User Manual Computed Radiography Reader Doc No. : TM-401-EN Rev 0.1.1 Aug 2013 Part No. : CR-FPM-44-001-EN 3DISC, FireCR, Quantor and the 3D Cube are trademarks of 3D Imaging & Simulations Corp, South Korea, and its affiliates. All other trademarks are held by their respective owners and are used in an editorial fashion with no intention of infringement.
User Manual FireCR Flash TM-401-EN Contact 815, Tamnip-Dong, Yuseong-Gu, Daejeon, Korea Tel : 82-42-931-2100 Fax : 82-42-931-2299 Website : www.3DISCimaging.com E-mail : info@3DISCimaging.com 3DISC Americas 22560 Glenn Dr, Suite 116 Sterling, VA 20164 USA Tel : 1-703-430-6080 E-mail : info@3DISCimaging.com 3DISC Europe Gydevang, 39-41, 3450 Alleroed, Denmark Tel : 45-88-276-650 E-mail : info@3DISCimaging.
User Manual FireCR Flash TM-401-EN The device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. NOTE : This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
User Manual FireCR Flash TM-401-EN Warnings and Used Symbols To ensure the safety of patients, staff and other persons, any changes to software and hardware delivered by 3D Imaging & Simulations Corp. may only be made with prior written permission from 3D Imaging & Simulations Corp. Please read the respective manuals of the connected software, such as acquisition and diagnostic software, before starting to use the FireCR Flash system.
User Manual FireCR Flash TM-401-EN General Safety Guidelines All the safety and operating instructions should be read carefully before this device is operated. This device has been designed and tested to meet strict safety requirements applicable to medical equipment, and has been supplied in a safe condition.
User Manual FireCR Flash TM-401-EN Do not look inside of the device. If any of the following conditions occur, unplug the device from the electrical outlet and contact authorized service personnel. z The power cord or power adapter is damaged. z An object has fallen into the device. z The device has been exposed to water. z The device has been dropped or damaged. z The device does not operate correctly when the operating instructions are followed.
User Manual FireCR Flash TM-401-EN Index of contents Chapter 1. Introduction ..................................................................... 9 Chapter 2. Unpacking ......................................................................11 2.1. 2.2. Inspection for Damage ....................................................................11 Identify the Components ..................................................................11 Chapter 3. Setting Up ...............................................
User Manual FireCR Flash TM-401-EN Chapter 5. Symbols ........................................................................ 26 5.1. Manufacturer’s Declaration – Electromagnetic Emission................ 27 5.2. Manufacturer’s Declaration - Electromagnetic Immunity ................ 28 5.3. Guidance and Manufacturer ’s Declaration – Electromagnetic Immunity ..................................................................................................... 31 5.4. Laser Safety Statement .................
User Manual FireCR Flash TM-401-EN Chapter 1. Introduction Thank you very much for deciding on FireCR Flash – Computed Radiography Reader. The FireCR Flash System is ideal for a wide range of Computed Radiography examinations in specialty practices such as chiropractors, podiatrists and orthopedists.
User Manual FireCR Flash TM-401-EN Main Features State-of-the-Art Scanning Mechanism FireCR Flash adopts state-of-the-art scanning mechanisms using high beam delivery efficiency optics module to construct its compact and rigid structure. High Throughput Its unique and patented dual direction scanning mechanism enables to improve the efficiency and high throughput. Scanning Resolution User selectable resolution of 100μm and 200μm allows user to make diagnosis on variable purposes.
User Manual FireCR Flash TM-401-EN Chapter 2. Unpacking 2.1. Inspection for Damage FireCR Flash is shipped in a custom designed container to protect the reader from external shock. Before unpacking the reader, inspect the shipping container for damage. In case the container is damaged, notify the shipper immediately. 2.2. Identify the Components Identify each of these components. Part No.
User Manual FireCR Flash TM-401-EN WARNING Use of Power Cord; Type SJT or SVT, min. 18AWG, 3-Conductor, VW-1 125V, min 10A (or 250V, 10A). Max 3.0m long; One end with Hospital Grade Type, NEMA 5-15P for 125V or NEMA 6-15P for 250V. Other end with appliance coupler. “CAUTION Grounding reliability can only be achieved when the equipment is connected to an equipment receptacle marked “Hospital Only” or “Hospital Grade”.
