Cut Sheet

ManualsBrandsABB ManualsPower DistributionCp-e Power Supply 24vdc 5 Amp

Data sheet

Power supply CP-E 24/5.0

Primary switch mode power supply

The CP-E range offers enhanced functionality

while the number of different types has been

considerably reduced. Now all power supply units

can be operated at an ambient temperature of up

to +70 °C.

Characteristics

– Rated output voltage 24 V DC

– Output voltage adjustable via front-face rotary

potentiometer “OUTPUT Adjust”

– Rated output current 5 A

– Rated output power 120 W

– Supply range 115/230 V AC (90-132 V AC,

180-264 V AC, 210-375 V DC), auto select

– Typical efﬁciency of 86 %

– Low power dissipation and low heating

– Free convection cooling (no forced cooling with ventilators)

– Ambient temperature range during operation -35...+70 °C

– Open-circuit, overload and short-circuit stable

– Integrated input fuse

– Redundancy unit CP-A RU offering true redundancy,

available as accessory

– Signalling contact “13-14” (solid-state) for output voltage OK

– LEDs for status indication

Approvals

UL 508, CAN/CSA C22.2 No.107.1

ANSI/ISA-12.12, CAN/CSA C22.2 No. 213

(Class I, Div. 2, hazardous locations)

UL 60950, CAN/CSA C22.2 No.60950

EAC

CCC

Approval refers to rated input voltage U

Marks

RCM

2CDC 271 024 F0008

Order data

Type Input voltage range Rated output voltage / current Order code

CP-E 24/5.0 90-132 V AC / 180-264 V AC

210-375 V DC

24 V DC / 5 A 1SVR 427 034 R0000

Order data – accessories

Type Description Order code

CP-A RU Redundancy unit

The CP-A RU provides decoupling of two CP-E power supply units ≤ 40 V and ≥ 5 A.

1SVR 427 071 R0000

Summary of content (11 pages)

PAGE 1
Data sheet Power supply CP-E 24/5.0 Primary switch mode power supply 2CDC 271 024 F0008 The CP-E range offers enhanced functionality while the number of different types has been considerably reduced. Now all power supply units can be operated at an ambient temperature of up to +70 °C.
PAGE 2
Functions XXXXXXXXXXXXXXX 1 OUTPUT L+, L+, L-, L-: terminals – output 3 1 7 6 4 5 8 2 INPUT L, N, PE: terminals – input 3 13-14: terminals – signalling contact 4 OUTPUT LOW: red LED – output voltage too low 5 OUTPUT OK: green LED – output voltage OK 6 OUTPUT Adjust: 2 potentiometer – adjustment of the output voltage 7 single/parallel: sliding switch – adjustment of single or parallel operation 8 Circuit diagram Application The primary switch mode power supply offers two voltage input ranges.
PAGE 3
Installation Mounting 2CDC272017F0b08 2CDC 272 017 F0b08 The switch mode power supply can be snapped on a DIN rail according to IEC/EN 60715 as shown in the accompanying picture. For that the device is set with its mounting rail slide on the upper edge of the mounting rail and locked by lifting it downwards. Demounting 2CDC272018F0b08 2CDC 272 018 F0b08 Remove the switch mode power supply as shown in the accompanying picture.
PAGE 4
Electrical connection Connect the input terminals L and N. The protective earth conductor PE must be connected. The installation must be executed acc. to EN 60950, provide a suitable disconnecting device (e. g. line protection switch) in the supply line. The input side is protected by an internal input fuse. Rate the lines for the maximum output current (considering the short‑circuit current) or provide a s eparate fuse protection.
PAGE 5
Safety instructions and warnings The device must be installed by qualified persons only and in accordance with the specific national r egulations (e.g., VDE, etc.). The devices are maintenance-free chassis-mounted units. Disconnect system from supply network! Before any installation, maintenance or modification work: Disconnect the system from the supply n etwork and protect against switching on.
PAGE 6
Technical data Data at Ta = 25 °C, Uin = 230 V AC and rated values, unless otherwise indicated Input circuits Supply circuits Rated input voltage Uin L,N 115 / 230 V AC Input voltage range AC 90-132 V, 180-264 V DC 210-375 V AC 47-63 Hz auto select Frequency range Typical input current at 115 V AC 2.2 A at 230 V AC 0.83 A Typical power consumption 140 W Inrush current limiting Discharge current at 115 V AC 24 A (max. 5 ms) at 230 V AC 48 A (max.
PAGE 7
Output circuit – no-load, overload and short-circuit behaviour Characteristic curve of output U/I characteristic curve Short-circuit protection continuous short-circuit proof Short-circuit behaviour continuation with output power limiting Overload protection output power limiting No-load protection continuous no-load stability Starting of capacitive loads 3500 µF General data Power dissipation typ. 20 W Efficiency typ. 86 % Duty time 100 % Dimensions (W x H x D) 63.2 x 123.6 x 123.
PAGE 8
Electromagnetic compatibility Interference immunity to IEC/EN 61000-6-2 electrostatic discharge IEC/EN 61000-4-2 Level 4 (air discharge 15 kV / contact discharge 8 kV) radiated, radio-frequency, IEC/EN 61000-4-3 Level 3 (10 V/m) electrical fast transient / burst IEC/EN 61000-4-4 Level 4 (4 kV / 5 kHz) surge IEC/EN 61000-4-5 L-L Level 3 (2 kV) / L-PE Level 4 (4 kV) conducted disturbances, induced by IEC/EN 61000-4-6 Level 3 (10 V) power frequency magnetic fields IEC/EN 61000-4-8 Level 4 (3
PAGE 9
Technical diagrams Output behaviour Uout [V] 28 24 2CDC272006F0b08 20 16 12 4 1 2 3 4 6 5 8 7 Iout [A] 2CDC 272 006 F0b08 8 Characteristic curve of output at Ta = 25 °C The switch mode power supply CP‑E 24/5.0 is able to supply at 24 V DC output voltage and –– at an ambient temperature of: ≤ 60 °C a continuous output current of approx. 5 A –– at ambient temperatures of: 60 °C < Ta ≤ 70 °C the output power has to be reduced by 2.5 % per °C temperature increase.
PAGE 10
Dimensions accessories in mm [inches] 93,5 [3.68”] 203,5 [8.01”] 56,5 [2.22”] 90,0 [3.54”] 200,0 [7.87”]  2CDC 272 015 F0b07 130,0 [5.12”]  130,0 [5.12”] 130,0 [5.12”]  60,0 [2.36”] 2CDC272015F0b07 144,5 [5.69”] 137,0 [5.39”] 135,5 [5.
PAGE 11
Contact us Document number 2CDC 114 060 D0201 (08/2016) ABB STOTZ-KONTAKT GmbH P. O. Box 10 16 80 69006 Heidelberg, Germany Phone: +49 (0) 6221 7 01-0 Fax: +49 (0) 6221 7 01-13 25 E-mail: info.desto@de.abb.com You can find the address of your local sales organisation on the ABB home page http://www.abb.com/contacts -> Low Voltage Products and Systems Note: We reserve the right to make technical changes or modify the contents of this document without prior notice.