity. We are committed to product quality and friendly customer service. If you have any questions or suggestions, please don’t hesitate to contact us. Visit www.acinfinity.com and click contact for our contact information. EMAIL WEB LOCATION support@acinfinity.com www.acinfinity.
MANUAL CODE CTR682008X1 4 PRODUCT MODEL UPC-A CONTROLLER 76 CTR76A 819137021525
MANUAL INDEX Manual Index ................................................................................. Page 5 Key Features ................................................................................. Page 6 Product Contents ........................................................................... Page 7 Powering and Setup........................................................................ Page 8 Programming .................................................................................
KEY FEATURES ACTIVE MONITORING SENSOR PROBE Features automation controls that power electronics based on temperature, humidity, timers, and schedules. LED display shows key data like outlet power status, temperature, humidity, trends, clock, and countdowns. The corded probe is constructed of stainless steel to ensure precise temperature and humidity readings.
PRODUCT CONTENTS WALL HANG CONTROLLER (x1) WALL-HANG WOOD SCREWS (x2) SENSOR PROBE (x1) WIRE TIE (x1) CABLE TIE MOUNT (x1) 7
POWERING AND SETUP STEP 1 Locate the connector plug of the sensor probe and plug it into the sensor port at the bottom side of the controller. STEP 2 Position the corded sensor probe and secure it by using the wire tie and cable tie mount if needed.
POWERING AND SETUP STEP 3 Locate a spot free on obstruction and secure the anchor into your wall. Twist the wood screw into the anchor. STEP 4 Hang the device on the screw using the hole on the backside of the controller.
POWERING AND SETUP STEP 5 Plug the controller’s power plug into an AC power outlet to power the controller. STEP 6 Plug your device (not included) into one of the two sockets to power your device with the controller.
PROGRAMMING 7 TIMER TO 8 ON 5 6 9 TO ON PM 11 4 1 10 2 3 1. MODE BUTTON Cycles through each of the controller’s mode: OFF, ON, AUTO (4 triggers), TIMER TO ON, TIMER TO OFF, CYCLE (On and Off), and SCHEDULE (On and Off). 2. UP / DOWN BUTTON Adjusts the parameters of the mode that you are in. In most modes, the up button increases and down button decreases the setting. Holding both buttons simultaneously sets the parameters to off. 3.
PROGRAMMING 5. PROBE TEMPERATURE Current temperature that the probe is detecting. Displays “--“ if no probe is plugged in. Includes a trend indicator that signals a rise, fall or no change in temperature within the last hour. 6. PROBE HUMIDITY Current humidity that the probe is detecting. Displays “--“ if no probe is plugged in. Includes a trend indicator that signals a rise, fall or no change in humidity within the last hour. 7. CONTROLLER MODE Displays the mode that the controller is currently in.
PROGRAMMING CONTROLLER MODES Pressing the mode button will cycle through the controller’s available programming modes: OFF, ON, AUTO (4 triggers), TIMER TO ON, TIMER TO OFF, CYCLE (On and Off), and SCHEDULE (On and Off). OFF MODE Your device will be off regardless of temperature, humidity, or time-based triggers. OFF You can jump back to OFF Mode any time by holding the mode button while in other modes or settings.
PROGRAMMING AUTO MODE (HIGH TEMPERATURE TRIGGER) Pressing the up or down button sets the high temperature trigger. Your device will turn on if the probe’s reading meets or exceeds this threshold. If the probe’s reading falls below this trigger point, your device will be turned off. This turn-off point can be adjusted using the buffer setting as shown on page 21.
PROGRAMMING AUTO MODE (HIGH HUMIDITY TRIGGER) Pressing the up or down button sets the high humidity trigger. Your device will turn on if the probe’s reading meets or exceeds this threshold. If the probe’s reading falls below this trigger point, your device will be turned off. This turn-off point can be adjusted using the buffer setting as shown on page 21.
