Quick Start Guide
Intelligent Video Doorbell
Hardware Install Guide & Quick Setup
2GIG-VBELL-1
INTELLIGENT
VIDEO
DOORBELL
DOORBELL
TRANSFORMER*
CHIME BOX*
WiFi ROUTER*
WiFi COMMUNICATIONS
CLOUD
SMARTPHONE
System Description
POWER DRILL WITH 1/4” BIT
0-M
0.5
10
50
200
500
50
250
10
50
250
600
+-
AC VOLT METER
OPTIONAL
PHILLIPS SCREWDRIVER
Tools For Installation
TWO WIRES: CONNECT TO EITHER DOORBELL TERMINAL
CHIME BOX
16 VAC TRANSFORMER
Install Overview
Prepare for Installation
SHUT OFF POWER TO DOORBELL
• Shut off power to existing doorbell from the circuit breaker panel.
• Go to existing doorbell location.
VERIFY POWER SUPPLY
• The Doorbell camera is rated for 8-24 Volt AC. We recommend at least a
16V-10VA transformer.
• For some chimes that require more power, such as an electronic chime, it
may require a 16V-30VA transformer.
• Visually inspect the doorbell transformer for power rating (VA or Watts) and
Voltage.
• Measure the doorbell wiring at the installation location with a AC Volt meter.
Existing Doorbell Removal
• Remove existing doorbell pushbutton from location.
• Disconnect wires from back of pushbutton.
Install Doorbell Camera with Wire
Extenders to Mounting Plate
• If needed, use the provided twist-on wire connectors to join the two
existing AC wires to the doorbell wires.
• Push extra wire and/or connectors into the wire access hole of the
mounting plate.
1.
TWIST WIRES TOGETHER,
THEN FEED WIRES INTO
THE CONNECTOR.
2.
TWIST THE CONNECTOR.
CONNECTORS
IN PLACE
MOUNTING PLATE
Connect the Wire Extenders
• Connect the existing wire from the house directly to the video doorbell.
• Or, attach the two provided wire extenders to the hole locations on the back
of the doorbell.
• An angled mounting plate is included with your doorbell camera for
positioning the viewing eld 15 degrees to the right or left.
• The facing direction is determined by how you install the wedge.
CONNECT USING DOORBELL
WIRING FROM THE HOUSE
OR
CONNECT USING PROVIDED
WIRE EXTENDERS
FACTORY
RESET
BUTTON
RESET
BUTTON
Doorbell Camera Components
POWER KIT EXTENDER (WIRE)
L-SHAPED SCREWDRIVER
WIRE EXTENDER
SPARE SCREW
TWIST-ON WIRE
CONNECTORS (2)
SMART DOORBELL
CAMERA
ALTERNATIVE
FACEPLATE
DOORBELL WIRE
EXTENDERS
MOUNTING PLATE
(LEVEL ATTACHED)
ANGLED
MOUNTING
PLATE
POWER KIT
PHILLIPS
SCREWS (2)
ANCHORS (2)
Power
Kit
FOR SET SCREW
Mount the Doorbell Camera Plate
• Mount the plate to a at surface. If possible, use the holes from the
previous doorbell with the accompanying screws and anchors (if required).
• Use the attached level to ensure the mounting plate is level.
• If required, use the included horizontal wedge to angle the doorbell left
or right.
ALIGN MOUNTING PLATE
MOUNT WITH
SCREWS ONLY
Detach Level
MOUNT WITH
SCREWS & ANCHORS
OR
USE 1/4" (6.35mm) DRILL FOR ANCHOR HOLES
✔ Important: Once mounted, squeeze/pull the Level to detach it from the plate.
PRINTER’S INSTRUCTIONS:
INSTRUCTIONS, QUICKSTART GUIDE, 2GIG-VBELL-1 - P/N 10028260 Rev-B - INK: BLACK & PMS 186 (RED) - MATERIAL: 20 LB. MEAD BOND - DOCUMENT PRINT SIZE: 17.000” X 11.000” - TOLERANCE: ± .125” - SCALE: 1-1 - FOLDING, FOLD 3 X TO FINAL SIZE 4.1875” X 3.625” FINISH WITH LOGO SHOWING - SIDE 1 OF 2
*Not included. Refers to existing home device.
Power Kit installation is required for proper functioning of the mechanical and
electrical chime with the video doorbell. It is not needed if a chime is not used.
Install Power Kit in Chime Box
REAR TRANS
FRONT
REAR TRANS
FRONT
1 OPEN CHIME BOX
CHIME BOX FRONT VIEW
WITHOUT COVER
2 INSTALL AS SHOWN
IMPORTANT STEPS
NOTE: Power Kit connections accompany
the existing wire connections.
✔ NOTE: It is recommended to TURN POWER OFF before performing any wiring.
(Optional) Installing the Mounting Plate/Wedge
VBell_Illos_VBELL_withCurrentWedgeCongs_08June20.ai