Specification Sheet

ManualsBrands10Gtek ManualsComputers & Accessories10G SFP+ DAC Cable - 10GBASE-CU Active Direct Attach Copper Twinax SFP Cable for Brocade 10G-SFPP-TWX-0101, 1m

Table Of Contents

SFP+ Active Copper Cable Assembly

10Gtek Transceivers Co.,Ltd

Driving Your Next Generation Networks www.10gtek.com

E-mail:info@10gtek.com Tel: +86 755 2998 8100 Fax: +86 755 6162 4140

SFP+ Active Copper Cable Assembly

CAB-10GSFP-A*M（型号）

Features

 Compliant with SFF-8431 and SFF-8432

 Supports data rates up to 11.1 Gb/s

 Power Level 1 : 0.5W per cable end

 100 Ohm differential impedance

 Retractable pin latch

 EEPROM signature

 Pull to Release latch design

 360°cable braid crimp

 Enhanced EMI skirt design

 Color options for strain relief and pull tab

 Linear design for use with EDCs

 AC-coupled inputs and outputs

 Lengths up to 10m

 30AWG to 24AWG cable available

Product Applications

 Switches

 Networking – servers, routers and hubs

 Enterprise storage

 Telecommunication equipment

 Network Interface Cards (NIC’s)

Summary of content (7 pages)

PAGE 1
0Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com SFP+ Active Copper Cable Assembly CAB-10GSFP-A*M（型号） Features  Compliant with SFF-8431 and SFF-8432  Supports data rates up to 11.1 Gb/s  Power Level 1 : 0.
PAGE 2
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Applications by Protocol  10 Gigabit Ethernet and Gigabit Ethernet  (IEEE802.3ae)  Fiber channel: 1, 2, 4 and 8 GFC  Fiber Channel over Ethernet (FCoE)  Serial data transmission  InfiniBand standard Product Description 10Gtek’s Active SFP+ Copper Cables are full-active 11.1Gbps cable assemblies. The cables are compliant with the current SFF-8431, SFF-8432 and SFP+ MSA specifications.
PAGE 3
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Recommended Operation Condition Parameter Symbol Min Typ Max Unit Operating Case Temperature Topc -40 -- 85 degC Relative Humidity (non-condensation) RS - - 85 % Supply Voltage VCC3 3.135 3.30 3.465 V Power Supply Currenct ICC3 - 70 80 mA Total Power Consumption Pd - - 0.
PAGE 4
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Host board Connector Pinout Figure 1s: MSA compliant Connector Figure 2： Pin Definitions.
PAGE 5
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Notes: 1.The module signal ground pins, VeeR and VeeT, shall be isolated from the module case. 2.This pin is an open collector/drain output pin and shall be pulled up with 4.7-10k to Vcc_Host on the host board. Pull ups can be connected to multiple power supplies, however the host board design shall ensure that no module pin has voltage exceeding module VccT/R + 0.5 V. 3.
PAGE 6
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com 2 Wire Interface EEPROM The EEPROM on the SFP+ passive cable assembly is designed for 256 addresses. The information for addresses 0 to 127 is listed below. This information can be tailored to any customer request. Any address can be altered to display customer specific information and more memory can be added if more addresses are needed.
PAGE 7
10Gtek Transceivers Co.,Ltd Driving Your Next Generation Networks www.10gtek.com Mechanical Dimensions Revision History Revision Initiated Review Approved Revision History Release Date V1.0 Vinson Steven Nicky Released. Dec,24, 2013 Further Information For further information, please contact 10GTEK. Tel : +86 755 2998 8100 Fax : +86 755 6162 4140 Web: www.10gtek.com 7 E-mail:info@10gtek.