Quick Start Guide
Diga-Talk+
815-530-2378
sales@digatalkplus.com
710 W. Jefferson St., Joliet, IL 60435
www.digatalkplus.com
No.
1
2
4
6
8
3
5
7
9
Part Name
Volume/Channel Knob (Double click to switch the funcons)
Power On/Off
Speaker
Microphone
LED Indicators SOS Key
Microphone Jack
Programmable Keys
LCD Display
No. Part Name
Notice: Channel Knob functions must be adjusted for PTT applications.
3 5
69
2
7
8
41
Main Mic & Noise Reducon
There are two mics for the 8051. The main mic is under power
button. The sub-mic (a noise reducing mic) is on the top of the
8051, which is between the label and SIM Card/Type-C interface.
Main Mic: Without the external RM connected, the user can use P1
for PTT button and make Push-to-Talk through the main mic.
Noise Reduction Mic: The chip helps to reduce environmental
noise during VoIP calling, and bring a clearer calling experience to
customers.
LED Lights
a. The light will be off if the device is powered off.
b. There will be steady green light on the power button if the
device is powered on.
There are five LED lights on the 8051: Power status, Internet
& PTT, Wi-Fi, BT and GPS.
Power status light:
CE Warning
1. The operating temperature of the device can’t exceed 60℃ and
shouldn’t be lower than -20℃.
2. The device complies with RF specifications when the device is
used at 20cm from your body.
Hereby, Diga-Talk+ declares that this product is in compliance with
essential requirements and other relevant provisions of Directive
2014/53/EU. This product is allowed to be used in all EU member
states.
FCC Warning
15.19 Labeling requirements.
This device complies with part 15 of the FCC Rules. Operaon is
subject to the following two condions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operaon.
15.21 Informaon to user.
Any Changes or modificaons not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
15.105 Informaon to the user.
Note: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protecon
against harmful interference in a residenal installaon. This
equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instrucons, may
cause harmful interference to radio communicaons. However, there
is no guarantee that interference will not occur in a parcular
installaon. If this equipment does cause harmful interference to
radio or television recepon, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separaon between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device complies with RF specificaons when the device used at
20cm from your body.
Programmable Keys
You can install different PTT applications and set the P1, P2,
P3, P4 buttons as different functions, customize the PTT
application provider according to your needs.
a. The light will be flashing green if the device is connected to
internet during standby mode.
b. The light will be flashing red if the network is abnormal.
c.
The light will be steady red if there is no PTT connection.
d. The light will be yellow and green if the PTT is connected.
Internet & PTT light:
a. The light will be off if the BT is off.
b. The light will be flashing orange if the BT is on, but there is no other
device connected.
c. The light will be steady yellow-green if the BT is on and there is a
device connected.
BT light:
a. The light will be off if the GPS is off.
b. The light will be flashing orange if the GPS is on, but it is
still searching the satellites.
c. The light will be steady yellow-green if the GPS is on and the device
is connected with the satellites. If the light is steady yellow-green it
means the location of the device has been successfully locked, and the
high-precision positioning function can be used.
GPS light:
Part Name
P1
P2
P3
P4
PTT
Channel up
Map
Channel down
No.
1
2
3
Nome
Antenna Port
Power Port
USB Port
4 RS232 Port
5 3.5mm Audio Port
Program-
mable key
Noce:
Please check the above accessories before you discard the packing
material. Please contact your local dealer immediately if there is any
missing or damage parts.
The antenna is recommended to be fixed on the plane in the upper
right/le corner of the center console with the Logo facing upwards.
Warning: The Antenna must not be placed in the area affected by
SRS airbag.
■
■
Warranty period is 1 year from date of purchase.
This product is consistently upgrading. We reserves the right
to change the specifications of the software and/or hardware
mentioned in this operating guide without prior notice. The
product specifications and information mentioned in the
operating guide are for reference only.
Note
Installaon Steps
To guarantee opmal performance as well as a long service life of
the product, please follow the ps below.
■
Care and Cleaning
No.
1
2
3
Part Name
Mounng Bracket
Locking Knobs
Antenna Cap
Before you install the radio in a vehicle, be sure to read the
following instrucons carefully.
The radio operates with cathode-grounded power supply of 12 to
24V DC only.
Please check polarity and voltage of the power supply on the
vehicle before you install the radio.
Make sure the screws extend beyond the bottom surface of the
radio before you install it. Drill the mounting hole cautiously to
avoid damage to the vehicle wiring and other parts.
Please connect DTP supplied antenna and power cord to the
radio before you install it in the bracket. Make sure the antenna
and power cord are dedicated for DTP Systems digital radios.
Install the radio with the DTP supplied mounting bracket, to
keep it secure in case of accidents. A loose radio may cause
body injury.
Install the radio in a location where it’s easy to reach the front
panel controls.
Please make sure there’s sufficient space at the back of the
radio for wiring.
When the fuse for DC power cord needs replacement, it must be
replaced by a fuse with the same specification.
Before Use
■ Turn on the switch connects communicator with the
car battery/circuit.
■
Insert the SIM into 8051 vehicular communicator and
SIM data, or connect to a Wi-Fi/hotspot.
Product Care
■
■
Keep the product in a well ventilated space with appropriate
heat dissipation to facilitate normal working parameters.
Do not place objects on top of the product to ensure
optimal heat dissipation.
■
■
■
■
Don‘t use chemical preparaons such as stain removers, alcohol,
sprays or oil preparaons.
■
Make sure the product is completely dry before use.
Do not place the product in corrosive agents, solutions or water.
Clean the dust and fine particles from the product parts with a
clean and dry lint-free cloth or a bru
sh regularly.
Use a non-woven fabric with neutral cleanser to clean the keys,
control knobs, LCD and jacks after extended use.
Cauon: Power off the product before cleaning.
8051
Quick Start Guide
Thanks for choosing our product!
The Quick Start Guide applies to the DTP-8051 series.
Please read the Quick Start Guide before using the product.
A.
B.
C.
D.
Install the bracket in a locaon where it’s easy to operate the
device.
Connect
accessories such as antenna and power cable to the
device.
Slide the device into the mounng bracket and secure it using
the locking knobs.
Install the microphone hanger in a locaon where it can be
reached easily.
Plug the palm microphone into the microphone jack on the
front panel and place it on the hanger when not in use.
E.
Check List
Radio Unit Palm Microphone Microphone Hanger
and Screws
1 2 3
Power cable with fuse
5
Mounng Bracket Kit
6
Antenna
4
Quick Start Manual
7
P1
P2
P3
P4
2
1
3
3
2
4
1
5
1
Product Cleaning