AB 3000 Basis Unit Quad COFDM-AV Receiver, 2 Tuner KCR 342 English Notes on the Assembly Instructions. As well as this supplementary Assembly Instructions, the Assembly Instructions for the KAB 3000 apply. DCT DELTA GmbH Bodanrückstraße 1 D-78351 Bodman Phone: Fax: Email: Internet: +49 (0) 7773 / 936331 +49 (0) 7773 / 929259 info@dct-delta.de http://www.dct-delta.
Contents 1 Safety regulations........................................................................................ 3 2 General information..................................................................................... 3 2.1 Scope of delivery...........................................................................3 2.2 Meaning of the symbols used...........................................................4 2.3 Technical data...........................................................................
1 S a f e t y regulations • The standards IEC/EN/DIN EN 50083 resp. IEC/EN/DIN EN 60728 must be observed. • Do not perform installation and service work during thunderstorms. • Assembly, installation and servicing should be carried out by authorised electricians. • Switch off the operating voltage of the system before beginning with assembly or service work. • Avoid short circuits! • Observe the relevant standards, regulations and guidelines on the installation and operation of antenna systems.
2.2 M e a n i n g o f t h e s ym b o l s u s e d —> – – / / • 2.3 T e c h n i c a l Important note General note Optional use of the buttons Performing works data The requirements of the following are met: 2006/95/EC, 2004/108/EC The product fulfils the guidelines and standards for CE labelling. Unless otherwise noted all values are specified as "typical". HF input: Frequency range:....................................................... 177.5 … 858 MHz Level:......................................
2.4 D e s c r i p t i o n The COFDM AV module KCR 342, in the following called digital module, has a COFDM AV converter which simultaneously converts four COFDM modulated channels into AV signals using two DVB-T tuners. The digital module has two DVB-T inputs. Via the AV interface, the decoded video and audio signals are fed to the corresponding modulator module.
3 I n s t a l l a t i o n – Ensure the basis unit is mounted so it will not be able to vibrate. Avoid, for example, mounting the basis unit onto a lift shaft or any other wall or floor construction that vibrates in a similar way. – Before installing or changing a module, switch off the basis unit or unplug the power cable from the mains power socket. Take measures to protect against ESD! • Open the housing of the basis unit in accordance with the assembly instructions for the KAB 3000. 3.
—> Slots 1 (digital module) and 2 (modulator module) are shown in the illustration. The open slots in between (without a contact strip on the board at the rear wall of the housing) are intended for add-on modules. B A • Insert the digital module in grooves A and B of an open slot (with contact strip on the board at the rear wall of the housing) next to the associated modulator module.
3.2 Connecting t h e d i g i ta l m o d u l e HF input ”A“ HF input ”D“ C • Using the AV cable C, connect the digital module to the modulator module. • Connect the HF inputs "A" and "D" on the digital module with the corresponding cable inlets using cables made on-site.
4 T h e control panel at a glance 4.1 M e n u items Program the digital module using the buttons on the basis unit control unit. The menus appear on the two-line display of the control unit. The parameters and functions to be set are underlined.
5 P r o g r a m m i n g 5.1 P r e pa r at i o n • • • Connect the digital module to a programmed modulator module. Connect the test receiver to the HF output on the modulator module.
5.2 T h e m e n u s at a g l a n c e Bedienhinweise "blättert" Menüs vorwärts. M wählen die Eingabeposition / wählt Untermenü stellen Werte ein,. / S speichert alle Eingaben. 1 zeigt die Eingabeposition Ein/On OEM SETUP V8 Bx 1A Bx 1A TWIN-SAT Böx 4 TWIN-SAT Bx 1B QUAD C5-12,S3-24 C07 C5-12,S3-24 C07 Arte V 12 QUAD Das Erste Operating Hints scrolls forward through the menu. M select the enter position. / selects a submenu. set values and triggers actions. / S saves all entries.
WSS on TXT on / on / off / on / off M Bx 1… TESTLINES on M Bx 1… SUBTITLE txt M SUBTITLE Bx 1… off / off / txt / dvb / black 150 SUBTITLE Bx 1… west –– dvb / / M M west / east Bx 1… MEMORY S => STORE M Bx 1… SUBTITLE black / / nur wenn Untertitel verfügbar sind: Sprache auswählen only if subtitles are available: select language 40/10 / / M 0…63 page 11 CANCEL A S 5.3 P r o g r a m m i n g a module Notes: – Entries are saved by pressing the button.
