Rugged Expandable Touch Panel PC AGP-3175 AGP-3175 ® Intel Core™ i7/i5 Processor Rugged Touch Panel Computer With 17” TFT LCD & Two PCI/PCIe expansion slots AGP-3175 Manual 4th Ed June 2012
Rugged Expandable Touch Panel PC AGP-3175 Copyright Notice This document is copyrighted, 2012. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
Rugged Expandable Touch Panel PC AGP-3175 Acknowledgments AMI is a trademark of American Megatrends Inc. IBM, PC/AT, PS/2 and VGA are trademarks of International Business Machines Corporation. Intel® and Core™ i7/i5 are trademarks of Intel® Corporation. Microsoft Windows® is a registered trademark of Microsoft Corporation. RTL is a trademark of Realtek Semi-Conductor Co., Ltd. ESS is a trademark of ESS Technology, Inc. UMC is a trademark of United Microelectronics Corporation.
Rugged Expandable Touch Panel PC AGP-3175 Packing List Before you begin installing your card, please make sure that the following materials have been shipped: 1 AGP-3175 1 Jumper Cap 2 Easy stand & 4 screws 12 Panel Mount clips & screws 1 HDD plate & 4 anti-vibration rubbers & 4 screws 1 Power Cord (optional) 1 CD-ROM for manual (in PDF format) and drivers If any of these items are missing or damaged, you should contact your distributor or sales representative immediately
Rugged Expandable Touch Panel PC AGP-3175 Safety & Warranty 1. Read these safety instructions carefully. 2. Keep this user's manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Do not use liquid or spray detergents for cleaning. Use a damp cloth. 4. For pluggable equipment, the power outlet must be installed near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Rugged Expandable Touch Panel PC d. AGP-3175 The equipment does not work well, or you cannot get it to work according to the users manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20° C (-4°F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT. 16.
Rugged Expandable Touch Panel PC AGP-3175 Below Table for China RoHS Requirements 产品中有毒有害物质或元素名称及含量 AAEON Panel PC/ Workstation 有毒有害物质或元素 部件名称 铅 汞 镉 六价铬 多溴联苯 多溴二苯醚 (Pb) (Hg) (Cd) (Cr(VI)) (PBB) (PBDE) × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ × ○ ○ ○ ○ ○ 硬盘 × ○ ○ ○ ○ ○ 液晶模块 × ○ ○ ○ ○ ○ 光驱 × ○ ○ ○ ○ ○ 触控模块 × ○ ○ ○ ○ ○ 电源 × ○ ○ ○ ○ ○ 印刷电路板 及其电子组件 外部信号 连接器及线材 外壳 中央处理器 与内存 O：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T 11363-2006 标准规定的限量要求以下。 X：表示该有毒有害物质至少在该部
Rugged Expandable Touch Panel PC AGP-3175 Contents Chapter 1 General Information 1.1 Introduction................................................................ 1-2 1.2 Feature ...................................................................... 1-3 1.3 Specification .............................................................. 1-4 1.4 Dimension ................................................................. 1-7 Chapter 2 Hardware Installation 2.1 Safety Precautions ................................
Rugged Expandable Touch Panel PC AGP-3175 2.16 RS-232 Pin Header (COM3~4) ............................... 2-9 2.17 SATA Connector (SATA 1~3) ................................. 2-9 2.18 SATA Power Connector (PWR1) ............................ 2-9 2.19 Hard Disk Drive Installation..................................... 2-10 2.20 Easy Stand Installation............................................ 2-14 2.21 Panel Mount Kit Installation..................................... 2-17 2.22 Waterproof Protection ........
Rugged Expandable Touch Panel PC AGP-3175 Chapter 1 General Information Chapter 1 General Information 1-1
Rugged Expandable Touch Panel PC AGP-3175 1.1 Introduction AGP-3175 is first product of the Rugged Expandable Touch Panel Solution series. It adopts Intel® Core™ i7/i5 processor with two DDR3 800/1066 MHz SODIMM up to 8 GB. Best performance for multimedia solution AAEON's AGP-3175 also supports Intel® Core™ i7/i5 + QM57 chipset and the LVD/CRT Controller has been integrated in QM57. In addition, it equips versatile I/O ports, such as two RS-232, one RS-232/422/485, six USB2.