PROGRAMMING TIMER TO ON MODE In this mode, press the up or down button to set a countdown time. During the countdown, your device will be set to OFF. Once the countdown ends, your device will trigger to turn ON. The countdown will begin if no buttons are pressed for 5 seconds. The time left on the countdown is shown on the lower right corner of the display above the setting. Leaving the timer mode while the countdown is running will pause it until you return to this mode.
PROGRAMMING CYCLE MODE (ON AND OFF) In this mode, set an ON duration and an OFF duration for your device to cycle through continuously. Press the up or down button to first set a duration for your device to be on and then press the mode button again, to set a duration for device to be Off. The countdown will begin if no buttons are pressed for 5 seconds. Press the up or down button to set a countdown for your device to turn on.
PROGRAMMING SCHEDULE MODE (ON AND OFF) In this mode, set an ON clock-time and an OFF clock-time schedule for your device to follow through daily. Press the up or down button to set a clock time for your device to turn on. Then press the mode button and use the up or down button to set a clock time for your device to turn off. Refer to page 20 to learn how to set the controller’s clock time. The countdown will begin if no buttons are pressed for 5 seconds.
PROGRAMMING CONTROLLER SETTINGS Pressing the setting button will cycle through the controller’s available settings: DISPLAY, F/C, CLOCK, CALIBRATION TEMPERATURE, CALIBRATION HUMIDITY, BUFFER TEMPERATURE, and BUFFER HUMIDITY. DISPLAY SETTING This setting adjusts the brightness of the display. Press the up or down button to cycle through 1, 2, 3, A2, and A3. The highest brightness setting is 3 while the lowest brightness is 1.
PROGRAMMING CLOCK CLOCK SETTING This setting adjusts the current clock time. Press the up or down button to increase or decrease the time. Every cycle past 12:00 will switch the time between AM and PM. The current clock time will be shown at the lower left corner of the display. PM PM CALIB. CALIBRATION TEMPERATURE SETTING This setting adjusts the temperature reading that the sensor probe is measuring. Press the up or down button to increase or decrease the data figure by 2°F (or 1°C) increments.
PROGRAMMING BUFFER TEMPERATURE SETTING The buffer used in the auto mode temperature trigger can be adjusted to prevent the device from turning on and off too quickly due to changing conditions in your environment. BUFF.T° In high temperature triggers, your device will turn on, only turning off when the measured temperature falls below the set temperature by the buffer number you have set here.
PROGRAMMING ALERT ICONS On the top left of the display is the alert icon section. Icons may flash when the controller wishes to alert you that a particular function or alarm is being triggered. TIMER TO PM ON TO ON TIMER ALERT This icon will flash when a countdown has completed in TIMER TO ON, TIMER TO OFF, CYCLE, or SCHEDULE Mode. DISPLAY LOCK ALERT This icon will display when you lock the controller. The icon will flash and beep if you attempt to adjust the controller while it is still locked.
OTHER SETTINGS FACTORY RESET To reset the controller back to factory settings, hold the mode button, the up button, and the down button simultaneously for four or more seconds. Resetting the controller will clear user settings in all modes and controller settings. CONTROLLER LOCK To lock the controller to prevent accidental changes or tampering, hold the settings button for two or more seconds. While the display is locked, you will not be able to switch modes or change any settings.
AC INFINITY PRODUCTS Inline Fans The CLOUDLINE series is a line of duct fans designed to quietly ventilate AV rooms and closets, as well as various DIY air circulation and exhaust projects. Features a thermal controller with intelligent programming that will automatically adjust duct fan speeds in response to changing temperatures. Carbon Filter The duct carbon filter is designed to eliminate odors and chemicals for grow tents and hydroponic spaces.
WARRANTY This warranty program is our commitment to you, the product sold by AC Infinity will be free from defects in manufacturing for a period of two years from the date of purchase. If a product is found to have a defect in material or workmanship, we will take the appropriate actions defined in this warranty to resolve any issues. The warranty program applies to any order, purchase, receipt, or use of any products sold by AC Infinity or our authorized dealerships.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
www.acinfinity.