—> The display shows "SETUP OEM" and the software version of the basis unit (e.g. V 8). —> The output level of the output collector can be adjusted in the "SETUP" menu (see KAB 3000 assembly instructions). S e l e c t i n g the module Bx 1A / channel strip Bx 1A TWIN-SAT Böx 4 TWIN-SAT Bx 1B QUAD C5-12,S3-24 C07 C5-12,S3-24 C07 Arte V 12 QUAD Das Erste V 12 —> The display shows, for example, the "Bx 1A QUAD" menu. "Bx" indicates the slot "1" indicates slot no.
T u n e r ( o n ly channel strip C) In this menu, select the tuner ("TUNER Line A" or "TUNER Line D") for channel strip "C" of which demodulated data stream you would like to use a station from. —> At first, programme the channel strips "A" and "D", so that transponders are set for the channel strip "C". Bx 1C INPUT TUNER Line A • Using the buttons, select "TUNER Line A" or "TUNER Line D". • Press the button. —> The "Station filter" – e.g. "Bx 1C (page 17).
—> The quality of the data stream received is indicated by two status LEDs: LED indicator Signal Green OK Red No signal Status LED ”Tuner A“ Status LED ”Tuner D“ F i n e tuning ( o n ly channel strip A and D) If necessary set the fine tuning (±64 steps) via this submenu. —> Herein you can tune to transmitters which do not match to the channel grid. —> If fine tuning is not necessary press the button to select the next menu.
Input Bx 1… C55 OK 0 —> Instead of the frequency the current value of the fine tuning is displayed. • Use the buttons to change the value step by step until the desired transmitter "locks" (indication "OK"). • Press the button. —> The "Hierarchical modulation" – "Input – Priority" menu is activated.
S tat i o n f i lt e r In this menu, select the channel from the data stream that is to be made available through this channel strip. If the message "no transponder" appears, no input signal is present. In this case, you should check the previous settings as well as the configuration of the receiving system. —> At first, programme the channel strips "A" and "D", so that transponders are set for the channel strips "B" and "C". If the "scanning ...
—> If the selected channel is broadcast with two or more audio streams, the "Audio stream for a TV channel" – "AUDIO" menu will appear. Otherwise the "Volume level" – "AUDIO Level" menu is activated (see page 18). A u d i o strea m for a TV channel This menu only appears if the selected channel is broadcast with two or more audio streams (languages). In this menu, select the desired audio stream from the transport stream.
I d e n t i f i c at i o n of the stereo / D ua l to n e In this menu, you can select whether the stereo audio identification is decoded from the VPS data or from the MPEG data stream. Further you can switch between the languages on TV stations with dual tone. Bx 1A AUDIO mpeg DUAL norm • Using the buttons, select which data stream should be decoded "mpeg" or "VPS." • Use the buttons to position the cursor under the dual tone code to be set.
A c t i vat i n g t e s t l i n es For specific applications test lines can be inserted in the teletext in this menu. Bx 1A TESTLINES on • Using the buttons switch the test lines "on" and "off" • Press the button. —> The "Teletext subtitle pages and standard, Black bar" – "SUBTITLE" menu is activated.
A c t i vat i n g t e l e t e x t s u bt i t l e pag es a n d s ta n da r d This menu allows subtitles transmitted in teletext to be displayed directly in the channel. To display the characters for Western ("west") or Eastern ("east") European languages, the corresponding character set can be selected. • Using the buttons select the submenu "SUBTITLE - txt". Bx 1A txt SUBTITLE 150 west • Using the buttons select the digit of the page number to be set. Then use to set each of the three digits.
B l ac k ba r This menu allows to mask a part of the screen ( e.g. "ticker") by a black bar. The vertical position and the height can be adjusted. • Using the buttons select the submenu "SUBTITLE - black". Bx 1A SUBTITLE black 40/10 • Using the buttons select the setting of "vertical position / height of the bar" and set the value you want using the buttons. • Press the button to activate these settings and to leave the "Setting the subtitle functions" menu.
6 F i n a l pro c e d u r es After installing the basis unit, upgrading accessories or installing modules it is necessary to tighten all cable connections, cable terminals and cover screws in order to maintain compliance with current EMC regulations. • Securely tighten the cable connections (F connectors) using an open-ended spanner (spanner gap 11 mm). • Mount the base plate and the front cover (see KAB 3000 assembly instructions).
Alterations reserved. Technical data E. & O.E.
