EUT : 1M Phone line Network, 10/100 Fast Ethernet PC Card FCC ID : MQ4HF1KA Kaboom Systems, Inc.
FEDERAL COMMUNICATIONS COMMISSION NOTE iis equipment has been tested and found to comply with the limits for a Class B .Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
[CoS INTRODUCTION HARDWARE INSTALLATION. SOFTWARE INSTALLATION Nov ell Wetware . MS LAN Manager. Windows 95 Installation Artistic Fantastic 6.0 Installation {BM OS/2 Warp GENERAL INFORMATION. NOTES FOR DIS DRIVER .. NOTES FOR PACKET DRIVER. NOTES FOR WINDOWS FOR WORK GROUPS DRIVER QUESTIONS AND ANSWERS.
INTRODUCTION ‘ ABOUT THIS MANUAL This manual will explain how to install and use your 10/100Mbps dual speeds Fast Ethernet PC Card. The following guideline will help you through the installation process. How to install the Card and Connect it to network => Chapter 1. Hardware Installation How to install the network driver => Chapter 2. Software Installation How to do trouble shooting <> Chapter 4.
Introduction on * Microsoft LAN Manager ® Packet Driver Applications *» Microsoft Windows for Work groups 3.11 * Microsoft Windows 3.1 * Microsoft Windows NT 3.51, NT 4.0 * Windows 95 * Fantastic 6.0 « IBM OS/2 Warp Version 3 CONTENTS IN THE PACKAGE Past Theme PC Card Adapter * Media couplet with single JR-45 connector for ABASE-T and 100BASE-TX network. * 3.
Hardware installation HARDWARE INSTALLATION This chapter describes how to install the dual speeds Fast Ethernet PC Card in your notebook computer and connect it to network. It’s referred to “the PC Card™ in this manual. The PC Card could be connected to either 100Mbps Fast Ethernet or 10Mbps Ethernet over shielded twisted pair (UTP) cable. The PC Card have the ability automatic sensing and operating on either speed without manual reconfiguration. Please refer to Chapter.
Hardware Installation teeter Removing the Dual Speed Fast Ethernet PC Card I's quite different for various computer mechanical design. Please refer to the PC Card removal instruction in the document for your notebook computer. — Connecting and Removing the Cable of Media Couplet to the PC Card Grasp the PC Card 15-pins connector at the end of the media couplet with the pointing triangle facing upward. Gently insert it into the mating connector on the PC Card until it clicks in place at both sides.
Hardware instillation Connecting to the Network Connect shielded twisted pair (UTP) cable to the JR-45 connector of media couplet before loading any network driver. @ For operation in the100Mbps (base's-TX) Ethernet network, a Category 5 shielded twisted pair{ UTP) cable should be used to connect between media couplet and 100Mbps hub or switch.
Software installation SOFTWARE INSTALLATION Plug the driver diskette into the floppy drive and set the current drive to the floppy drive. Then run INSTALL to install the real mode drivers such as ODI or DIS 2.x or Packet Drivers into the target disk. Nov ell Wetware There are two methods to install the Wetware client ODI driver, the menu installation and Wetware 3.12 or 4.x Client installation. Menu Installation 1.Run INSTALLMENT from the root directory of driver diskette.
Software installation 2.Select Wetware 3.x and 4.x Workstation” item from menu. 3.If current settings are acceptable, select Start Installation and go to step 5. Otherwise, select Modify Parameters to make settings changed 4.Move cursor to focus on the setting you want to make change and press ” to select a fit value. When the configurations are set completely, press on the OK” field to exit the screen and go back to step 3. 3.
Software installation If you wanted to install the ODI driver by manual, you may follow the instructions list below. 1.Copy the files LE100ODI.COM and NETTING from the path \WETWARE and the file ENPLANE from the path \ENABLER in the driver diskette into the Wetware client directory containing Nov ell's LIPSCOMB, IPXODI.COM and Nettlesome files. 2.Using a text editor to edit the NETTING for setting the default frame type. In the Wetware server the frame type is set to 802.3 for NW3,11 and 802.2 for NW3.
Software Installation LE100ODI.COM whenever a reference is made to the Hardware Specific Module. 4.A typical ODI workstation startup batch file includes: ENPLANE /IRQ=dd fIOP=xx Card Enabler >LsL :Link Support Layer Module provided by Nov ell >LE1000DI :Hardware Specific Module >IPXO0! JINX Protocol Stack Module provided by Nov ell Sonnet 1 Shelf Support Module provided by Nov ell LOGIN Novel! Client Installation 1.Run the Net Ware Client Install V1.