User Manual FireCR Flash TM-401-EN Universal Cassette 35 x 43 containing IP size 35cm x 43cm Universal cassette 25 x 35 containing IP size 24cm x 30cm Universal cassette 24 x 30 containing IP size 24cm x 30cm Universal Cassette 18 x 24 containing IP size 18cm x 24cm USB 2.0 Interface cable RJ45 CAT.
User Manual FireCR Flash TM-401-EN FireKit 14
User Manual FireCR Flash TM-401-EN Chapter 3. Setting Up WARNING Unsuitable Installation Sites Locations with excessive humidity or dust Locations subject to high temperature Locations subject to shaking or vibration Locations exposed to considerable electrical or magnetic noise, or other forms of electromagnetic energy Locations with poor heat radiation 3.1.
User Manual FireCR Flash TM-401-EN DANGER Never place the reader on the floor. Sliding the reader may result in internal damage or misalignment of the optics. Install in a location that is level and stable. Installation in an unsuitable location can cause accident, or deterioration in image quality. WARNING Sliding the reader may result in internal damage or misalignment of the optics. External vibration or shock during scanning may affect image quality.
User Manual FireCR Flash TM-401-EN Free space of 50 cm (20 inch) on top side, at least, for cassette insertion and ejection. Front Side Free space of 10 cm (4 inch) on both sides, at least. Back Side Free space of 20 cm (8 inch) on back side, at least, to allow the power switch, power cord and USB cord to be reached by hand at all times. DANGER Only authorized or trained personnel should set wall mount installation.
User Manual FireCR Flash TM-401-EN DANGER Install the wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your local dealer. If installed on a slanted wall, it may fall and result in severe injury. DANGER 3D Imaging & Simulations Corp. is not liable for product damage or personal injury when the user fails to follow the product installation instruction. WARNING Pulling, pushing, or climbing on the system may cause the system fall. 3.3.
User Manual FireCR Flash 3.3.2. TM-401-EN Reader Status Indication LED Indication LED shows the status of the reader as described below. LED Green Blue On On 3.3.3. Remark System On Cassette is in initial position, and ready to scan. Ready to Scan Blinking Blinking Status Blinking Blinking Scanning Erasing Error Reader Reset Button In case that the reader is stuck during scanning, push reader reset button by sharp pin to initialize the reader.
User Manual FireCR Flash TM-401-EN Hard Disk 500 GB Free Hard Disk Space Network Video Video Resolution 1 Gbps Ethernet 32-bit Color Display 1920 x 1080, 1440 x 900 3.4.2. Minimum Requirement Operating System CPU Memory Microsoft Windows XP Intel Processor RAM 2 GB or more Hard Disk 80 GB Free Hard Disk Space Network Video Video Resolution 1 Gbps Ethernet 32-bit Color Display 1366 x 768, 1280 x 800, 1600 x 900, 1280 x 1024 3.5.
User Manual FireCR Flash 3.6.2. TM-401-EN Connect the Power Cord 1. Connect the power cord to the reader, located on the rear side. 2. Connect the other end of the cord to a grounded power outlet. DANGER This equipment must only be connected to supply mains with protective earth. Use only a three-wire cord that has grounding. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.
User Manual FireCR Flash TM-401-EN Chapter 4. Operating 4.1. System Specifications Sampling Pixel Pitch Pixel Matrix (IP 35cm x 43cm) Pixel Matrix (IP 24cm x 30cm) Pixel Matrix (IP 18cm x 24cm) Standard 200um High 100um Standard 1750 x 2150 High 3500 x 4300 Standard 1200 x 1500 High 2400 x 3000 Standard 900 x 1200 High 1800 x 2400 Accepted Cassette Size 35cm x 43cm, 25cm x 30cm, 24cm x 30cm, 18cm x 24cm Gray Scale Resolution 16 bit Eraser Embedded Computer Interface USB 2.
User Manual FireCR Flash TM-401-EN 4.2. Operation Conditions Indoor use only Operating Temperature 15°C ~ 30°C (59°F ~ 86°F) Temperature Gradient 0.
