User Manual

ManualsBrands2GIG ManualsElectronicsGoControl Z-Wave Smart LED Retrofit Recessed Light Kit w/ LED Bulb (White)

LB65R6Z-1

Z-Wave Smart LED

Recessed Retroﬁ t Light Kit

Fits 5” to 6” Recessed Fixtures

LB65R6Z-1 Z-WAVE SMART LED RECESSED RETROFIT LIGHT KIT

The GoControl™ family of Z-Wave® certiﬁ ed wireless lighting products (smart

LED bulbs, switches, dimmers, outlets, and plug-in modules) and security

devices (alert sounder, passive infrared sensor and door/window transmitter)

bring a new level of intelligent wireless capability to commercial and residential

environments.

The Z-Wave wireless protocol is an international wireless standard for remote

home automation, security and other applications. Embedded in each device,

the Z-Wave smart chip enables two-way RF communication among hundreds

of Z-Wave enabled devices, allowing products and services from multiple

manufacturers to work seamlessly.

The LB65R6Z-1 Smart LED Recessed Retroﬁ t Light Kit is designed to replace

a conventional incandescent halogen downlight. It is simple to set up and

provides longer life and more energy efﬁ ciency than incandescent or ﬂ orescent

light bulbs. The ﬁ xture is instant on, without the warm-up delay common in

CFL bulbs.

GoControl Z-Wave products are easy to install, and allow dealers to create an

integrated wireless network with nearly limitless expansion and interoperability

with security, energy management, home entertainment, appliances, and more.

As part of a Z-Wave network, the LB65R6Z-1 will also act as a wireless

repeater to insure that commands intended for another device in the network

are received. This is useful when the device would otherwise be out of the radio

range of the wireless controller.

For indoor use only. Retain instructions for future use.

WARNINGS

RISK OF FIRE OR ELECTRICAL SHOCK - DO NOT EXPOSE THIS

APPARATUS TO RAIN OR MOISTURE - USE IN DRY LOCATION ONLY.

TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE

WIRING TO EDGES OF SHEET METAL OR OTHER SHARP OBJECTS.

DO NOT MAKE OR ALTER ANY OPEN HOLES IN THE ENCLOSURE OF

WIRING OR ELECTRICAL COMPONENTS DURING KIT INSTALLATION.

THIS LAMP IS NOT INTENDED FOR USE AS EMERGENCY LIGHTING.

VAPOR BARRIER MUST BE SUITABLE FOR 194° F (90° C)

THIS PRODUCT IS NOT SUITABLE FOR COVERING WITH THERMAL

INSULATED MATERIAL.

THIS PRODUCT IS NOT SUITABLE FOR MOUNTING ON A

FLAMMABLE SURFACE.

KEEP THE LIT SURFACE A MINIMUM OF 18” (.5 m) AWAY FROM ANY

FLAMMABLE OBJECT

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,LB65R6Z-1; P/N: 10007037 X7; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: FLAT 17.000” x 11.000” FOLDED 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; FOLDING: 5-FOLD ALTERNATE

650 Lumens

Equivalent

to a 65 Watt

incandescent

light bulb

NOTE: This unit must be added to the Network only where it will be permanently installed. The proper operation of this node in the

mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” conﬁ gure this unit, then install.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING

BEFORE INSTALLATION, TURN THE POWER TO THE HOUSING OFF!

Summary of content (4 pages)

PAGE 1
PRINTER’S INSTRUCTIONS: INSTR,INSTL,LB65R6Z-1; P/N: 10007037 X7; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: FLAT 17.000” x 11.000” FOLDED 8.500” x 11.000”; TOL ± .125”; SCALE: 1-1; FOLDING: 5-FOLD ALTERNATE LB65R6Z-1 Z-Wave Smart LED Recessed Retrofit Light Kit Fits 5” to 6” Recessed Fixtures 650 Lumens Equivalent to a 65 Watt incandescent light bulb NOTE: This unit must be added to the Network only where it will be permanently installed.
PAGE 2
INSTALLATION SETUP INSTALLATION (Recessed Incandescent Housing) Recessed Housing Compatibility The LB65R6Z-1 is designed to be installed in a standard 5” or 6” recessed downlight housing. For adequate clearance, it may be necessary to remove the housing’s socket mounting plate before installing the light. Housing Preparation If the existing housing has an internal socket plate, remove it from the housing. Downlight housing Housing 6.
PAGE 3
INSTALLATION (Existing Recessed LED Housing) Adding to a network: Refer to your Controller operating instructions to add this fixture under the command of the Wireless Controller. 1. With your controller in Discovery or Add Mode, turn the power to the light fixture socket ON. 2. You should see an indication on your Controller that the device was added to the network. The LB65R6Z-1 will flash twice. 3. The device will appear in the list of Switches. It should display multi-level switch.
PAGE 4
CONFIGURATION SPECIFICATIONS The LB65R6Z-1 supports the Configuration command. The LB65R6Z-1 can be configured to operate slightly differently than how it works when you first install it. Using the Configuration command you can configure the following: Parameter 1: Dim Level Memory By default, the LB65R6Z-1 bulb will go to full brightness when turned on. To have the bulb turn on to the last dim level setting, set Parameter 1 to 1.