Manual Number : SP-ZZ1GV-06 W-LAN+Bluetooth Combo Module LBEE5ZZ1GV-893 Manual Broadcom Chipset for 802.11b/g/n + Bluetooth 4.
Manual Number : SP-ZZ1GV-06 1 / 20 The revision history of the product specification Issued Date Revision Page Oct.23, 2015 Revision Code - Oct.28, 2015 02 P32 - Changed Items First Issue Add chapters of WLAN operation and Bluetooth Operation Nov.2, 2015 03 Change order of the chapters. And remove “Taping and Reel Pacing”, “NOTICE”, and “PRECONDITION TO USE OUR PRODUCTS” Nov.10, 2015 04 Remove “Block Diagram” P7,8,9 Nov.20, 2015 05 Cover Page P4 P18-P24 P18(new) Dec.
Manual Number : SP-ZZ1GV-06 2 / 20 TABLE OF CONTENTS 1. WLAN Function Start Guide ............................................................................................................... 3 1.1. Hardware Setup ............................................................................................................................. 3 1.2. Software Setup ............................................................................................................................... 3 2.
Manual Number : SP-ZZ1GV-06 3 / 20 1. WLAN Function Start Guide 1.1. Hardware Setup 1. Connect Power input pins (VBAT, VDDIO) to power supply circuit. 2. Connect SDIO interface pins (WL_SDIO_CLK, WL_SDIO_CMD, WL_SDIO_D0 to WL_SDIO_D3) to an SDIO interface of host processor like Micro Controller Unit or PC. (See 5. Dimensions, Marking and Terminal Configurations.) 3. Connect Other IO lines (for ex. WL_REG_ON) to the host processor IO terminal. 4. Connect 32kHz LPO to the input pin of the module. 5.
Manual Number : SP-ZZ1GV-06 4 / 20 5. Dimensions, Marking and Terminal Configurations < TOP View> < Side View > < TOP View> (1) Model： 1GV 893 (4) (3) XXXXXXXXX M (2) Dimensions Mark L a1 b2 e1 e4 e7 m1 Marking Marking (1) (2) (3) (4) Dimensions 9.5 +/- 0.2 0.35 +/- 0.1 0.20 +/- 0.15 0.35 +/- 0.1 0.375 +/- 0.1 1.225 +/- 0.1 1.0 +/- 0.1 Mark W a2 c1 e2 e5 e8 m2 Dimensions 15 +/- 0.2 0.35 +/- 0.1 0.65 +/- 0.1 0.35 +/- 0.1 1.225 +/- 0.1 1.625 +/- 0.1 1.0 +/- 0.
Manual Number : SP-ZZ1GV-06 5 / 20 Terminal Configurations 1 50 49 48 47 46 45 44 43 42 41 40 2 39 3 38 4 51 58 57 37 5 36 6 35 7 34 8 52 59 56 33 9 32 10 31 11 30 12 53 54 55 29 13 28 14 27 15 16 17 18 19 20 21 22 23 24 25 Preliminary & Confidential < Specification may be changed without notice > 26
Manual Number : SP-ZZ1GV-06 6 / 20 Pin# 1 2 3 4 5 Pin Name GND GND WLAN_BT_ANT GND GND Type ─ ─ I/O ─ ─ 6 WL_GPIO_2 I/O 7 8 9 10 11 12 13 14 15 GND WL_SDIO_CLK GND WL_SDIO_D2 WL_SDIO_CMD WL_SDIO_D0 WL_SDIO_D3 WL_SDIO_D1 GND ─ I ─ I/O I/O I/O I/O I/O ─ 16 WL_HOST_WAKE(WL_GPIO_0) I/O 17 WL_GPIO_1 I/O 18 WL_REG_ON 19 20 21 22 23 VDDIO GND VBAT VBAT GND 24 BT_REG_ON 25 26 27 LPO_IN GND GND I ─ ─ 28 BT_PCM_CLK I/O 29 BT_PCM_SYNC I/O 30 31 BT_PCM_OUT BT_PCM_IN O I 32 BT_UART_RTS_
Manual Number : SP-ZZ1GV-06 7 / 20 SDIO Pin Description No.
