User's Manual
Ethernet
RS485
Power
Wiegand
Relay
Type
No
Name
Color
1
2
3
4
5
6
7
8
9
10
11
12
13
14
17
18
19
20
21
22
23
24
25
26
27
Yellow
Orange
Black
Brown
Purple
Black
White
Green
Yellow&Green
Black
Blue
Gray
Black
Red
Blue
Green
White
Yellow
7 PIN_Female
_Connector
Relay 12V+
Relay-
GND(Relay GND)
Wiegand_In_D1/LED_Input
Wiegand_In_D0
GND(Wiegand GND)
Wiegand_Out_D1
Wiegand_Out_D0
P_GND(Safety GND)
GND(RS485 GND)
RS485+
RS485-
GND(Power GND)
Power_In(12V)
RX-
RX+
TX-
TX+
UART For GPRS Module
1
3
4
8 9
14
15 20
l :
l :
l Memory:128 MB DDR/ 128MB Flash
l Expansion Memory:Micro SD(2GB for default configuration)
l LCD Display:1.8" TFT Color LCD
l LED Indicator: Multi-color × 3
l Keypad:3 X 5 keypad
l Audio:Beep
l PC Port:USB2.0
l Built-in Relay Control: 1
l Power supply:12V DC/1.5A
l Current:450mA @ 12V
l Operating Temperature:0 ~ 45˚ C
l Storage Temperature:0 ~ 45˚ C
l Fingerprint Sensor:Cogent CSD100,
500dpi Optical Sensor, (FBI Certified)
l Matching Speed:1:1 ≤1.2s,1:N ≤2s (N≤5000)
l FRR:1%
l FAR:0.001%
l Matching Security Grade:Lower, Middle, High (Configurable)
l Acceptable Fingerprint Rotation:+/-15 degree (Default)
Model ACD100P-CG
Processor SAM9G45@400MHz, Processor
LCD
LED
Key Pad
USB Port
Reset Botton
Speaker
Fingerprint Sensor
Contactless Card Area
( Part is for RF Reading Area)Keypad Card
Introduction for Function and Technical Data
Mini-Gate User Manual
Address : 10/F,Tinwe Industrial Park Phase 2, Liufang Road No.6,
Area No.67, Baoan District, ShenZhen
Tel :+ 86 - 755 - 86013579 Fax:+ 86 - 755 - 86013575
Step 1
Step 2
Step 1:
Step 2:
Step 3:
Screw stainless steel plate according to the 4 holes
marked on the drawing,choose right size of screws by
different walls
Insert installing device aimed to stainless steel plate.
Fasten this screw on the bottom.
Step 3
Step 1: Cassette(86*86)
Step 2: Screw fixing board to cassette, choose the right size of screws by
different cassettes.
Step 3: Cover the fixing board.
Step 4: Screw stainless steel plate to fixing board, then install device on
the stainless steel plate.
Option 1 : On wall directly
Step 1 Step 2 Step 3 Step 4
Option 2 : The cassette (86x86) on wall
Device Installation Guide
L spanner
1
1
List
Quantity
1
1
1
4+2
1
1
1
1
Mini-Gate biometric access control
Fixing board A (plastic)
Fixing board B (plastic)
Screw (PM4X5)
Screw(PWM3X5)
DC12V Power Connector
RJ45 Network Port Connector
Mini-Gate User Manual
Power Adapter(DC 12V/1.5A)
2
Screw(FM 2X6)