COGENT SYSTEMS Instruction for Mobile Ident IIIc (Mi3c) 2009‐6‐29
Cogent Systems Table of Content 1. Power On Mobile Ident IIIc (Mi3c)…………………………………………………………..3 2. Manual Check…………………………………………………………………………………………...4 2.1. Memory……………………………………………………………………………………………......4 2.2. Display……………………………………………………………………………………………….......5 2.3. Screen………………………………………………………………………………………………........5 2.4. Key……………………………………………………………………………………………………………6 2.5. Magcard…………………………………………………………………………………………………..6 2.5.1.Swipe card…………………………………………………………………………………….7 2.5.2.
Cogent Systems 1. Power On Mobile Ident IIIc (Mi3c) Press power button to power on the device. Power Button Login page will show up once the device is powered on. Enter user name and password (Test Demo: Username‐Cogent, Password‐3259600), click Login to go into the Front Page (Fig. 1) Fig.
Cogent Systems 2. Manual Check Click Manual Check in Front Page, MobileID II Test page will show up. MobileID II Test page is the main page of Manual Check. 2.1. Memory Click Memory, Memory Check dialogue will pop up. Click Start, it will calculate the memory disk automatically. After finishing memory calculation, click Quit (Fig. 2.1). Fig.2.
Cogent Systems 2.2. Display Click Display and get into it. Click Color, the screen will turn to red, blue, white and black automatically. After that it will go back to Display page. Adjust backlight by using BackLight Adjust Bar. Click OK to return to MobileID II Test page if there is no error. 2.3. Screen Click Screen and get into Touchscreen Check page. Click anywhere on the screen (exclude OK and Fault) and get into the blank page.
Cogent Systems 2.4. Key Click Key, Key Check dialogue will pop up. Power button (cancel button) is the right top key and OK button is the left top key. The interface will show the corresponding action when press cancel button and OK button. Press OK button, Left top key down will pop up, loosen it, Left top key up will pop up. Then use the same method to check cancel button. Click OK if it pass the test, click Fault if it is failed. 2.5. Magcard Click Magcar and get into it.
Cogent Systems Fig.2.5 2.5.1. Swipe Card Install the swipe card reader on the back of device. Click Swipe Card and go to the test page. Swipe the magcard on the swipe card module, there should be three rows of information of the card showing in the blank box (Fig.2.5.1). Three rows of card’s information will be shown here Fig.2.5.1 2.5.2.
Cogent Systems Writing area Numeric area Fig.2.5.2 2.5.3. ICCARD Insert IC card into the IC card reader, click ICCARD, test procedure is the same as contactless card. 2.6. Voice Click Voice and get into it. Adjust voice by adjusting the voice bar.
Cogent Systems 2.7. VibratMotor Click VibratMotor and get into it. Press Start, the device will be vibrated, press Stop, it will stop to vibrate. 2.8. Finger Adjust Click FingerAdjust and get into Camera Adjust page. Clean the fingerprint sensor, then click start to adjust the camera. Click OK on the pop up dialogue after adjusting carema. 2.9. Finger Camera Click FingerCamera and get into Finger Check page.
Cogent Systems 2.10. Facial Camera Click FacialCamera to get into Facial Check page. Click Capture to capture the image, click Save to save the image. Connect the device to PC to check the image. 2.11. Power Click Power to get into Power Check page. Select wireless you wish to open. To open wireless, you can also go into Wireless page in Front page. In Power Check page, you can also check the main and backup battery. Note: Cannot open GPS, Bluetooth, Wifi and GPRS together.
Cogent Systems 2.12. WIFI Go into Power Check page or Wireless page to power on the Wifi module. Make sure other wireless modules are power off. Then Click WIFI in Manual Check and get into Wifi Check page. Change the server IP as 172.60.5.142. Click Networks to get into Wifi Networks page, choose the best signal network, click Connect. Once it shows Connected, click Quit back to Wifi Check page. Click Connect To Server, a dialogue box will pop up indicating Connected.
Cogent Systems 2.14. GPRS Insert SIM card before check the GPRS. Go into Power Check page or Wireless page to power on the GPRS module. Make sure other wireless modules are power off. Click GPRS in Manual Check and get into GPRS Check. Change server IP as 116.6.20.59. then click Dial, waiting for the top right dialogue turn to Connected. Click Connect Server, a dialogue box will pop up to show Connected. There are some information shows under the Receive.
Cogent Systems 2.16. Barcode Click Barcode in Manual Check and get into it. Barcode camera light (red) will turn on while scanning barcode. The distance between barcode tester and Mi3c should be in 8‐16cm.
Cogent Systems 8‐16cm After the beep, Mi3c finish scanning the barcode. Now the barcode data is showed on the barcode page. Please notice the scanned barcode under should be same as the number on barcode tester. Click Continue to scan another barcode. Note: make Mi3c and barcode tester steady, do not trembling. Ensure indoor light is bright enough. Otherwise Mi3c may fail to scan the barcode because of the light spot on the barcode tester. Make sure the whole barcode is inside the scan frame.
Cogent Systems barcode tester is in 8‐16cm (can be adjusted according the scan situation). 3. Photo Click Photo in Front page. Click Capture to capture the image. Click Photo List, it will show all photos you captured. Click Exit back to Front page. 4. Settings Click Settings in Front page.
Cogent Systems 4.1. Volume Click Volume and get into it. Adjust the volume by adjusting volume bar. 4.2. Date Click Date, adjust the date by clicking ‘- ‘ or ‘+’. Click Save to save your change.
Cogent Systems 4.3. Screen Calibration Click Screen Calibration and get into it. Click the central of the cross until it finished the calibration. 4.4. Fingerprint Calibration Click Fingerprint Calibration and get into it. Clean the fingerprint sensor, click Start. It will calibrate the sensor automatically. After calibrating, it will return to the Settings page automatically.
Cogent Systems 4.5. LCD Click LCD and get into it. Adjust the LCD brightness by clicking ‘‐‘ or ‘+’ , click Save to save change. 5. Identify Click Identify in Front page and get into it. 5.1. Enroll Click Enroll and get into Base Information. After enter all the basic information, click Save to save it. Click OK to go to the next step.
Cogent Systems The next step is fingerprints captured. Enter ten fingerprints as instructed, it will capture fingerprints automatically. After capturing ten fingerprints, click Save to save the data then click OK, it will go into next step.
Cogent Systems The next step is face image captured. 5 face image need to be captured: Face_0, Face_L45, Face_R45, Face_L90, Face_R90. Click Capture to capture the face image, click Save to save the data, click OK to return back to main page. 5.2. Search Click Search, a dialogue will pop up. Select ByFinger. Press finger on the fingerprint sensor. If the fingerprint get the hit, it will show on the top, and corresponding facial image will show below.
Cogent Systems Select ByFacial. Capturing image Detected image face Captured image face FCC STATEMENT This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC ID: ZYF-BCR This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.