Manual Number : SP-ZZ1GV-06 8 / 20 6. Rating min. -40 -0.5 -0.5 Storage Temperature Supply Voltage VBAT VDDIO max. +85 5.0 3.9 unit deg.C V V * Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. No damage assuming only one parameter is set at limit at a time with all other parameters are set within operating condition. 7.
Manual Number : SP-ZZ1GV-06 9 / 20 Power On Sequence for WLAN ON and BT Off 32.768kHz Sleep Clock VBAT 90% of VH VDDIO >2 Sleep cycle WL_REG_ON BT_REG_ON Power On Sequence for WLAN OFF and BT ON 32.768kHz Sleep Clock VBAT 90% of VH VDDIO >2 Sleep cycle WL_REG_ON BT_REG_ON Power On Sequence for WLAN OFF and BT OFF 32.
Manual Number : SP-ZZ1GV-06 10 / 20 WLAN Boot up Sequence Ramp time from 0V to 4.3V > 40µs VBAT 0.6V > 2 sleep clock cycles VDDIO < 1.5 ms WL_REG_ON < 3 ms VDDC (from internal PMU) < 50 ms After a fixed delay following internal POR going high, the device responds to host F0 (address 0x14) reads Internal POR Device requests a reference clock 15 ※ 1 ms After 15※ 1ms the reference clock is assumed to be up. Access to PLL resistaers is possible.
Manual Number : SP-ZZ1GV-06 11 / 20 Startup Signaling Sequence Host IOs unconfigured Host IOs configured VDDIO Host ResetX T1 BT_GPIO_0 (BT_DEV_WAKE) T2 BT_REG_ON BTH IOs configured BTH IOs unconfigured T3 BT_GPIO_1 (BT_HOST_WAKE) Host side drives this line low BT_UART_CTS_N BT_UART_RTS_N T4 BTH device drives this line low indicatong transport is ready Driven Pulled T1 is the time for host to settle it’s IOs after a reset.
Manual Number : SP-ZZ1GV-06 12 / 20 8. Digital I/O Requirements SDIO Interface I/O Pins Input low voltage (VDDIO = 3.3V) Input high voltage (VDDIO = 3.3V) Input low voltage (VDDIO = 1.8V)) Input high voltage (VDDIO = 1.8V) Output low voltage (VDDIO = 3.3V) Output high voltage (VDDIO = 3.3V) Output low voltage (VDDIO = 1.8V) Output high voltage (VDDIO = 1.8V) Sym VIL VIH VIL VIH VOL VOH VOL VOH min. 0.625*VDDIO 1.27 0.75*VDDIO 1.40 max. 0.25*VDDIO 0.58 0.125*VDDIO 0.
Manual Number : SP-ZZ1GV-06 13 / 20 10. Interface Timing 10.1. SDIO Timing (Default Mode) fPP tWL tWH CLK tTHL tISU tTLH tIH Input Output tODLY (max) tODLY (min) Parameter Symbol Min(1) Clock CLK (All values are referred to min. VIH and max.
Manual Number : SP-ZZ1GV-06 14 / 20 10.2. SDIO Timing (High Speed Mode) fPP tWL 50% VDD tWH CLK tTHL tISU tTLH tIH Input Output tODLY tOH Parameter Symbol Min(1) Clock CLK (All values are referred to min. VIH and max.
Manual Number : SP-ZZ1GV-06 15 / 20 10.4.
Manual Number : SP-ZZ1GV-06 16 / 20 10.5.
Manual Number : SP-ZZ1GV-06 17 / 20 10.7.
Manual Number : SP-ZZ1GV-06 18 / 20 11. Notice Please describe the following warning on the final product which contains this module. 11.1. FCC Class B: (Section 15.105) FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Manual Number : SP-ZZ1GV-06 19 / 20 End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 5 mm may be maintained between the antenna and users.
Manual Number : SP-ZZ1GV-06 20 / 20 End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 5 mm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: "Contains IC: 4634A -6152EC “.
