Instruction for Danale DVR V1.3 DVR connection diagram Interface definition specifications DC 12V RS485 DC12V power input interface PTZ control signal interface RJ45 Ethernet port USB interface AUDIO IN Audio input interface VGA VGA interface for connecting a VGA monitor H-DMI HDMI interface for connecting a HD monitor AOUT Audio output interface VIDEO IN Camera signal input interface Login upon booting * The login interface is popped up after booting.
Hard drive installation * The equipment supports 500GB to 6TB hard drive; Size requirements are presented as follows: SATA, 3.5 ''; USB hard drive can only be used for backup, rather than video storage.
Note: After the hard disk is installed, you need to format the hard disk, as shown in the figure below:
Record *Please make sure that the successfully-formatted hard disk is installed in the equipment before recording. Steps for recording are presented as follows: There are three record modes: Motion Detect: Recording is started when a motion alarm is detected. Schedule: Recording period can be set, which can be recorded in three modes, namely, Regular, Detect and Alarm. Manual: Recording is started manually without a division of alarm and motion detect. Note: The system default is recorded 24 hours a day.
④Playback * After half-an-hour recording, a recording file will be generated, which can be searched according to the time and played back.
⑤ Channel type * DVR is a five-in-one hard disk recorders; CVBS / AHD / TVI / CVI will be automatically identified, when getting access. When accessing a network device, a corresponding channel type should be selected according to the accessed IPC equipment. Note: Channel type switching is not supported for POE recorder.
⑥ Motion detect *The equipment supports motion detect and motion detect recording; Steps for setting are presented as follows: 1. Enter the main alarm menu; 2. Select a channel and enable it, then click Advanced 3. Select corresponding setting options as required after entering the interface of motion detect.
Described definitions of each option are presented as follows: Sensitivity The higher the sensitivity of the motion detect is, the easier the motion detect alarm will be triggered. Region Deployment region is to conduct the motion detect deployment (the whole area default) in the area of the channel interface; Period Deployment time is to set the period for opening motion detect; Interval/Sec.
⑦ Email settings * The equipment supports to push alarm messages to your E-mail; Before that, you shall set your email address in advance. Steps for that are presented as follows: 1.Click the right mouse button to select Network Settings for entering the interface of network settings, and then, select Email to set up your mailbox; 2.Check and Enable it to set corresponding parameters.
is connected to the Internet. Steps for setting are presented as follows: 1.Connect the equipment to a router that is connected to the Internet through the Ethernet Cable; 2.Click the right button to select Network settings on the DVR menu for entering the interface of network setting and setting Network. After that, check DHCP Enable to make DHCP not enable and click Application; 3.
4.When Nat status of the equipment is displayed Connected, you can search and install Danale app in the Google Play or APP Store on your phone; And then, you can use the email or phone number for registration and login, as shown below: 5.
will be automatically displayed on the main menus of the APP. You can click it for previewing.
⑨ Computer client remote control * The equipment supports computer client remote monitoring; You shall add the equipment in the phone APP before the use of computer client. Steps for operating the computer client remote monitoring are presented as follows: 1.Type the d.jooan.cc into your browser's address bar for entering into the download network disk; You can select a corresponding CMS software for downloading according to systems of different PC ends. after successful installation; Use the 2.
⑩ LAN access *The equipment supports access of LAN IP address; Steps for that are presented as follows: 1.Connect the DVR and the computer to the same LAN. 2.Open the browser and press Enter after typing the IP address of the DVR in the browser; 3.If a plug-in is prompted to download, please log in again after installing the plug-in. It will be directly accessed to the login interface, if there is no prompt. 4.
Attached (FAQ): Question 1: If the DVR cannot be started after booting, what shall I do? Answer: Possible reasons: 1.Incorrect input power; 2. It fails to be energized normally; 3. The power adapter is damaged; 4. Damaged hard disk damage or damaged hard disk line.
acceptable resolution of the DVR; 2. The software program does not match, please contact customer service to send the latest firmware upgrade; 3. The image brightness is changed to 0; It can be restored the equipment to the default setting; 4. No input signal or weak input signal, please check the connection between the camera and the DVR. Question 6: What shall I do if a recording cannot be found in the local playback? Answer: Possible reasons: 1. The DVR is failed to identify the hard disk 2.
Internet mode? Answer: When Onvif IP Camera is connected under the network mode, the motion detect is not supported. Attached (after-sales): E-mail: technicalreply@qacctv.com Skype: market@qacctv.