User Manual FireCR Flash TM-401-EN 4.3. Operating Instructions 4.3.1. Turn on the Reader Turn on the reader. Power switch is on the rear side of the reader. DANGER This device uses laser. Avoid looking inside of the scanner. 4.3.2. Turn on the Computer Turn on the computer. Acquisition and Diagnostic Software must be installed before operate the reader. 4.3.3.
User Manual FireCR Flash 4.3.5. TM-401-EN Circuit Functions Figure 11. Circuit diagram 9 9 9 9 9 9 Power Board : Power board generated DC Power of +15V, -15V, +5V Main Board : This parts controls peripherals for image acquisition. And it delivers amplified digitized signal to PC via USB or Ethernet.
User Manual FireCR Flash TM-401-EN Chapter 5. Symbols Symbol Description .
User Manual FireCR Flash TM-401-EN Fragile Handle with care This side up Non-ionizing electromagnetic radiation FCC ID : X68CRSCANNER5 FCC Mark Medical Equipment WITH RESPECT TO ELECTRIC SHOCK FIRE, AND MECHANICAL HAZARDS ONLY IN ACCORDANCE WITH UL60601-1 / CAN / CSA CSS.2 No. 601.1 3SE3 CE Mark 5.1. Manufacturer’s Declaration – Electromagnetic Emission The FireCR Flash system is intended for use in the electromagnetic environment specified below.
User Manual FireCR Flash TM-401-EN 5.2. Manufacturer’s Declaration - Electromagnetic Immunity The FireCR Flash system is intended for use in the electromagnetic environment specified below.
User Manual FireCR Flash Conducted RF IEC 61000-4-6 TM-401-EN 3 Vrms 150 kHz to 80 MHz 3 Vrms 150 kHz to 80 MHz Portable and mobile RF communications equipment should be used no closer to any part of the FireCR Flash system, including cables, than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter. Recommended separation distance Radiated RF IEC 61000-4-3 3 V/m 80.0 MHz to 2.5 GHz 3 V/m 80.0 MHz to 2.
User Manual FireCR Flash TM-401-EN a Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be considered.
User Manual FireCR Flash TM-401-EN 5.3. Guidance and Manufacturer ’s Declaration – Electromagnetic Immunity The FireCR Flash system is intended for use in the electromagnetic environment specified below.
User Manual FireCR Flash 5.4. TM-401-EN Laser Safety Statement The Computed Radiography Reader is Certified in the U.S. to Conform to the Requirements of DHHS 21 CFR, chapter 1 Subchapter J for Class I(1) Laser Products, and Elsewhere is Certified as a Class I(1) Laser Product Conforming to the Requirements of IEC 60825-1 : 2007. Class I(1) Laser Products are not Considered to be Hazardous.
User Manual FireCR Flash TM-401-EN Chapter 6. Warranty and Repair Service 6.1. Standard Warranty 3D Imaging & Simulations Corp. warrants its non-consumable hardware products to be free from defects in materials and workmanship. The warranty covers the cost of parts and labor to repair the product. Please keep the shipping container for future use. Products returned to the factory for repair should be properly packaged.
User Manual FireCR Flash TM-401-EN 6.4. Shipping The FireCR Flash is a solidly built system designed to survive shipping around the world. However, in order to avoid damage during shipping, the FireCR Flash must be properly packaged. In general, the best way to package the FireCR Flash is in the original factory container. If this is no longer available, we recommend that user carefully wraps the FireCR Flash in at least 75 mm (3 inch) of foam or bubble pack sheeting.
User Manual FireCR Flash TM-401-EN Chapter 7. Technical Assistance If user has any questions about installing or using the device, contact your 3D Imaging & Simulations Corp representative or your local dealer. 3D Imaging & Simulations Corp. 815, Tamnip-Dong, Yuseong-Gu, Daejeon, Korea Tel : 82-42-931-2100 Fax : 82-42-931-2299 www.3DISCimaging.
User Manual FireCR Flash TM-401-EN Appendix I Installation Report Please complete this report at the time of installation and submit the completed form signed by customer to: Fax : +82-42-931-2299 E-mail : support@3DISCimaging.