Rugged Expandable Touch Panel PC AGP-3175 1.
Rugged Expandable Touch Panel PC AGP-3175 1.3 Specification System z Processor Intel® Core™ i7/i5 Processor z Memory DDR3 800/1066 MHz SODIMM x 2, up to 8 GB z Chipset Intel® Core™ i7/i5 + QM57 z LCD / CRT Integrated in QM57 z Ethernet 10/100/1000Base-TX, RJ-45 x 2 z I/O Port RS-232 x 2, RS-232/422/485 x 1, USB2.0 x 6 (2 on front, 4 on rear), Line-out/MIC-in/Line-in x 1, PS/2 x 1 for Keyboard/Mouse, DVI x 1 z Storage Disk Drive 3.
Rugged Expandable Touch Panel PC AGP-3175 z Mounting Panel/ Desktop/ Rack z Dimension 16.53” x 13.95” x 4.65” (420mm x 355mm x 118mm) z Carton Dimension 24.21”(L) x 20.47”(W) x 12.99” (H) (615mm x 520mm x 330mm) z Gross Weight 24.2 lb (11 kg) z Net Weight 20.9 lb (9.
Rugged Expandable Touch Panel PC AGP-3175 LCD z Display Type 17” Color TFT LCD z Max. Resolution 1280 x 1024 z Max. Colors 16.
Rugged Expandable Touch Panel PC AGP-3175 1.
Rugged Expandable Touch Panel PC AGP-3175 Chapter 2 Hardware Installation Chapter 2 Hardware Installation 2-1
Rugged Expandable Touch Panel PC AGP-3175 2.1 Safety Precautions Always completely disconnect the power cord from your board whenever you are working on it. Do not make connections while the power is on, because a sudden rush of power can damage sensitive electronic components. Always ground yourself to remove any static charge before touching the board. Modern electronic devices are very sensitive to static electric charges. Use a grounding wrist strap at all times.
Rugged Expandable Touch Panel PC AGP-3175 2.
Rugged Expandable Touch Panel PC Solder Side Chapter 2 Hardware Installation 2-4 AGP-3175
Rugged Expandable Touch Panel PC AGP-3175 2.3 List of Jumpers There are a number of jumpers in the board that allow you to configure your system to suit your application. The table below shows the function of each jumper in the board: Label Function CMOS1 CMOS Setting Selection JP1 Auto PWRBTN Selection JP2 CFD Voltage 3.3V/5V Selection JP3 TPM Setting Selection JP5 COM1 +12V/+5V/RING Selection JP6 COM2 +12V/+5V/RING Selection 2.
Rugged Expandable Touch Panel PC AGP-3175 2.5 Setting Jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2 and 3.
Rugged Expandable Touch Panel PC AGP-3175 2.6 CMOS Setting (CMOS1) JP1 Function 1-2 Normal (Default) 2-3 Clear CMOS 2.7 Auto PWRBTN Selection (JP1) JP1 Function 1-2 Don’t use Auto PWRBTN (Default) 2-3 Use Auto PWRBTN 2.8 CFD Voltage 3.3V/5V Selection (JP2) JP2 Function 1-2 +3.3V 2-3 +5V (Default) 2.9 TPM Setting (JP3) JP3 Function 1-2 Save ME RTC Register (Default) 2-3 Clear ME RTC Register 2.
Rugged Expandable Touch Panel PC AGP-3175 2.11 COM2 +12V/+5V/RING Selection (JP6) JP6 Function 1-2 +12V 3-4 Ring (Default) 5-6 +5V 2.12 COM1~2 Port LED Connector (CN8) Pin Signal Pin Signal 1 COM1_RS232_PWR 2 GND 3 TX_LED_COM1 4 GND 5 RX_LED_COM1 6 GND 7 COM2_RS232_PWR 8 GND 9 TX_LED_COM2 10 GND 11 RX_LED_COM2 12 GND 13 COM2_RS485_PWR 14 COM2_RS422_PWR 2.
Rugged Expandable Touch Panel PC AGP-3175 5 LAN2_LED_D2 6 ACT_2_LED 7 SPD1K_2_LED 8 SPD100_2_LED 2.15 RS-232/422/485 Pin Header (COM2) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.16 RS-232 Pin Header (COM3~4) Pin Signal Pin Signal 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI 2.17 SATA Connector (SATA 1~3) Pin Signal Pin Signal 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 2.
