TVAC15000C US FR PT ES User guide Manual de instruções Manual de instrucciones You can find important information and FAQs about this and other products on the website www.abus.
English This user manual contains important information for the installation and operation of the TVAC15000C Home Surveillance System. Please take special care to store this manual for future reference. A list of contents with the corresponding page number can be found in the index on page 9. Français commande du système de surveillance du domicile TVAC15000C. Veuillez conserver ce manuel pour une utilisation ultérieure.
TVAC15000C 3.5" Home Video Surveillance System User manual Version 04/2014 Original user guide in English. Retain for future reference.
English Introduction Dear Customer, Thank you for purchasing the ABUS TVAC1500C Home Surveillance System. To ensure optimum performance and condition of this system is maintained, please read carefully the enclosed operating manual. This operating manual is meant to guide you through the process of operating the TVAC15000C Home Surveillance System. This ma relevant safety information.
English Icon explanation A flash in the triangle is used if there is danger for the health, e.g. by an electric shock. This triangular with the exclamation mark warning symbol indicates important notes in the operating instructions which should be observed. This symbol indicates special information bulletins and notes on the operation of the unit. Important safety advice All warranty claims are invalid in the event of damage caused by operating the system in non-compliance with this user guide.
English 7. Wireless transmission The range of wireless transmission depends on various environmental factors. The local conditions at the installation location can have a negative impact on the range. For this reason, if there is a clear line of sight between the receiver and the transmitter, the range can be as much as 490 feet, but in buildings it is significantly less.
English Unpacking While you are unpacking the device please handle it with utmost care. If you notice any damage of the original packaging, please check at first the device. If the device shows damages, please contact your local dealer. FCC Compliance Information Part 15 Compliance Statement This device complies with Part 15 of the FCC Rules.
English WARRANTY DURATION: This warranty to the original user shall terminate & be of no further effect 12 months after the date of original retail sale.
English Table of contents 1. Intended Use ......................................................................................................................................... 10 2. Scope of System Contents .................................................................................................................. 10 3. Features and functions ........................................................................................................................ 10 4. Information and FAQs ..
English 1. Intended Use You can use this 2.4 GHz wireless monitor and the IR wireless outdoor camera with PIR for easy wireless transmission and displaying of video signals across middle to long distances. Wireless signal transmission is an advantage in all locations where cables cannot be laid: the camera transmits the video signal to the wireless monitor without the need for wires. Faults and interference can be avoided due to the conversion into digital signals.
English 5. Device description 5.
English 5.2 Rear of the monitor Antenna Stand 5.3 Monitor connections SD card slot 5 V DC/1 A (DC, 14.5 × 4.
English 5.4 Camera description Antenna Light sensor Fixed lens Power LED LINK LED IR LED PIR sensor Camera mount Pairing button Power supply connection 5 V DC/1 A 5.5 Cable connections Yellow RCA plug (video) Connection for transmitting the video signal White RCA plug (audio) Connection for transmitting the audio signal Jack plug Plug for connecting to the monitor To connect the video RCA plug to a BNC input on a monitor or recorder, attach the BNC-RCA adapter to the yellow RCA plug.
English 6. Installation 6.1 Pairing the camera and monitor To connect a camera with the monitor, proceed as follows: 1. 2. 3. 4. Connect the power supply to the cameras and monitor. 4) and confirm your choice with OK. The systems starts a 60 second countdown. During the 60 seconds, press the PAIRING button on the camera cable until the green LINK LED on the front of the camera starts to flash. Upon successful connection of the camera the LINK LED is lit permanently.
English Then screw the camera onto the mount and the power supply unit with the camera. Warning: Only use the antenna provided for the installation. 6.3 Installing the monitor The installed battery gives you the option of using the TFT monitor flexibly. When the battery LED lights up red, the battery needs charging Make sure that the battery is always sufficiently charged in order to guarantee no loss of recording.
