EAP220 V1.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Copyright Notice This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH FCC CAUTION This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH CE CAUTION Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP220 For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement. • Radio: EN 300.328: • EMC: EN 301.489-1, EN 301.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Preface Package Contents 4ipnet EAP220 is a high-end 802.11a/b/g/n 2.4GHz/ 5GHz MIMO Access Point (AP) with two RF cards (2.4GHz RF Card A / 5GHz RF Card B) embedded to maximize deployment flexibility and feasibility for IT administrators. 1. 4ipnet EAP220 x 1 2. Quick Installation Guide (QIG) x 1 3. CD-ROM (with User’s Manual and QIG) x 1 4. Ethernet Cable x 1 5. Console Cable x 1 6.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH System Overview Front Panel 1 2 3 4 Figure 1 EAP220 Front Panel 1 Power LED On indicates power on. 2 Status LED On indicates the system is ready. 3 WES LED For indicating WDS connection status.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Rear Panel Figure 2 EAP220 Rear Panel 1 Restart/ Reset Press once to restart the system; to reset the system to factory default settings, hold for more than 5 seconds. 2 WES Button (RF B) For IT administrators to easily setup WDS links with two RF cards. 3 Console port To access EAP220 via the console interface. 4 LAN 1 - 4 ports The ports for connections with LAN side devices.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Hardware Installation Please follow the steps mentioned below to install the hardware of EAP220: 1. Place the EAP220 at the best location. The best location for EAP220 is usually at the center of your intended wireless network. 2. Connect EAP220 to your network device. Connect one end of the Ethernet cable to the Uplink port of EAP220 and the other end of the cable to a switch, a router or a hub.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Getting Started 4ipnet EAP220 supports web-based configuration. When hardware installation is complete, EAP220 can be configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above. The default values of LAN IP address and subnet mask of EAP220 are: IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0 Steps: 1.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH 4. After a successful login to EAP220, a System Overview page of the Web Management Interface will appear, as depicted below. The Radio Status and AP Status for modules on both RF cards will be shown. The Web Management Interface - System Overview Page 5. To logout, simply click on the Logout button at the upper-right corner of the interface to return to the Administrator Login Page. Click OK to logout. Copyright © 4IPNET, INC.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Common Settings Step 1. Change Administrator’s Password Change Password Page Click on the Utilities icon on the main menu, and select the Change Password tab. Enter the old password and then a new password with a length of up to 32 characters, and retype it in the Re-enter New Password field. Click SAVE to save the changes. Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Step 2. Configure General AP (Access Point) Settings Wireless General Settings Page Click on the Wireless icon on the main menu, and then select the General tab. Select the RF card you would like to set up. Determine the Band and Channel settings: Select your preferred Band and Channel for you wireless connection. For example, select 802.11g+802.11n for the band and 6 for the channel. Note: RF Card A supports only 2.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Step 3. Configure VAP (Virtual Access Point) Profile Settings VAP Configuration Page (RF Card A : VAP-1 shown) Each embedded RF card supports up to 8 virtual APs (VAPs), which means 16 VAPs are available. Configure VAP profile settings： (a) Select the VAP Configuration tab to configure the settings of the desired VAP.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Virtual AP Overview Page Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH Step 4. Configure WDS (Wireless Distribution System) Settings (Optional) To extend the wireless coverage, EAP220 supports up to 4 WDS links per RF card for connecting wirelessly to other WDS-capable APs, or peer APs. By default, all WDS profiles are disabled. Click on the Wireless button on the main menu. Select the Repeater tab. Choose WDS as the Repeater Type. Choose the desired RF card and WDS profile: (a) Enable WDS.
Quick Installation Guide EAP220 Enterprise Access Point ENGLISH After EAP220's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments. It is strongly recommended to back up your configuration settings. For further configuration and information, please refer to the User’s Manual. P/N: V10020130606 Copyright © 4IPNET, INC.