Rugged Expandable Touch Panel PC AGP-3175 2.19 Hard Disk Drive Installation In the following, we will guide you how to install Hard Disk Drive (HDD). Make sure that all parts are provided before you start the installation.
Rugged Expandable Touch Panel PC AGP-3175 Step 3: Get the accessories of anti-vibration rubbers and screws ready Step 4: Get the screws from the rubbers and insert the anti-vibration rubbers into the fillister of the HDD bracket first Step 5: Insert the screws to the anti-vibration rubbers Chapter 2 Hardware Installation 2-11
Rugged Expandable Touch Panel PC Step 6: Put the HDD to the HDD bracket Chapter 2 Hardware Installation 2-12 AGP-3175
Rugged Expandable Touch Panel PC AGP-3175 Step 7: Connect the SATA and Power Cables to the HDD Step 8: Fasten the HDD bracket to the chassis Chapter 2 Hardware Installation 2-13
Rugged Expandable Touch Panel PC AGP-3175 2.20 Easy Stand Installation There’re two L-shaped easy stands come with the product. Refer to the following illustration to install it. 1. Fix the L-shaped easy stands with the screws on both sides of the AGP-3175.
Rugged Expandable Touch Panel PC AGP-3175 2.21 Panel Mount Kit Installation Some screw sets will come with the product for user to mount the AGP-3175 on the wall. See the steps below along with the illustration. Step 1: Bore the screw into the screw nut. Step 2: Locate the screw set into the hole around the monitor as the right illustration and pull it back to lock the screw set on the hole. Step 3: Turn the screw around to make it tight until it is closed to the wall.
Rugged Expandable Touch Panel PC AGP-3175 2.22 Waterproof Protection Step 1: Remove the non-sticky aspect of the double sided tape from the waterproof rubber border. Step 2: Put the waterproof rubber border along the bracket of the AGP-3125 chassis.
Rugged Expandable Touch Panel PC AGP-3175 Chapter 2 Hardware Installation 2-17
Rugged Expandable Touch Panel PC AGP-3175 Chapter 3 AMI BIOS Setup Chapter 3 AMI BIOS Setup 3-1
Rugged Expandable Touch Panel PC 3.1 AGP-3175 System Test and Initialization These routines test and initialize board hardware. If the routines encounter an error during the tests, you will either hear a few short beeps or see an error message on the screen. There are two kinds of errors: fatal and non-fatal. The system can usually continue the boot up sequence with non-fatal errors.
Rugged Expandable Touch Panel PC 3.2 AGP-3175 AMI BIOS Setup AMI BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed CMOS RAM so that it retains the Setup information when the power is turned off. Entering Setup Power on the computer and press or immediately. This will allow you to enter Setup. Main Set the date, use tab to switch between date elements.
Rugged Expandable Touch Panel PC AGP-3175 Chapter 4 Driver Installation Chapter 4 Driver Installation 4-1
Rugged Expandable Touch Panel PC AGP-3175 The AGP-3175 comes with a DVD-ROM that contains all drivers your need. Follow the sequence below to install the drivers: Step 1 – Install Chipset Driver Step 2 – Install VGA Driver Step 3 – Install LAN Driver Step 4 – Install AUDIO Driver Step 5 – Install ME Driver Step 6 – Install Touch Panel Driver Please read following instructions for detailed installations.
Rugged Expandable Touch Panel PC AGP-3175 4.1 Installation: Insert the AGP-3175 DVD-ROM into the DVD-ROM Drive. And install the drivers from Step 1 to Step 6 in order. Step 1 – Install Chipset Driver 1. Click on the STEP1-CHIPSET folder and select the OS your system is 2. Double click on the Setup.exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you to install the driver automatically Step 2 – Install VGA Driver 1.
Rugged Expandable Touch Panel PC AGP-3175 Step 4 – Install AUDIO Driver 1. Click on the STEP4-AUDIO folder and select the OS your system is 2. Double click on .exe file located in each OS folder 3. Follow the instructions that the window shows 4. The system will help you to install the driver automatically Step 5 – Install ME Driver 1. Click on the STEP5-ME folder and select the OS your system is 2. Double click on Setup.exe file located in each OS folder 3.
