SIDE: 9' 10 7⁄64" HEIGHT: 6' 10 43⁄64" ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H AU: 1800 029 701 N Z: 0800 466 444 admin@absco.com.au www.abscosheds.com.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H GENERAL INSTRUCTIONS • Before commencing any assembly, read through these instructions in detail to gain a thorough understanding of assembly methods and associated details. • Unpack the carton and carefully identify and check off all the parts against the parts described and illustrated on "COMPONENTS PACKING LIST" pages. • Local authority approval must be obtained prior to construction of the shed.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H COMPONENT PACKING LIST Check off all components. SHEET PACK- 3030RSSP QTY COMPONENT DESCRIPTION 8 STEEL SHEET 5’ 2 3/16” LONG 2’ 6 7/16” WIDE 2 STEEL SHEET 7’ 10 1/2” LONG 2’ 6 7/16” WIDE 2 STEEL SHEET 7’ 5 3/8” LONG 2’ 6 7/16” WIDE PART No. 158S 2400L 2270L CHK QTY COMPONENT DESCRIPTION PART No.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H COMPONENT PACKING LIST Check off all components. FRAME PACK - 3030RSFP COMPONENT DESCRIPTION QTY 14 FRAME SECTION L = 9’ 8 “ C 2 J 4 K 4 M PART No. FRAME SECTION L = 7’ 7 1/8” FRAME SECTION L = 4’ 7 11/16” FRAME SECTION L = 4’ 10 11/16” C2946 2 C J2315 6 C K1415 4 C FRAME SECTION L = 7’ 6 3/8” FRAME SECTION L = 6’ 9 1/8” FRAME SECTION L = 3 15/16” PART No.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Frame Section Identification Guide There are several types of frame section, each featuring a different combination of notches and/or holes. Frame sections are coded with a letter representing the type of frame section, followed by the length of the frame section in millimeters.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Guide for Connecting Frame Sections Absco sheds’ frame assemblies are supplied with 10-16x16 self drilling wafer head phillips drive tek screws The wafer head minimises distortion to the sheet cladding once it is fitted to the frame Ensure that driver bits used to fasten these screws is phillips drive, as similar alternatives (EG. Pozi drive) increases the risk of stripping the head of these screws.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Overview Of Internal Frame Absco Industries Assembly Instruction Manual Model: 3030RS-PTX 19/07/2019 1.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Side Wall Frame Assembly BKT11 2 required. J2315 C2295 Boxed M1490 C2060 ZACO200 K1465 C2060 BOXED SECTIONS BKT17 C2295 C0100 C2060 J2315 Absco Industries ” 1’ 6 1/2 1’ 6 1/2 ” 1’ 6 1/2” 2”* Align centre BKT11 with edge of ZACO200 as shown. 11 ’1 3 15/16” 3’ 7 11/16” 7’ 7 5/16” to apex ” 1’ 6 1/2 Assembly Instruction Manual 05 *NOTE: One side will have a fourth bracket to mount the rear purlin.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Rear Frame Assembly 1 required. 2x C2060 Boxed K1415 BOXED SECTION BKT17 C2020 Absco Industries 3 15/16” 3’ 7 11/16” C2020 Assembly Instruction Manual Model: 3030RS-PTX 19/07/2019 1.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Prepare Edge Beam Assemble the Outer beam and Inner beams on the ground first using wafer head tek screws (FAST014) at 5 7/8” spacings. Remove the left and right outer beams (ZACO213) before installing to the wall frames. This will makes fastening the easier as the holes will already be there and will align.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Wall Frame Assembly NOTE: During frame construction the structure will be unstable until complete. Consider using bracing, timber or rope to stabilise and prevent twisting or collapse. 3 1/8” Stand both side walls and join with rear frame then the edge beam. NOTE: Orientate side frames so rear purlin bracket is to the rear of shed. E R EA M RA F SIDE R Fasten the partially assembled edge beam to side frames as shown.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Purlin Assembly Fasten purlins to the purlin brackets. Six purlins are placed on the high side of each purlin bracket. The rear purlin must be positioned on the outside of the reversed bracket. Fasten the purlin to each bracket using 4 tek screws. Absco Industries Assembly Instruction Manual INTERNAL VIEW OF REAR STUD Using two multipurpose brackets (BKT17) secure the rear wall stud to the rear purlin.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Anchoring NOTE: • For installation next to buildings, fences or other obstacles, the side walls or rear wall may best be cladded before anchoring. • Guttering also may be best fitted prior to anchoring. Recommended slab dimensions - 2950mm Wide x 2975mm Deep For footing sizes in lieu of a slab refer to engineering drawings.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Roof Sheet Cladding Mark a centre line along the purlins, place the first sheet (158S) on the roof frame and align the centre of the edge rib of the sheet. Once aligned, fit Tek screws (FAST035) fitted with neoprene washers (FAST043) through the middle of the adjacent pan and into the frame section beneath it. Check and adjust the alignment of the opposite side of the sheet, and then fit the remaining fasteners.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Wall Sheet Cladding 214 Rear wall is 4x 214 sheet 2270R 2400R TR19 2400L Repeat the process described for the roof sheeting cladding for the side wall and back wall. Be sure to fasten where the sheets overlap. 2270L Use screws every second pan, fastening sheets top and bottom girts and the edge roof purlin. Fasten sheets to all frame uprights at 11 13/16” spacings.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Gutter Installation FAST009 Place the TR25 gutter end caps on each end of the TR22 gutter. Drill 1x 1/8” hole through the front, back and underside of where the TR25 overlaps the TR22, and fit 1x FAST009, Pop Rivet into each hole. Silicone can be used to create a water tight seal at these connections.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Gutter Installation Mount the TR22 gutter onto the RWG06 gutter brackets ensuring that all loops on the RWG06 gutter brackets interlock into the loop of the gutter profile.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Trim Installation TR06 TR08 TR06 Fit barge capping to gable end walls, fixing through the roof at purlin locations. Lay the ridge capping centrally on the roof, overlapping the sections to attain the required length equivalent to the roof sheeting, and fix to every second rib of the roof sheeting with screws and neo washers. NOTE: Avoid walking on the roof so sheeting is not damaged.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Clean Up & Troubleshooting • Photograph the completed assembly for future reference • Reduce the risk of corrosion by hosing or blowing the completed structure to remove metal shavings, particularly those from on top of painted surfaces • Where components and/or assemblies appear to not be aligning, refer to check measurements provided with each process, as well as the measurements provided within the components parts checklis
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H Absco Sheds Storage Guidelines • Absco Sheds are designed to be weatherproof for normal weather conditions. In the event of extreme weather conditions such as heavy rain, combined with high wind gusts, the ridge capping, sheeting joins, screw fixings etc., may exhibit minor deformations which may allow some water entry. These areas should be checked regularly to ensure that maximum strength and protection is maintained.
ABSCO RURAL SHED MODEL: 3030RS-PTX 9’ 9 5/16” W x 9’ 9 5/16” D x 8’ 7/16” H EXPORT PRODUCT WARRANTY AGAINST DEFECTS Congratulations on your purchase of an ABSCO SHED ABSCO SHEDS, including garden sheds, garden beds, aviaries, storage units, garages, awnings and carports are made using high quality Australian made steel. We are pleased to advise we warrant that the steel coating will not rust, crack, flake peel or blister for 12 years from date of purchase.