EAP701 V1.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH FCC CAUTION This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH CE CAUTION Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP701 For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. • Radio: EN 300.328: • EMC: EN 301.489-1, EN 301.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Preface Package Contents The 4ipnet EAP701 Wall Jack Access Point is an 1. 4ipnet EAP701 x 1 in/on-the-wall as well as a ceiling-mounted Wi-Fi 2. Quick Installation Guide (QIG) x 1 IEEE 802.11b/g/n 2.4GHz 2 X 2 MIMO access point, 3. Power Adapter (DC 5V) x 1 (Optional) designed to blend into a working or a living 4. Mounting Screws x 2 environment practically and elegantly with its 5.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH System Overview Lower Panel EAP701 Lower Panel Attach Ethernet cables here to connect to the wired local network. 1 LAN 1 – 2 Ports 2 DC Jack 5V 2A Attach the power adaptor here. Upper Panel EAP701 Upper Panel 1 Restart / Reset Button Press once to restart the system; Press and hold for more than 5 seconds to reset to factory default. 2 LED Indicators 4 LED lights. Representation is listed at the top of the panel. 3 WDS Easy Setup.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Back Panel EAP701 Lower Panel 1 110 Punchdown Block Copper wire punch down for in-wall application 2 Uplink (PoE) Port For Uplink connection. This port can be used to connect to a controller, gateway, or directly to the internet. PoE is supported. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Hardware Installation Please follow the steps mentioned below to install the hardware of EAP701: Step 1. Place the EAP701 at the best location. The best location is usually at the center of your intended wireless network. The EAP701 supports two types of mounting; a) Surface Mounting Panel a) b) Outlet Mount Panel Surface Mount: Mountable on any flat surface.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Step 2. Connect one end of the Ethernet cable to the Uplink port and the other end of the cable to a switch, a router, or a hub; Or use the 110 punchdown block as your uplink connection. The 110 punchdown block may be connected with the following pin assignment: Orange Blue White Orange White Blue Brown Green White Brown White Green The EAP701 is now connected to your existing wired LAN network. Step 3.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH b) b) Align the Access Point to the 4 hooks and snap Access Point to the mounting plate c) To detach Access Point from the mounting plate, insert the Unfastening Tool (provided) horizontally into the slit, turn counter-clockwise and slide the Access Point towards the unfastening tool: Now, the Hardware Installation is complete. Punch down tools may vary by country. Please contact the 4ipnet Support Team for recommendations if needed.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Getting Started 4ipnet EAP701 supports web-based configuration. When hardware installation is complete, EAP701 can be configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above. The default values of LAN IP address and subnet mask of EAP701 are: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Steps: 1.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH 4. After a successful login to EAP701, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status will be shown. The Web Management Interface - System Overview Page 5. To logout, simply click on the Logout button at the upper-right corner of the interface to return to the Administrator Login Page. Click OK to logout. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Common Settings Step 1. Change Administrator’s Password Change Password Page Click on the Utilities icon on the main menu, and select the Change Password tab. Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Step 2. Configure General AP (Access Point) Settings Wireless General Settings Page Click on the Wireless icon on the main menu, and then select the General tab. Select the RF card you would like to set up. Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 6 for the channel. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (VAP-1 shown) The EAP701 supports up to 8 virtual APs (VAPs). Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP. (b) Choose a specific RF card to set up (c) Enable a selected VAP from the drop-down menu of Profile Name and configure related settings below.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Virtual AP Overview Page Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP701 supports up to 4 WDS links for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP701 Enterprise Access Point ENGLISH Click on the Wireless button on the main menu. Select the Repeater tab. Choose WDS as the Repeater Type. Choose the desired RF card and WDS profile: (a) Enable WDS. (b) Enter the MAC Address (peer AP) and then Click SAVE. If you are using another EAP701 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s).