English To display the monitor display on another device, proceed as follows: 1. 2. Connect the jack plug to the monitor s AV OUT. Connect the RCA plug to the monitor as shown in the drawing. 7. Operation To switch the monitor ON/OFF, press and hold the power button for at least 2 seconds. Each time it is started, the monitor switches to live view and it selects the last view that was set. If the icon is displayed, the monitor has correctly identified the SD card and it is working normally. 7.
English Motion detection alarm activated No SD card inserted Full SD SD card full Err SD SD card was not identified SD card locked SD card is overwritten when it reaches capacity SD card display SD card capacity Power supply display Camera brightness display 01:12:45 Recording time 2011 05 01 14:30:11 Date/time display Please note: The icons disappear automatically after being displayed for ten seconds. 7.2 Main menu Press MENU to open the main menu.
English Event list: The recordings are stored in sub-folders named after the recording date. The recordings are stored as individual files with the time of recording as the file name.
English Pairing = add camera Use the select the desired camera and confirm your choice with OK. The systems starts a 60 second countdown. During the 60 seconds, press the PAIRING button on the camera cable until the green LINK LED on the front of the camera starts to flash. Once the connection is successful, the LINK LED on the camera lights up continuously and the monitor switches to live view. Resolution = image resolution resolutions 640 × 480 and 320 × 240. Confirm your input with OK.
English SD Card Overwrite = SD card circular buffer Use the deactivate (OFF) the SD card circular buffer. Confirm your selection with OK. The circular buffer is activated by default. Warning: When the memory capacity is reached, the monitor continues to record, deleting the oldest recordings on the SD card. The SD card capacity display flashes with 0.0 G in red. 7.5 Event list Event List = event list Use the arrow buttons to navigate between folders. Press the OK button to select the desired folder.
English 7.6 System settings Quad Display = four-way display Use the e quad display on (ON) or off. To activate quad mode, all the cameras have to be activated. When in quad display, you can use the arrow buttons to switch directly to full-screen view for individual cameras. = camera2; = camera3; = camera4 Note that the cameras that are hidden are not shown in the quad display. Warning: Only the full screen of the triggering channel is recorded.
English SD Card Format = format SD card You can use this to format the SD card. The system displays the memory that is currently available (Free) and the total memory (Total). Press OK to start formatting. Confirm your selection with and cancel the operation with . Warning: Format the SD card before using it for the first time. Power Saving = energy-saving mode saving mode ON or OFF. This function is activated by default. This function switches the screen to standby mode after two minutes.
English System Version = software version of the monitor and camera This function shows you the software versions of the monitor and all the connected cameras. 8. Maintenance and cleaning 8.1 Maintenance Regularly check the product's physical state, e.g. check for damage of the housing. If you suspect that safe operation cannot be guaranteed anymore, disconnect the product and ensure that it cannot be used by mistake.
English 9. Disposal and Lithium-Polymer Battery Warning 9.1 Lithium-Polymer Battery Warning This equipment contains a rechargeable lithium-polymer battery. Do not charge the battery in temperatures below 32° F or higher than 112° F. Do not open or mutilate the battery. The rechargeable batteries contained in this equipment may explode if disposed of in a fire. Do not short-circuit the battery.
English 10. Tips for troubleshooting No. Question Answer 1 Pairing creates the exclusive, encrypted wireless connection between the monitor and camera. What does pairing the monitor and camera mean and how does this work? To connect a camera to the monitor, proceed as follows: 1. Connect the power supply units to the cameras and the monitor. 2. select a camera (1-4) and confirm the selection with OK. The system counts down from 60 seconds. 3.
English 11.Technical data Model number Frequency Modulation Sensitivity TV lines Image sensor Resolution No. of IR LEDs Lens Angle of view PIR angle of view PIR range Night vision function range IR swivel filter IP protection class Wireless range Power supply Power consumption Operating temperature Dimensions (L × W × H) Weight TVAC15000C Camera 2402-2480MHz GFSK -82 dBm 400 TVL 1/4" CMOS 640 × 480 pixel (VGA) 27 IR LEDs 3.6 mm 56° (H)/43° (V) 60° (H)/50° (V) Max. 16 feet approx. 32 feet Yes IP66 approx.