Wireless Driveway Alarm
Table of Contents 1. Package Includes........................................................ 01 2. Parts Names............................................................... 01 3. Getting Started...........................................................02 3.1 Power for Receiver......................................................................02 3.2 Power for PIR sensor...................................................................03 3.3 Paring the PIR sensors with the Receiver.....................
1. Pairing button 3. Alert Mode Button 5. Zone LED indicator 7. Receiver power indicator 9. PIR sensor working indicator 2. Melody / Next button 4. Volume button 6. DC power jack 8. PIR Sensor If powering by a power adapter, insert the adapter’s connector into the DC power jack on the side of the receiver, then plug the adapter into a power outlet. Please note that an adapter is not included and needs to be purchased separately. 3. Getting Started: 3.
● Take off the battery cover from the PIR sensor and insert 3 x AAA batteries. Reattach the battery cover and secure with the screw. ‘BEEP’ 3xAAA 1.5V Alkaline Battery Press the pairing button and you will hear a ‘Beep’ sound. 3.3 Paring the PIR sensors with the Receiver Now that the PIR sensor and receiver are powered, the PIR sensor need to be paired with your receiver before the alarm will function.
C. Wave your hand before the PIR sensors to active the PIR sensor. You will hear an alarm/melody sound if pairing is successful. Same steps to add more sensors to the alarm receiver. The driveway alarm receiver can support up to 4 sensors per zone, for a total of 16 sensors per receiver. Note: Pairing mode will stay active for 15 seconds after the sound of the ‘Beep’.
Zone 3: Dripping melody. This also is a nice melody for a low security area, such as the driveway. Zone 4: Alarm melody. This sound is tailored for high security areas. We suggest the sensor for Zone 4 be placed in areas where trespassing is a possibility. 3.5 Installing the PIR sensor It is recommended to mount the PIR sensor at least 3-4ft (1m) above the ground on a sturdy, non-metal surface (i.e.
Note: 1. Please install the sensors tightly to ensure the position and the direction will not be easy moved by wind. 3.6 Installing the Receiver The receiver can be placed on any indoor flat panel or mounted on any type of surface using the supplied screws. 1. Use a pencil to mark the location of the two mounting holes on the surface where the receiver will be installed. 2.
Note: The working distance for the receiver and PIR sensor is 300m (1000ft) without obstacle, Always test the working distance between the PIR sensor and receiver before installing these units. 3.7 Selecting the Alert Mode for the Receiver When the PIR sensors are triggered, the alarm receiver can alert you with an auditory sound, a flashing zone LED indicator, or sound and flashing zone LED indicator together. These are referred to as Sound, Flash, and Sound +Flash modes.
4. Specification: ‘BEEP’ Receiver: ● ● ● ● ● Power supply: DC 4.5V (3 x AA batteries or by an adapter) Wireless frequency: 433MHz±20KHz Operating range: 300m/1000ft (without obstacles) Receiver’s ring volume: Over 100dB within 0.5m/1.6ft Working temperature: -20°C ~ 50°C PIR Sensor: ● 3.9 Change the Volume of the Melody Press the volume button to change the ringtone’s volume. Each press will change the volume to one of six levels. Stop pressing the volume button your desired volume level is reached.
Issue Cause Solution PIR sensor Follow instruction to pair the PIR not paired sensor with the receiver. with receiver Incorrect sensor settings The alarm is not being set off Inconsistent alarms Reset all sensors (see Manufacture default settings). The working distance between sensor and receiver is about 1000ft (300m). If the PIR sensor activated, but no alarm plays on the receiver, then the PIR sensor PIR Sensor is out of range.
6. Questions? If you have any questions about your wireless driveway alarm, you can freely contact our 24H Customer Service at: Tilvisionhelp@gmail.
