AELOLW\ WSDB-706GN Hardware & Software Setup Guide Rev. 0.2a Doc.
1. WLAN Function Quick Start Guide Physical hardware configuration likes as figure1. Please follow the following procedure step by step to get starting WLAN function. SDIO Board Software setup: Follow driver installation procedure steps to install the GB9662 driver on your PC (OS: XP). 1-1.Copy WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\Nvram\GB9662_NVRAM_V1.1_09132 012.TXT to C:\Windows\system32\Drivers 1-2. Copy Test Board Socket WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\5_90_153_49_43362_mfg_A2(Dr
1-5.Choose install from a list or specific location (Advanced), and then click Next. 1-6.Choose Don’t search, I will choose driver to install, and then click Next. 2 Doc.
1-7.Click Have Disk . 1-8.Click Browse to choose correct directory of Driver 3 Doc.
WDSB-706GN\WSDB-706GN_Driver_V1.2_10122012\5_90_153_49_43362_m fg_A2(Driver) \bcmsddhd.inf and then click OK to next step. 1-9.Choose Broadcom 802.11g Network Adapter and click Next to install driver. 1-10.Click Finish and you can check the device is working fine in Device Manager. 4 Doc.
1-11.In Device Manager, Choose Broadcom 802.11g Network Adapter right button of mouse and then choose content. and click 1-12.In the tab of Advanced, choose 5 Doc.
1-13.In the tab of Advanced, choose 43362ROMImagePatch item and replace with \SystemRoot\system32\drivers\ GB9662_NVRAM_V1.1_09132012.TXT and then click OK button. 6 Doc.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
manual.The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. For body-worn operating conditions please use belt-clips, holsters, and/or accessories that have no metallic component in the assembly and must provide at least 0.2cm separation between the device and the user's body.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) Theproduct modulecan antenna must be as installed to from keepthe at least 0.2cmorfrom thedevice user body. 1)The be kept as far possible user body set the to 2)lower The transmitter module may not be co-located with any other transmitter or output power if such function is available. antenna. 2)The transmitter module may not be co-located with any other transmitter or antenna.
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
Manuel d'information à l'utilisateur final L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel. 12 Doc.